Search Results

This specification covers procedures for ultrasonic immersion inspection of premium-grade wrought titanium and titanium alloy round billet 5 inches (127 mm) and over in nominal diameter (see 2.6.1). Metal alloy billets other than titanium may be tested to this specification with the use of suitable reference standards.

This specification covers procedures for identifying carbon and low-alloy steels, corrosion- and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy sheet, strip, and plate, and aircraft tubing.

This specification covers a corrosion- and heat-resistant nickel alloy in the form of welding wire.

The test method describes the procedure for the direct determination of water concentration in polyol ester and diester based aerospace lubricants by commercially available automated coulometric Karl Fischer titration instruments. The method was validated to cover the water concentration range of 150 to 3500 µg/g. The method may also be suitable for the determination of water concentrations outside this range and for other classes of fluids; however, the precision statement shall not be applicable for such uses.

This SAE Aerospace Recommended Practice (ARP) addresses the general procedure for the best practices for minimizing uncertainty when calibrating thermal conductivity and cold cathode vacuum gauges, which includes the vacuum sensor(s) and accompanying electronics necessary for a pressure measurement to be made. It also includes the best practices for an in-process verification where limitations make it impossible to follow the best practices for minimizing uncertainty. Verifying the accuracy and operation of vacuum gauges is critical to ensure the maintenance of processes while under vacuum.

This specification covers a precipitation hardenable corrosion- and heat-resistant nickel alloy in the form of seamless tubing.

This report specifies the minimum requirements for the Road Geometry and Attributes (RGA) data set (DS) to support road geometry related motor vehicle safety applications. Contained in this report are a concept of operations, requirements, and design, developed using a detailed systems engineering process. Utilizing the requirements, the RGA DS is defined, which includes the DS Abstract Syntax Notation One (ASN.1) format, data frames, and data element definitions. The requirements are intended to enable the exchange of the messages and their DS information to provide the desired interoperability and data integrity to support the applications considered within this report, as well as other applications which may be able to utilize the DS information. System requirements beyond this are outside the scope of this report. NOTE: Unless otherwise marked as Informative, all material in this report is to be considered normative.

This recommended practice is derived from common test sequences used within the industry. This procedure applies to all on-road passenger cars and light trucks up to 4 540 kg of GVWR. This recommended practice does not address other aspects such as performance, NVH, and durability. Test results from this recommended practice should be combined with other measurements and dynamometer tests (or vehicle-level tests), and acceptance criteria to validate a given design or configuration.

Subject document is specifically intended for service brakes and service brakes when used for parking and/or emergency brakes (only) that are commonly used for automotive-type, ground-wheeled vehicles exceeding 4536 kg (10000 pounds) gross vehicle weight rating (GVWR). Subject specification provides the off-vehicle procedures, methods, and processes used to objectively determine suitability of tactical and combat ground-wheeled vehicle brake systems and selected secondary-item brake components (aka, aftermarket or spare parts), including brake “block” for commercial applications only, specifically identified within subject document. Subject specification is primarily based on known industry and military test standards utilizing brake inertia dynamometers. Targeted vehicles and components include, but may not be limited to, the following:a.

This SAE Aerospace Information Report (AIR) provides information to be considered when performing the safety assessment of electrified propulsion aircraft. Its main focuses are: ● Typical new technologies introduced by electrified propulsion and their impact on safety ● The failure modes of electrified propulsion systems and their components ● Potential effects of failures at system and aircraft levels ● Possible strategies to minimize failures and mitigate their effects The information in this document may be used to generate inputs for system and aircraft safety assessments based on industry standards such as SAE ARP4761. The first issue of this document addresses battery systems, power electronics, eMotors, electrical interconnects and thermal management for fully electric configurations. Future issues are expected to address other subsystems, components and configurations.

This SAE Standard applies to all combinations of pneumatic tires, wheels, or runflat devices (only as defined in SAE J2013) for military tactical wheeled vehicles only as defined in SAE J2013. This applies to original equipment and new replacement tires, retread tires, wheels, or runflat devices.This document describes tests and test methodology, which will be used to evaluate and measure tire/wheel/runflat system and changes in vehicle performance.All of the tests included in this document are not required for each tire/wheel/runflat assembly. The Government Tire Engineering Office and Program Office for the vehicle system have the responsibility for the selection of a specific test(s) to be used. The selected test(s) should be limited to that required to evaluate the tire/wheel/runflat system and changes in vehicle performance.

This document is intended to supplement the SAE J1939 documents by offering the SAE J1939 information in a form that can be sorted and search for easier use.

Automated driving system (ADS) manufacturers, developers, and operators need to provide clear information on their safety approach to relevant stakeholders. Explainability to diverse audiences helps build trust in statements from these organizations towards the shared value of safety. A defined list of core safety topics can help set expectations when communicating deployment and use-case-specific automated vehicle (AV) safety information. The topics listed in this best practice are implementation-agnostic and broadly applicable. This best practice describes how safety is continuous and connected throughout lifecycle stages and highlights considerations when including safety metrics as part of the communicated information. It lists topics that are considered core, provides a rationale, illustrative examples where applicable, suggestions of content that could be included for the example, and lists references and industry examples for further information.

To define test cases for the OBD-II interface on external test equipment (such as an OBD-II Scan Tool, Inspection/Maintenance Tester, etc.) which can be used to verify compliance with the applicable standards such as SAE J1978 and SAE J1979 for Passenger Cars, Light-Duty Trucks, and Medium-Duty Vehicles and Engines (OBD II).

This SAE Aerospace Standard (AS) establishes minimum requirements for eddy current inspection of circular holes in nonferrous, metallic, low conductivity (less than 5% IACS) aircraft engine hardware with fasteners removed. The inspection is intended to be performed at maintenance and overhaul facilities on engine run hardware.

This specification covers one type of fluorescent magnetic particles in the form of a mixed, ready-to-use suspension in an odorless, inspection oil vehicle and packaged in aerosol cans.

This is for testing purposes

ARP4754B Clarification Notice to address typographical errors and clarify portions of the document to facilitate usage of the newly released ARP4754B.

The document describes typical processes with examples on how to manage reliability assessment hardware and software used on structural health monitoring systems, and for structure health management solutions. It addresses reliability assessment guidelines from design phase, manufacturing, assemblies, installation, considering installation and environmental conditions. Link between Quality system and reliability assessment is developed

This document will provide topics and possible content for industry to use in setting up training programs for personnel involved in deployment of SHM systems. The two primary parts of the training are: installation and usage.