Search Results

The double-V micro-structures (DVMS) are a type of auxetic materials showing the negative Poisson’s ratio which can contract under compression different from the conventional materials. Due to the unique properties, it can have higher stiffness and better impact resistance with lightweight. In this paper, a cylindrical honeycomb tube based on the double-V unit cell is proposed. Firstly, the nominal Poisson’s ration and Young’s modulus in the longitudinal and circumferential directions are derived analytically. The effect of the geometry parameters of the DVMS tube on the mechanical properties is studied thoroughly. Also, the effect of the width in the radial direction on these mechanical properties is analyzed. Secondly, the finite element (FE) method is utilized to obtain the numerical solutions and verify the accuracy of the analytical solutions. The results show that there is a good agreement between the results obtained by the two methods when the width is smaller enough.

Signals indicative of in-cylinder combustion have been under investigation for the control of diesel engines to meet stringent emission standards and other production targets in performance and fuel economy. This paper presents the results of an investigation on the use of the ion current signal for the close loop control of a heavy duty four cylinder turbocharged diesel engine equipped with a common rail injection system. A correlation is developed between the start of ion current signal (SIC) and the location of the peak of premixed combustion (LPPC) in the rate of heat release trace. Based on this correlation, a PID closed loop controller is developed to adjust the injection timing for proper combustion phasing under steady and transient engine operating conditions.

The objective of this research is to develop protection from high velocity projectile and blast load for commercial passenger automobiles such as VIP cars and the Armored Trucks which collect Cash from Banks and shops. Nano-material reinforced composites offer a good opportunity for developing a high velocity impact and blast protection to the commercial cars and trucks from projectiles and blast loads. These methods can be used for homeland security vehicles also. At first, a modeling, simulation, and design tool for nano-composites was developed to predict, with accepted fidelity, nano-composite behaviors. Using a unit cell model created for nanoclay-epoxy composites, the effect of nanoparticle distribution on the maximum stress developed in epoxy resin was investigated with the Meshfree Particle Method. The ensemble average of mechanical property for nanoclay-epoxy composite was studied.

EGR is a proven technology used to reduce NOx formation in both compression and spark ignition engines by reducing the combustion temperature. In order to further increase its efficiency the recirculated gases are subjected to cooling. However, this leads to a higher load on the cooling system of the engine, thus requiring a larger radiator. In the case of turbocharged engines the large variations of the pressures, especially in the exhaust manifold, produce a highly pulsating EGR flow leading to non-steady-state heat transfer in the cooler. The current research presents a method of determining the pulsating flow field and the instantaneous heat transfer in the EGR heat exchanger. The processes are simulated using the CFD code FIRE (AVL) and the results are subjected to validation by comparison with the experimental data obtained on a 2.5 liter, four cylinder, common rail and turbocharged diesel engine.

The focus of this study is to determine the effect of using B-20 (a blend of 20% soybean methyl ester biodiesel and 80% ultra low sulfur diesel fuel) on the combustion process, performance and exhaust emissions in a High Speed Direct Injection (HSDI) diesel engine equipped with a common rail injection system. The engine was operated under simulated turbocharged conditions with 3-bar indicated mean effective pressure and 1500 rpm engine speed. The experiments covered a wide range of injection pressures and EGR rates. The rate of heat release trace has been analyzed in details to determine the effect of the properties of biodiesel on auto ignition and combustion processes and their impact on engine out emissions. The results and the conclusions are supported by a statistical analysis of data that provides a quantitative significance of the effects of the two fuels on engine out emissions.

The objective of this work is to develop a strategy to reduce the penalties in the diesel engine performance, fuel economy and HC and CO emissions, associated with the operation in the low temperature combustion regime. Experiments were conducted on a research high speed, single cylinder, 4-valve, small-bore direct injection diesel engine equipped with a common rail injection system under simulated turbocharged conditions, at IMEP = 3 bar and engine speed = 1500 rpm. EGR rates were varied over a wide range to cover engine operation from the conventional to the LTC regime, up to the misfiring point. The injection pressure was varied from 600 bar to 1200 bar. Injection timing was adjusted to cover three different LPPCs (Location of the Peak rate of heat release due to the Premixed Combustion fraction) at 10.5° aTDC, 5 aTDC and 2 aTDC. The swirl ratio was varied from 1.44 to 7.12. Four steps are taken to move from LTC to ALTC.

