Search Results

To control the auto ignition in end-gas region and to achieve higher thermal efficiency in a natural gas dual fuel engine operated under PREMIER combustion mode where the end-gas auto ignition occurs without knocking-like oscillation, the EGR (exhaust gas recirculation) and supercharging were applied. The EGR rate and the intake air pressure as well as the pilot injection timing of diesel fuel were varied, and the profiles of the in-cylinder pressure, the exhaust emissions and the heat balance were examined at the indicated mean effective pressure around 680 kPa. The experimental results showed that higher thermal efficiency can be achieved with the combination of the PREMIER combustion and the EGR rate of 30% due to the improvements in the combustion efficiency and the degree of constant volume heat release while reducing the cooling loss.

In this research, a spark plug with an optical fiber has been developed to obtain the emission spectra from the spark discharge and flame kernel. This developed spark plug with an optical fiber can obtain the time series of emission spectra from the spark discharge and Initial flame kernel in the real spark-ignition engine using EMCCD spectrometer. The plasma vibrational temperature of the spark discharge can be measured using the emission spectra from the electrically excited CN violet band system. The plasma of the spark discharge and gas rotational temperature of the initial flame kernel can be also measured using emission spectra from OH* radicals (P and R branches). The plasma temperature of the spark discharge was almost 8,000 K and the gas temperature of the Initial flame kernel approached that of the adiabatic flame temperature.

The authors have previously proposed a plume ignition and combustion concept (i.e., PCC combustion), in which a hydrogen fuel is directly injected to the combustion chamber in the latter half of compression stroke and forms a richer mixture plume. By combusting the plume, both cooling losses and NOx formation are reduced. In this study, thermal efficiency was substantially improved and NOx formation was reduced with PCC combustion by optimizing such characteristics as direction and diameter of the jets in combination with combustion of lean mixture. Output power declined due to the lean mixture, however, was recovered by supercharging while keeping NOx emissions at the same level. Thermal efficiency was further improved by slightly re-optimizing the jet conditions.

The present study helps to understand the local combustion characteristics of PREmixed Mixture Ignition in the End-gas Region (PREMIER) combustion mode while using increasing amount of natural gas as a diesel substitute in conventional CI engine. In order to reduce NOx emission and diesel fuel consumption micro-pilot diesel injection in premixed natural gas-air mixture is a promising technique. New strategy has been employed to simulate dual fuel combustion which uses well established combustion models. Main focus of the simulation is at detection of an end gas ignition, and creating an unified modeling approach for dual fuel combustion. In this study G-equation flame propagation model is used with detailed chemistry in order to detect end-gas ignition in overall low temperature combustion. This combustion simulation model is validated using comparison with experimental data for dual fuel engine.

The Microwave Discharge Igniter (MDI) was developed to create microwave plasma for ignition improvement inside combustion engines. The MDI plasma discharge is generated using the principle of microwave resonance with microwave (MW) originating from a 2.45 GHz semiconductor oscillator; it is then further enhanced and sustained using MW from the same source. The flexibility in the control of semiconductors allows multiple variations of MW signal which in turn, affects the resonating plasma characteristics and subsequently the combustion performance. In this study, a wide range of different MW signal parameters that were used for the control of MDI were selected for a parametric study of the generated Microwave Plasma. Schlieren imaging of the MDI-ignited propane flame were carried out to assess the impact on combustion quality of different MW parameters combinations.

Recent trend in gasoline-powered automobiles focuses heavily on reducing the CO2 emissions and improving fuel efficiency. Part of the solutions involve changes in combustion chamber geometry to allow for higher turbulence, higher compression ratio which can greatly improve efficiencies. However, the changes are limited by the ignition-source and its location constraint, especially in the case of direct injection SI engines where mixture stratification is important. A new compact microwave plasma igniter based on the principle of microwave resonance was developed and tested for propane combustion inside a constant volume chamber. The igniter was constructed from a thin ceramic panel with metal inlay tuned to the corresponding resonance frequency. Microwaves generated by semiconductor based oscillator were utilized for initiation of discharge. The small and flat form factor of the flat panel igniter allows it to be installed at any locations on the surface of the combustion chamber.

Exhaust gas recirculation (EGR) has proven to be beneficial for not only fuel economy improvement but also knock and emissions reduction. Combined with lean burning, it can assist gasoline engines to become cleaner, more efficient and to meet the stringent emissions limit. However, there is a practical limit for EGR percentage in current engines due to many constraints, one of which being the ignition source. The Microwave Discharge Igniter (MDI), which generates, enhances and sustains plasma discharge using microwave (MW) resonance was tested to assess its ability in extending the dilution limit. A combination of high-speed Schlieren imaging and pressure measurements were performed for propane-air mixture combustion inside a constant volume chamber to compare the dilution limits between MDI and conventional spark plug. Carbon dioxide addition was carried out during mixture preparation to simulate the dilution condition of EGR and limit the oxygen fraction.

