Search Results

This specification covers fuel-resistant polysulfide (T) sealing compounds supplied as a two-component system.

This SAE Aerospace Standard (AS) defines minimum performance standards (MPS) for fuel flowmeters, fuel flow indicators, and fuel flow transmitters. The fuel flow indicators and transmitters are intended for use in 14 CFR Part 23, 25, 27, and 29 aircraft equipped with reciprocating and turbine engines. Multiple function displays are not within the scope of this SAE Aerospace Standard (refer to AS6296).

This SAE Aerospace Standard (AS) provides the general performance, design, installation, test, development, and quality assurance requirements for the flight control related functions of the Vehicle Management Systems (VMS) of military piloted aircraft. It also provides specification guidance for the flight control interfaces with other systems and subsystems of the aircraft.

The SAE AE-5CH Taskgroup has determined that high flow liquid hydrogen fueling couplings need to be developed in order to fast fill aircraft at the airport. Though the flow rates from a current liquid hydrogen bayonet connect may reach the lower bound flow rates of regional aircraft, there are some shortcomings to this connector for aerospace. For this reason a new specification for flow rates for regional to narrowbody (and potentially later widebody) are to be developed in this documenet. Harmonization for lower flow rates (such as up to 20kg/minute) are planned to be harmonized with ground vehicle fueling such as with ISO 13984. Within this document,coupling descriptions including Flow rates from 84 to 200 kg/minute will be evaluated (and potentially higher), and requirements and testing and safety targets will be specified.

Ultra-Downsizing (UD) was introduced as an even higher level of downsizing for Internal Combustion Engines ICEs, see [2] SAE 2015-01-1252. The introduction of Ultra Downsizing (UD) aims to enhance the power, efficiency, and sustainability of ICEs while maintaining the thermal and mechanical strain within acceptable limits. The following approaches are utilized: 1 True Atkinson Cycles are implemented utilizing an asymmetrical crank mechanism called Variable Compression and Stroke Ratios (VCSR). This mechanism allows for extended expansion stroke and continuous adjustment of the Volumetric Compression Ratio (VCR). 2 Unrestricted two or more stage high-pressure turbocharging and intensive intercooling: This setup enables more complete filling of the cylinder and reduces the compression work on the piston, resulting in higher specific power and efficiency. 3 The new Load Control (LC) approach is based to continuous VCR adjustment.

The problem of keeping the stable starting performance of diesel engine under high altitude and low temperature conditions has been done a lot of research in the field of diesel engine, but there is a lack of research on extreme conditions such as above 2000 meters above sea level and below 0°C. Aiming at solving the cold start problem of diesel engine in extreme environment, a set of chamber system of cold start environment diesel engine was constructed to simulate environment of 3000m altitude and -20°C. A series of experimental research was conducted on cold start efficiency optimization strategy of a certain type of diesel engine at 3000m altitude and -20°C. In parallel, a diesel engine model was constructed through Chemkin to explore the influence of the three parameters of compression ratio, stroke length, and fuel injection advance angle on the first cold start cycle of diesel engine at 4000m altitude and -20°C.

This SAE Aerospace Information Report (AIR) covers forced air technology including: reference material, equipment, safety, operation, and methodology. This resource document is intended to provide information and minimum safety guidelines regarding use of forced air or forced air/fluid equipment to remove frozen contaminants. During the effective period of this document, relevant sections herein should be considered and included in all/any relevant SAE documents.

This SAE Aerospace Recommended Practice (ARP) provides the technical terms and nomenclature, together with their definitions and abbreviations/acronyms that are used in aerospace fluid power, actuation and control systems. NOTE: ARP490 and ARP4493 are sources for definitions specifically for electrohydraulic servovalves.

In radiography testing, the radioactive elements Iridium 192 (Ir192) and Cobalt 60 (Co60) are employed to detect subsurface and inner flaws. These radioactive components are kept secure within the radiation-protected source camera. Despite the fact that the camera is safe, there is a little quantity of radiation that may harm human body cells. In this present study, it restricts radiation emission by placing a lead sheet over the source camera, which absorbs the produced radiation. The innovative concept involves in this present work is to place a manually operated switch near the radiation source to emit radiation.

This specification covers a fluorocarbon (FKM) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. For molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the AMS7259 specification.

Abstract TOC

This Aerospace Recommended Practice (ARP) provides general requirements for a generic, integrated rudder and brake pedal unit, incorporating a passive force-feel system that could be used for fixed-wing fly-by wire transport and business aircraft.This ARP addresses the following:- The functions to be implemented- The mechanical interconnection between captain and F/O station- The geometric and mechanical characteristics- The mechanical, electrical, and electronic interfaces- The safety and certification requirements

This specification covers a high strength fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-ring cord, and molded in place gaskets for aeronautical and aerospace applications.