An advanced design methodology is developed for innovative composite structure concepts which can be used in the Army's future ground vehicle systems to protect vehicle and occupants against various explosives. The multi-level and multi-scenario blast simulation and design system integrates three major technologies: a newly developed landmine-soil-composite interaction model; an advanced design methodology, called Function-Oriented Material Design (FOMD); and a novel patent-pending composite material concept, called BTR (Biomimetic Tendon-Reinforced) material. Example results include numerical simulation of a BTR composite under a blast event. The developed blast simulation and design system will enable the prediction, design, and prototyping of blast-protective composite structures for a wide range of damage scenarios in various blast events.

One of the most challenging problems in diesel engines is to reduce unburned HC emissions that appear as (white smoke) during cold starting. In this paper the research is carried out on a 4-cylinder diesel engine with a common rail fuel injection system, which is able to deliver multiple injections during cold start. The causes of combustion failure at lower temperature limits are investigated theoretically by considering the rate of heat release. The results of this clearly indicate that in addition to low cranking engine speed, heat transfer and blow-by losses at lower ambient temperatures, fuel injection events would contribute to the failure of combustion. Also, combustion failure takes place when the compression temperature is lower than some critical value. Based on these results, split-main injection strategy was applied during engine cold starting and validated by experiments in a cold room at lower ambient temperatures.

This paper presents tribological modeling, experimental work, and validation of tribology parameters of a single cylinder turbocharged diesel engine run at various loads, speeds, intake boost pressures, and cylinder liner temperatures. Analysis were made on piston rings and liner materials, rings mechanical and thermal loads, contact pressure between rings and liner, and lubricant conditions. The engine tribology parameters were measured, and used to validate the engine tribology models. These tribology parameters are: oil film thickness, coefficient of friction between rings and liner, friction force, friction power, friction torque, shear rate, shear stress and wear of the sliding surfaces. In order to measure the oil film thickness between rings and liner, a single cylinder AVL turbocharged diesel engine was instrumented to accept the difference in voltage drop method between rings, oil film, and liner.

Thermal barrier coatings (TBC) are perceived as enabling technology to increase low heat rejection (LHR) diesel engine performance and improve its longevity. The state of the art of thermal barrier coating is the plasma spray zirconia. In addition, other material systems have been investigated for the next generation of thermal barrier coatings. The purpose of this TBC program is to focus on developing binder systems with low thermal conductivity materials to improve the coating durability under high load and temperature cyclical conditions encountered in the real engine. Research and development (R&D) and analysis were conducted on aluminum alloy piston for high output turbocharged diesel engine coated with TBC.

Adiabatics, Inc., with the support of the U.S. Army Tank Automotive Research & Development Engineering Center (TARDEC) has developed a low cost, durable ceramic composite cylinder bore coating for diesel engines operating under severe conditions. This bore coating is a ceramic composite consisting primarily of Iron Oxide, Iron Titanate and Partially Stabilized Zirconia. It is applied by unique chemical thermal bonding technology developed at Adiabatics, Inc. and is referred to as Low Temperature Iron Titanate (LTIT). This coating has been tested against a wide range of cylinder bore treatments ranging from hard chrome plate to hard Nickel Silicon Carbide (NikaSil) and found to provide a superior sliding wear surface. It is superior because it is compatible against most common piston ring materials and coatings.

The simulation of I.C. Engines operation, especially during transients, requires a fairly accurate estimation of the internal mechanical losses of the engine. The paper presents generic friction models for the main friction components of the engine (piston-ring-liner assembly, bearings and valve train), considering geometry of the engine parts and peculiarities of the corresponding lubrication processes. Separate models for the mechanical losses introduced by the injection system, oil and water pumps are also developed. All models are implemented as SIMULINK modules in a complex engine simulation code developed in SIMULINK and capable to simulate both steady state and transient operating conditions. Validation is achieved by comparison with measurements made on a four cylinder, common rail diesel engine, on a test bench capable to run controlled transients.

Vehicle structure crashworthiness design is one of the most challenging problems in product development and it has been studied for decades. Challenges still remain, which include developing a reliable and systematic approach for general crashworthiness design problems, which can be used to design an optimum vehicle structure in terms of topology, shape, and size, and for both structural layout and material layout. In this paper, an advanced and systematic approach is presented, which is called Magic Cube (MQ) approach for crashworthiness design. The proposed MQ approach consists of three major dimensions: Decomposition, Design Methodology, and General Considerations. The Decomposition dimension is related to the major approaches developed for the crashworthiness design problem, which has three layers: Time (Process) Decomposition, Space Decomposition, and Scale Decomposition.