Requirements for reducing consumption of hydrocarbon fuels, as well as reducing emissions force the scientific community to develop new ignition systems. One of possible solutions is an extension of the lean ignition limit of stable combustion. With the decrease of the stoichiometry of combustible mixture the minimal size of the ignition kernel (necessary for development of combustion) increases. Therefore, it is necessary to use some special techniques to extend the ignition kernel region. Pulsed microwave discharge allows the formation of the ignition kernels of larger diameters. Although the microwave discharge igniter (MDI) was already tested for initiation of combustion and demonstrated quite promising results, the parameters of plasma was not yet studied before. Present work demonstrates the results of the dynamics of spatial structure of the MDI plasma with nanosecond time resolution.

High speed, time resolved Particle Image Velocimetry (PIV) diagnostics was applied to an optical SI engine to study the interactions between in-cylinder flow field and flame development. Optimisation and certain adaptations have been made to the diagnostic setup to enable time-resolved, simultaneous measurements of both PIV data and flame tomography imaging from the same original captured image set. In this particular study, interactions between flow and flame during lean-burn operating conditions at various tumble strength have been investigated and compared to a standard stoichiometric operation. Diagnostics were performed for both the vertical plane (x-y) and the horizontal plane (r-⊖) of the combustion chamber with a particular focus in the pent-roof area. Some major differences in the tumble flow-field prior to ignition has been observed between the lean and stoichiometric conditions.

The effect of microwave enhanced plasma (MW Plasma) on diesel spray combustion was investigated inside a constant volume high pressure chamber. A microwave-enhanced plasma system, in which plasma discharge generated by a spark plug was amplified using microwave pulses, was used as plasma source. This plasma was introduced to the soot cloud after the occurrence of autoignition, downstream of the flame lift-off position to allow additional plasma-generated oxidizers to be entrained into the hot combustion products. Planar laser induced incandescence (PLII) diagnostics were performed with laser sheet formed from 532 nm Nd:YAG laser to estimate possible soot reduction effect of MW plasma. A semi-quantitative comparison was made between without-plasma conventional diesel combustion and with-plasma combustion; with LII performed at different jet cross-sections in the combustion chamber.

The objective of this study is to investigate the initial flame propagation characteristics of turbulent flame in an engine cylinder through time-series analysis of radical emissions. A spark plug with optical fiber was developed in this study. The plug sensor is M12 type that makes it possible to mount in practical engine. The spark plug sensor can detect radical emissions in time-resolved spectra through time-series spectroscopic measurement. In this spectra, some kinds of radical emissions such as OH*(306nm), CH*(431nm) and C2*(517nm) based on principle of chemiluminescence are observed. In this study, the spark plug sensor was applied to both compression-expansion machine (CEM) and practical engine. As a result of CEM with bottom viewed high-speed camera, three kinds of spectra could be detected.

Extending the lean limit or/and exhaust-gas-recirculation (EGR) limit/s are necessary for improving fuel economy in spark ignition engines. One of the major problems preventing the engine to operate at lean conditions is stable and successful initial ignition kernel formation. A repeatable, stabilized ignition and early flame development are quite important for the subsequent part of the combustion cycle to run smooth without partial burn or cycle misfire. This study aims to develop an innovative plasma ignition system for reciprocating combustion engines with an aim to extend lean limit and for high pressure applications. This ignition system utilizes microwaves to generate plasma as an ignition source. This microwave plasma igniter is much simplified device compared to conventional spark plug. The microwave plasma ignition system consists of microwave oscillator, co-axial cable and microwave discharge igniter (MDI).

Bio-gas as an internal combustion (I.C.) engine fuel has many advantages such as cheaper fuel cost, low emission levels and especially the neutral recirculation loop of carbon dioxide, which is one of the principal factors in global warming. In this study, positive potentialities of bio-gas were investigated using a micro co-generation engine. The mixing ratio of methane (CH4) and carbon dioxide (CO2) was changed to simulate various types of bio-gases. Intake air and fuel flow rates were controlled to change the equivalence ratio. The engine load condition could be changed with the electric output power used. Base on the result, the higher CO2 content rate slowed down the engine speed in the same load condition and the combustion speed generally decreased under the same load condition with maintaining the engine speed. However thermal efficiency increased with lean burn conditions and NOX emission decreased with higher CO2 mixing rates.

A single cylinder, supercharged dual fuel gas engine with micro-pilot fuel injection is operated using methane only and methane-hydrogen mixtures. Methane only experiments were performed at various equivalence ratios and equivalence ratio of 0.56 is decided as the optimum operating condition based on engine performance, exhaust emissions and operation stability. Methane-hydrogen experiments were performed at equivalence ratio of 0.56 and 2.6 kJ/cycle energy supply rate. Results show that indicated mean effective pressure is maintained regardless of hydrogen content of the gaseous fuel while thermal efficiency is improved and presence of hydrogen reduces cyclic variations. Increasing the fraction of hydrogen in the fuel mixture replaces hydrocarbon fuels and reduces carbon monoxide and hydrocarbon emissions.

