Search Results

Occupational populations have become increasingly diverse, requiring novel accommodation technologies for inclusive design. Hence, further attention is required to identify potential differences in work perception between workers with varying physical limitations. The major aim of this study was to identify differences in shoulder loading and perception of effort between a control population (C) and populations affected by chronic back pain (LBP) and spinal cord injury (SCI) in one-handed seated transfer tasks to targets. The effects of the injuries, and associated pain, are likely to produce variations in movement patterns, muscle loading and perceived effort.

In many task analyses using digital human figure models, only the terminal or apparently most stressful posture is analyzed. For reaches from a seated position, this is generally the posture with the hand or hands at the target. However, depending on the characteristics of the tasks and the people performing them, analyzing only the terminal posture could be misleading. This possibility was examined using data from a study of the reaching behavior of people with spinal cord injury. Participants performed two-handed forward reaching tasks. These reaches were to three targets located in the sagittal plane. The terminal postures did not differ significantly between those with spinal cord injury and those without. However, motion analysis demonstrated that they employed distinct strategies, particularly in the initial phase of motion.

The reach capability of drivers is currently represented in vehicle design practice in two ways. The SAE Recommended Practice J287 presents maximum reach capability surfaces for selected percentiles of a generic driving population. Driver reach is also simulated using digital human figure models. In typical applications, a family of figure models that span a large range of the target driver population with respect to body dimensions is positioned within a digital mockup of the driver's workstation. The articulated segments of the figure model are exercised to simulate reaching motions and driver capabilities are calculated from the constraints of the kinematic model. Both of these current methods for representing driver reach are substantially limited. The J287 surfaces are not configurable for population characteristics, do not provide the user with the ability to adjust accommodation percentiles, and do not provide any guidance on the difficulty of reaches that are attainable.

Vehicle motions can adversely affect the ability of a driver or occupant to quickly and accurately push control buttons located in many advanced vehicle control, navigation and communications systems. A pilot study was conducted using the U.S. Army Tank Automotive and Armaments Command (TACOM) Ride Motion Simulator (RMS) to assess the effects of vertical ride motion on the kinematics of reaching. The RMS was programmed to produce 0.5 g and 0.8 g peak-to-peak sinusoidal inputs at the seat-sitter interface over a range of frequencies. Two participants performed seated reaching tasks to locations typical of in-vehicle controls under static conditions and with single-frequency inputs between 0 and 10 Hz. The participants also held terminal reach postures during 0.5 to 32 Hz sine sweeps. Reach kinematics were recorded using a 10-camera VICON motion capture system. The effects of vertical ride motion on movement time, accuracy, and subjective responses were assessed.

Although biomechanics models can predict the stress on the musculoskeletal system, they cannot predict how the muscle load associated with exertion is perceived. The short-term goal of the present study was to model the perception of effort in lifting and reaching tasks. The long-term goal is to determine the correlation between objective and subjective measures of effort and use this information to predict fatigue or the risk of injury. Lifting and reaching tasks were performed in seated and standing situations. A cylindrical object and a box were moved with one hand and two hands, respectively, from a home location to shelves distributed in the space around the subject. The shoulder and torso effort required to perform these tasks were rated on a ten point visual analog scale.

A research effort was initiated to establish an empirical data base and to develop predictive models of normal human in-vehicle seated reaching motions while driving. A driving simulator was built, in which a variety of targets were positioned at typical locations a driver would possibly reach. Reaching motions towards these targets were performed by demographically representative subjects and measured by a state-of-the-art motion analysis system. This paper describes the experiment conducted to collect the movement data, and the new techniques that are being developed to process, analyze, and model the data. Some initial findings regarding the role of torso assistive motion, the effect of speed used in completing a motion on multi-segment dynamic postures, and illustrative results from kinematic modeling are presented.

Head injury is a serious threat to lives of people working around farm machinery. The consequence of head injuries are costly, paralytic, and often fatal. Clinical and biomechanical data on head injuries are reviewed and their application in the analysis of head injury risk associated with farm tractor discussed. A significant proportion of tractor-related injuries and deaths to adults, as well as children, is due directly or indirectly to head injury. An improved injury reporting program and biomechanical studies of human response to tractor rollover, runover, and falls, are needed to understand mechanisms of the associated head injury.