Previous research [1] using an advanced multi-domain topology optimization technique has shown a great promise for the crashworthiness design using the new technique. In this paper, we try to answer some fundamental questions regarding the crashworthiness design, which include: 1) what are the fundamental crash mechanisms of a general crash process; 2) how the uncertainties in the system will affect the crash behavior of a structure; and 3) what is the proper approach for the crashworthiness design optimization that will have needed effectiveness and efficiency. In this paper, three different kinds of uncertainties, uncertainties in the structural parameters, the modeling processes, and the loading and boundary conditions, will be considered to assess the effects of the uncertainties in the crash process. The possible crash mechanisms are then studied to provide an understanding for the design problem.

Past experience has shown that the power density of an engine itself is not a sufficient guide to determine whether it will meet the power density needs of the intended combat vehicle application. The real need is for the complete propulsion system to be power dense. Here the definition of the propulsion system includes the engine, transmission, cooling system, air filtration system, intake and exhaust ducting, controls, accessories, batteries, fuel system and final drives. The power pack is a subset of the propulsion system and consists of that part of the propulsion system that would be lifted out of the vehicle for service or replacement and would typically consist of at least the engine, and transmission, cooling system, and power pack controls and ideally would also include the air filtration system and accessory drives. Engine operating characteristics will directly impact power density for some propulsion system items.

A method for indirectly determining the laminar flame speed for diesel fuel was formulated and benchmarked against cylinder pressure data acquired for two direct-injection diesel engines. The approach was focused on fitting a series of experimentally generated heat release and mean cylinder pressure profiles with a zero-dimensional, physics-based combustion model. A correlation for laminar flame speed was generated based on the optimal fit of flame speed to this series of heat release profiles. This technique resulted in a correlation that had a reasonable RMS error and exhibited trends that have been observed with lighter hydrocarbon fuels such as gasoline including pressure and air fuel ratio behavior.

The disturbances in the cylinder gas pressure trace caused by combustion in internal combustion engines have an impact on the shape of the rate of heat (energy) release (RHR). It is necessary to smooth the pressure trace before carrying out the RHR calculations and making any interpretations for the combustion process. Different smoothing methods are analyzed and their features compared. Furthermore, the selection of the smoothing starting point and its effect on the smoothing quality of pressure data are described. The Fast Fourier Transform (FFT) analysis is applied to determine the frequency of the disturbances in power spectrum and obtain the optimal specified smoothing parameter (SSP). The experimental data was obtained on a single-cylinder research diesel engine, running under simulated turbocharged steady state conditions. The experiments covered a wide range of engine operating parameters such as injection pressures, injection timing, and EGR ratios.

A multi-domain and multi-step topology optimization approach has been developed to address a wide range of structural design problems with manufacturability and other application concerns. The potential applications have been demonstrated in our previous work [1,2]. In this paper, we try to extend this method for vehicle crash design problem. The design process will be explained and examples will be provided to illustrate the potential application of this method for complicated crash design problems.

DKAD is an automated analysis tool for evaluating dynamic characteristics of accessory drives. Rotation response analysis predicts natural frequencies and effects of crankshaft excitation. Lateral response of each belt span shows the effect of pulley run-out and parametric excitation. DKAD systematically allows a user to define a design and its operating conditions and then performs a sequence of analysis to visualize the rotational and lateral responses. It also allows a user to quickly explore and assess alternative designs. Belt layout and associated parameters can be saved in templates for future reference.

Adiabatics, Inc. with the support of the U.S. Army Tank Automotive & Armaments Command has examined the feasibility of using Diamond Like Carbon (DLC) films and Iron Titanate (Fe2TiO5 or IT) for sliding contact surfaces in Low Heat Rejection (LHR) diesel engines. DLCs have long been a popular candidate for use in sliding contact tribo-surfaces where a perceived reduction of friction losses will result in increased engine efficiency [1]. There exists a broad range of technologies for applying DLC films. This paper examines several types of these technologies and their future application to automotive internal combustion engines. Our work focuses upon DLC use for LHR military diesel engines where operating temperatures and pressures are higher than conventional diesel engines. However, a direct transfer of this technology to automotive diesel or gasoline engines exists for these thin films.