Hydrogen spark-ignition (SI) engines based on direct-injection (DI) have been investigated because of their potential for high thermal efficiency and solving the problems related to knocking, backfiring, and pre-ignition. Wide range flammability limits in hydrogen engine enable smooth engine operation for a very lean mixture with low NOX. However, a too lean mixture may increase ignition delay and causes severe cyclic variations. There is a possibility that the turbulence occurred during injection of fuel surround the spark plug in the combustion chamber is major contributor to this phenomenon. To overcome this problem, a better understanding of the spark discharge and spark ignition during transient hydrogen jet is necessary. Therefore, it is very important to study an effect of local equivalence ratio and behavior of spark discharge in SI engine. This paper describes a mixing process of hydrogen jet using spark-induced breakdown spectroscopy (SIBS) in a constant volume vessel.

Hydrogen spark-ignition (SI) engines based on direct-injection (DI) promise significant advantages in terms of thermal efficiency and power output, as well as a means of overcoming problems related to knocking, backfiring, and pre-ignition. In a DI hydrogen engine, the fuel/air mixture is formed by injecting a jet of hydrogen into the air inside the combustion chamber. An Ar-ion laser beam was used as a light source to visualize the hydrogen jet in a constant-volume chamber. This allowed us to study the structure of the jet in addition to other physical processes resulting from hydrogen gas injection. Combustion experiments were conducted in a single-cylinder SI optical research engine equipped with a DI system to detect the early kernel growth assisted by the spark, as well as flame propagation. Various equivalence ratios and fuel injection timings were analyzed to identify the effects on combustion.

The extension of the lean stability limits of gasoline-air mixtures using a microwave-assisted spark plug has been investigated. Experiments are conducted on a 1200 RPM single-cylinder Waukesha Cooperative Fuel Research (CFR) engine at two compression ratios: 7:1 and 9:1; and four different levels of microwave energy input per cycle (prior to accounting for transmission losses): 0 mJ (spark only), 130 mJ, 900 mJ, and 1640 mJ. For various microwave energy inputs, the effects upon stability limits are explored by gradually moving from stoichiometric conditions to increasingly lean mixtures. The coefficient of variation (COVIMEP) of the indicated mean effective pressure (IMEP) is used as an indication of the stability limits. Specific characteristics of microwave-assisted ignition are identified. Microwave enhancement extends stability limits into increasingly lean regions, but slow and partial burning at the leanest mixtures curb efficiency gains.

The combustion and exhaust emissions characteristics of a supercharged dual-fuel natural gas engine with a single cylinder were analyzed. We focused on EGR (Exhaust Gas Recirculation) to achieve higher thermal efficiency and lower exhaust emissions. The combustion of diesel fuel (gas oil) as ignition sources was visualized using a high-speed video camera from the bottom of a quartz piston. The luminous intensity and flame decreased as the EGR rate increased. Furthermore, the ignition delay became longer due to the EGR. Characteristics of the combustion and exhaust emissions were investigated with changing EGR rates under supercharged conditions. The indicated mean effective pressure and thermal efficiency decreased with increasing EGR rate. In addition, NOx emissions decreased due to the EGR. In this study two-stage combustion was observed.

In this study, fuel concentration measurements in a spark-ignition (SI) engine with ethanol blended gasoline were carried out using an optical sensor installed in the spark plug with laser infrared absorption technique. The spark plug sensor for in-situ fuel concentration measurement was applied to a port injected SI engine. The molar absorption coefficients of ethanol blended gasoline were determined for various pressures and temperatures in advance using a constant volume vessel with electric heating system. Ethanol blended gasoline with high volumetric ratios shows lower molar absorption coefficients due to lower molar absorption coefficients of ethanol. The molar absorption coefficients of ethanol blended gasoline can be estimated by considering the molar fraction of each component.

Non-intrusive measurement of transient unburned gas temperatures was developed with a fiber-optic heterodyne interferometry system. Using the value of the Gladstone-Dale constant for DME gas and combustion pressure we can calculate the in-cylinder temperature inside unburned and burned region. In this experimental study, it was performed to set up a fiber-optic heterodyne interferometry technique to measure the temperature before and behind the combustion region in a DME-HCCI engine. At first, measured temperature was almost the same as the temperature history assuming that the process that changes of the unburned and the burned are polytropic. In addition, we measured the temperature after combustion which of condition was burned gas with DME-HCCI combustion. The developed heterodyne interferometry used the spark-plug-in fiber-optic sensor has a good feasibility to measure the unburned and burned temperature history.