One of the leading causes of death and disability among young children is motor vehicle accidents. Although current child restraint systems (car seats) have significantly reduced mortality and morbidity, deaths and injuries still occur. Since it is not possible to correlate human child injury potential with the biomechanical devices used for high level impact testing using experimental methods, the acquisition and analysis of specific child injury data identifiable with real world automobile crashes is critical for input to biomechanical research, anthropometric test device (ATD) development and safety standard revisions. The purpose of this study was to analyze vehicular-related trauma that had occurred to children in known crash environments based on accident configuration and car seat design.

The automotive safety community has grown increasingly aware of the societal costs of injury impairment and disability resulting from automobile accidents. A significant portion of this impairment can be attributed to lower extremity trauma. An accident data study was conducted to determine lower extremity injury frequencies and mechanisms for restrained front-seat occupants in frontal collisions. A query of the 1988-1990 NASS (National Accident Sampling System) data provided information on pelvis, femur, knee, leg, and ankle and foot injuries. Age, gender, seating position, and delta-V were examined for their effect on the data. Lower extremity injury data were compared with injury data of similar severity (AIS ≥ 2) for the head, chest, thorax, and abdomen. The NASS data was supplemented with injury impairment information which, combined with anthropomorphic and biomechanical data, provides a prioritization scheme for the design of dummy lower extremities and instrumentation.

Lower limb injuries among motor vehicle occupants are relatively common and are one of the principle causes of permanent disability. The author has reviewed the current literature and his own experience as an orthopaedic surgeon and research accident investigator concerning lower limb injuries among motor vehicle occupants. An unreported series of knee, thigh, hip, pelvis injuries with indepth accident investigation is reported. Incidence rates for specific injury diagnoses are not available. Gross tabulations reveal that lower limb injury is second only to head injury in frequency among injured motor vehicle occupants. Lower limb injuries are possibly the commonest cause of permanent disability and impairment resulting from motor vehicle accidents.

The FMVSS were established to provide the public with uniform safety equipment and design standards based on sound research. Ongoing evaluation is essential to maintain the effectiveness and safety of FMVSS and to ensure that current technology is incorporated in standards development. Serious injury (AIS 3 or greater) reporting by NASS should be upgraded to facilitate standards evaluation and development. Although cost effectiveness is a mandated criteria for standards evaluation, the protection of human life and limb must remain the principle criteria for measuring effectiveness. A citizen's advisory panel, similar to the NMVSAC should be established to assist NHTSA in establishing priorities for standards evaluation, development and promulgation.

In a crash, impact against the steering assembly can be a major cause of serious and fatal injury to drivers. But the interrelationship between injury protection and factors of surface area, configuration, padding, relative position of the spokes, and number and stiffness of spokes and rim is not clear. This paper reports a series of high-G sled tests conducted with anesthetized animal subjects in 30 mph impacts at 30 G peaks. A total of eight tests were conducted, five utilizing pig subjects, one a female chimpanzee, one an anthropomorphic dummy, and one test with no subject. Instrumentation included closed circuit TV, a tri-axial load cell mounted between the steering wheel and column, seat belt load measurement, six Photo-Sonics 1000 fps motion picture cameras, and poloroid photography. Medical monitoring pre, during and post-impact was followed by gross and microscopic tissue examination.

Accurate data on the body dimensions of truck drivers are needed and such data are not presently available. This paper provides basic source data and an anthropometrical overview of the usefulness and limitations of existing data bases; discusses the influence of population factors, including age, sex, and demographic variables; and reviews population sampling problems. Heavy truck drivers as a whole appear to represent a physically different population from that of either the U.S. general population or other professional groups. Future anthropometric surveys must provide information for improved accommodation for the increasing range of physical size of users, and for obtaining data more useful to engineers involved in heavy truck interior cab design.

Because of its flexibility and structure, the cervical spine is disposed to various mechanisms of injury: although not so common as injuries caused by head impacts, cervical fractures and/or fracture-dislocations have been reported without direct impact to the head. Some cervical injuries reported have been sustained by wearers of lap and shoulder belts in auto accidents; however, we do not consider belt use a potential hazard because ample evidence has accrued in the medical and engineering literature to document general injury and fatality reduction by use of seatbelts. We believe that in many instances occupants would be more seriously injured or killed were belts not worn. The present paper reviews reports of cervical injuries without head impact found in the literature and case histories of such injuries from the Highway Safety Research Institute of The University of Michigan, as well as experimental studies in animals, cadavers, and volunteer subjects.

