Search Results

Lightweight design is a key factor in general engineering design practice, however, it often conflicts with fatigue durability. This paper presents a way for improving the effectiveness of fatigue performance dominated optimization, demonstrated through a case study on suspension brackets for heavy-duty vehicles. This case study is based on random load data collected from fatigue durability tests in proving grounds, and fatigue failures of the heavy-duty vehicle suspension brackets were observed and recorded during the tests. Multi-objective fatigue optimization was introduced by employing multiaxial time-domain fatigue analysis under random loads combined with the non-dominated sorting genetic algorithm II with archives.

The design method for the powertrain mounting system in internal combustion engine vehicles is well-established. Electric vehicles experience higher vibration frequencies and more significant transient responses when accelerating or braking than fuel vehicles due to their high speed and fast response. Therefore, the design of the electric drive assembly mounting system requires further development. The modeling of electric drive assembly mounting systems often neglects the mounting bracket’s influence, which significantly affects the center of mass and rotational inertia of the electric drive assembly. This paper examines the effect of the mounting bracket in the electric drive assembly mounting system. It establishes a mathematical model with six degrees of freedom for the mounting system, considering the mounting bracket. By comparing the natural characteristics and the transient response, it is discussed whether the mass of the mounting bracket greatly influences the system.

High-speed vehicles in low illumination environments severely blur the images used in object detectors, which poses a potential threat to object detector-based advanced driver assistance systems (ADAS) and autonomous driving systems. Augmenting the training images for object detectors is an efficient way to mitigate the threat from motion blur. However, little attention has been paid to the motion of the vehicle and the position of objects in the traffic scene, which limits the consistence between the resulting augmented images and traffic scenes. In this paper, we present a vehicle kinematics-based image augmentation algorithm by modeling and analyzing the traffic scenes to generate more realistic augmented images and achieve higher robustness improvement on object detectors against motion blur. Firstly, we propose a traffic scene model considering vehicle motion and the relationship between the vehicle and the object in the traffic scene.

In order to realize driving safety in highway scenarios, autonomous vehicles need to predict and reason about the driving intentions and motion trajectories of surrounding target vehicles in the near feature. Essentially, trajectory prediction of target vehicles can be viewed as a typical time series generation problem, which predicts the future trajectory of the vehicle through analyzing the input of historical trajectory information or its control signals. In actual traffic scenarios, the movement between vehicles is a process of mutual game and cooperation, namely the future trajectory of a vehicle is not only related to its own historical trajectory, but also to surrounding vehicles motion. However, different surrounding traffic participants have different influence on the target vehicle, and the future motion of the vehicle is often affected by some specific surrounding traffic agents deeply.

As the key assembly of new energy vehicles, the noise and vibration, and harshness (NVH) performance of integrated electric drive system directly affects the driving quality of new energy vehicles. In this paper, the vibration noise characteristic test of 3in1 electric drive system is carried out in the semi-muffler chamber. In order to compare and analyze the difference between 2in1 and 3in1 electric drive system NVH performance, the power electronics unit (PEU) in the 3in1 system was removed and placed on the ground away from the platform, and vibration noise test was carried out. In order to analyze the difference of NVH performance between 2in1 status and 3in1 status, the PEU in the 3in1 system was removed and placed on the ground far away from the bench, and the NVH test was carried out. The microphone signal at 1m position and the vibration acceleration signal of the key structural surface of the system are measured experimentally.

The mechanism of automobile brake hot spots is unclear, which is a problem in the brake industry. Complex coupling between friction, heat, contact, and structure is the main difficulty in revealing the mechanism of brake hot spots. This paper proposes a new way to study the mechanism of hot spots by analyzing the deformation behavior of brake discs under asymmetric mechanical loading. The actual brake is simplified into a brake disc and friction lining system, and a transient dynamic finite element model under asymmetric mechanical loads is established to analyze the deformation characteristics of the brake disc. The normal deformation of the brake disc under asymmetric mechanical loads consists of two parts: low-frequency bending deformation and high-frequency waviness deformation, which are caused by the squeezing effect of the asymmetric brake pressure on the brake disc and the constraint modal vibration of the brake disc.

Safety is the cornerstone for Advanced Driver Assistance Systems (ADAS) and Autonomous Driving Systems (ADS). To assess the safety of a traffic situation, it is essential to predict motion states of traffic participants in the future with mathematic models. Accurate vehicle trajectory prediction is an important prerequisite for reasonable traffic situation risk assessment and appropriate decision making. Vehicle trajectory prediction methods can be generally divided into motion model based methods and maneuver model based methods. Vehicle trajectory prediction based on motion models can be accurate and reliable only in the short term. While vehicle trajectory prediction based on maneuver models present more satisfactory performance in the long term, these maneuver models rely on machine learning methods. Abundant data should be collected to train the maneuver recognition model, which increases complexity and lowers real-time performance.

It is a worldwide technical difficulty to predict brake squeal uncertainty and its propagation regularity due to key parameters’ randomcity. However, as a widely used stochastic finite element method, Monte Carlo Method costs a large amount of time in calculation. It is very important to establish a fast prediction method for brake squeal uncertainty due to key parameters. In this paper, perturbation concept was applied for disc brake squeal uncertainty prediction. Firstly, a simplified, parameterized finite element model of disc brake was established for complex eigenvalues calculation. Then sensitivity analysis of real parts and frequencies of complex eigenvalues to influence parameters was carried out based on the finite element model. A series of second order perturbation polynomial formulas were fitted from the sensitivity analysis results, which were used for calculation of uncertain complex eigenvalues.

In this paper, the initial disc thickness variation (DTV) of a ventilated disc in automotive brake system is modeled as sinusoidal function of the second order. The transient thermomechanical coupling properties of the brake system is simulated using finite element (FE) modeling. The system models and results were verified by a thermomechanical coupling test of a disc brake conducted on a brake dynamometer. By using varied evaluation indexes such as the temperature distribution, the normal stress and the elastic deformation of disc surfaces, the influences of the initial DTV and its direction as well as its amplitude on the thermomechanical coupling characteristics were analyzed.