Whiplash is a poorly defined term including ligamentous and muscle strains, hematomas, disc injuries, and less frequently, brain, eye and ear injuries. Diagnosis is difficult because clinical signs and Xrays, electromyography and electroencephalography findings are few. Protection and rest will cure most patients within a year but approximately 2/5th of patients have permanent symptoms and disability. Rear-end impact accidents cause the head and neck to hyperextend over the seat back. Whiplash occurs in 38% of exposed occupants. Head rests give protection but differential rebound may occur producing injurious hyperextension and whiplash. The larynx, trachea and esophagus, in front of the spine, are injured by impact against the dash or steering wheel. Airway obstruction may occur and cause death if not restored quickly. Permanent disability can occur because of scarring and partial airway or esophageal obstruction or vocal cord damage.

This paper presents an analysis of 67 neck injuries incurred in diving and sliding accidents in swimming pools. The accidents were investigated to establish the appropriate medical and mechanical factors involved. A mathematical model was developed to allow the prediction of the trajectory and velocity of the subjects prior to their injury. Nine of the accidents were selected for real life simulation. The simulation included the selection of test subjects of similar physical build to the accident victims who then performed the maneuvers leading to the injury, but in deeper water. High speed movies (200 frames per second) were taken, above and below the water, to measure the motion. A frame by frame analysis provided data to determine the trajectory and velocity profiles of the test subject. The maneuvers studied included diving from the pool edge, diving from various board types and sliding down various sliding board configurations.

Business and executive aviation represent a combined total of over 40% of the general aviation fleet, but (1977) accounted for only 8.37% of all general aviation accidents recorded. During the period 1964-1977 some 7,351 aircraft engaged in business flying, and 883 in corporate/executive operations, were involved in accidents reported by the NTSB. These accidents were reviewed utilizing the University of Michigan Computerized Accident Files to provide an overall view of the incidence and nature of business/executive aircraft accidents relative to occupant crash injuries. In addition more detailed case studies of selected accidents investigated including a Lear Jet 25B, Cessna 421, Beech Volpar Model 18, and Ted Smith Aerostar 601, are provided to illustrate specific types of crashworthiness, occupant protection, or post-crash emergency egress findings applicable to business/executive operations. Post-crash fire was reported in 29 cases (16.3%) during the 3-year period (1975-1977).

Statistics indicate that during the past decade (1967-1976) the number of general aviation aircraft involved in an accident is equivalent to at least 38% of the total U.S. production during that period. Estimates that an aircraft will be involved in an accident over a 20 year life range are as high as 60-70%. Recognition of this probability has led to crashworthiness and occupant survivability “packaging” design concepts as offering the most realistic approach to reduction of serious and fatal injuries when an accident occurs. This paper reviews and illustrates current general aviation aircraft accident experience relative to occupant impact injury and damage indexes, and provides new data relative to current-generation aircraft.

A study of free-fall accidents and resulting injuries was conducted to determine how useful these types of data could be in establishing human injury tolerance limits. “Tolerance” was examined primarily for children at two levels - reversible injury and threat to survival. The specific objectives were to investigate specific free-falls in sufficient depth to permit biomedical or mathematical reconstruction of the fall, simulate selected free-falls to estimate impact response, and compare predicted responses with observed injuries as a means of estimating human tolerance levels. From more than 2100 reported free-falls, 110 were investigated on-site. Seven head-first and three feet-first falls were then simulated using the MVMA 2-D Crash Victim Simulator. Newspaper reports of free-falls showed that males fell six times as often as females and most often while at work. Children fell from windows and balconies more often than from any other hazard.

The importance of crashworthiness and the role of restraint systems in occupant impact protection in U.S. civil aircraft design is being increasingly recognized. Current estimates of the number of fatalities which could be prevented annually in survivable accidents range from 33 to 94%. This study reviews the development of existing Federal Aviation Administration restraint system standards from the first requirement for safety belts in the Air Commerce Regulations of 1926 to present 14 CFR 1.1. The FAA and industry standards are critically evaluated for Parts 23 (small airplanes), 25 (air transports), 27 (rotorcraft), and 29 (transport category rotorcraft). State-of-the-art developments, including an overview of previous accident experience, results of experimental studies, comparison with other standards, and primary data sources are provided.