Search Results

Recent experimental studies on the behavior of adhesively-bonded steel double-hat section components under axial impact loading have produced encouraging results in terms of load-displacement response and energy absorption when compared to traditional spot-welded hat- sections. However, it appears that extremely limited study has been carried out on the behavior of such components under transverse impact loading keeping in mind applications such as automotive body structures subject to lateral/side impact. In the present work, lateral impact studies have been carried out in a drop-weight test set-up on adhesively-bonded steel double-hat section components and the performance of such components has been compared against their conventional spot-welded and hybrid counterparts. It is clarified that hybrid components in the present context refer to adhesively-bonded hat-sections with a few spot welds only aimed at preventing catastrophic flange separations.

The present work is concerned with the objective of design optimization of an automotive front end structure meeting both occupant and pedestrian safety requirements. The main goal adopted here is minimizing the mass of the front end structure meeting the safety requirements without sacrificing the performance targets. The front end structure should be sufficiently stiff to protect the occupant by absorbing the impact energy generated during a high speed frontal collision and at the same time it should not induce unduly high impact loads during a low speed pedestrian collision. These two requirements are potentially in conflict with each other; however, there may exist an optimum design solution, in terms of mass of front end structure, that meets both the requirements.

Numerical models of Hybrid III had been widely used to study the effect of underbody blast loading on lower extremities. These models had been primarily validated for automotive loading conditions of shorter magnitude in longer time span which are different than typical blast loading conditions of higher magnitude of shorter duration. Therefore, additional strain rate dependent material models were used to validate lower extremity of LSTC Hybrid III model for such loading conditions. Current study focuses on analyzing the mitigating effect of combat boots in injury responses with the help of validated LSTC Hybrid III model. Numerical simulations were run for various impactor speeds using validated LSTC Hybrid III model without any boot (bare foot) and with combat boot.

The present work is concerned with the objective of developing a process for practical multi-disciplinary design optimization (MDO). The main goal adopted here is to minimize the weight of a vehicle body structure meeting NVH (Noise, Vibration and Harshness), durability, and crash safety targets. Initially, for simplicity a square tube is taken for the study. The design variables considered in the study are width, thickness and yield strength of the tube. Using the Response Surface Method (RSM) and the Design Of Experiments (DOE) technique, second order polynomial response surfaces are generated for prediction of the structural performance parameters such as lowest modal frequency, fatigue life, and peak deceleration value. The optimum solution is then obtained by using traditional gradient-based search algorithm functionality “fmincon” in commercial Matlab package.

An attractive strategy for joining metallic as well as non-metallic substrates through adhesive bonding. This technique of joining also offers the functionality for joining dissimilar materials. However, doubts are often expressed on the ability of such joints to perform on par with other mechanical fastening methodologies such as welding, riveting, etc. In the current study, adhesively-bonded single lap shear (SLS), double lap shear (DLS) and T-peel joints are studied initially under quasi-static loading using substrates made of a grade of mild steel and an epoxy-based adhesive of a renowned make (Huntsman). Additionally, single lap shear joints comprised of a single spot weld are tested under quasi-static loading. The shear strengths of adhesively-bonded SLS joints and spot-welded SLS joints are found to be similar. An important consideration in the deployment of adhesively bonded joints in automotive body structures would be the performance of such joints under impact loading.

Multidisciplinary Design Optimization (MDO) is of great significance in the lean design of vehicles. The present work is concerned with the objective of cross-functional optimization (i.e. MDO) of automotive body. For simplicity, the main goal adopted here is minimizing the weight of the body meeting NVH and crash safety targets. The stated goal can be achieved following either of two different ways: classic response surface method (RSM) and practical MDO methodology espoused recently. Even though RSM seems to be able to find a design point which satisfies the constraints, the problem is with the time associated with running such CAE algorithms that can provide a single optimal solution for multi-disciplinary areas such as NVH and crash safety.

Described in this paper is a component test methodology to evaluate the door trim armrest performance in an Insurance Institute for Highway Safety (IIHS) side impact test and to predict the SID-IIs abdomen injury metrics (rib deflection, deflection rate and V*C). The test methodology consisted of a sub-assembly of two SID-IIs abdomen ribs with spine box, mounted on a linear bearing and allowed to translate in the direction of impact. The spine box with the assembly of two abdominal ribs was rigidly attached to the sliding test fixture, and is stationary at the start of the test. The door trim armrest was mounted on the impactor, which was prescribed the door velocity profile obtained from full-vehicle test. The location and orientation of the armrest relative to the dummy abdomen ribs was maintained the same as in the full-vehicle test.

The goal of optimization in vehicle design is often blurred by the myriads of requirements belonging to attributes that may not be quite related. If solutions are sought by optimizing attribute performance-related objectives separately starting with a common baseline design configuration as in a traditional design environment, it becomes an arduous task to integrate the potentially conflicting solutions into one satisfactory design. It may be thus more desirable to carry out a combined multi-disciplinary design optimization (MDO) with vehicle weight as an objective function and cross-functional attribute performance targets as constraints. For the particular case of vehicle body structure design, the initial design is likely to be arrived at taking into account styling, packaging and market-driven requirements.

This paper presents equations that relate the orientation and spacing of yaw mark striations to the vehicle braking and steering levels present at the time the striations were deposited. These equations, thus, provide a link between physical evidence deposited on a roadway during a crash (the tire mark striations) and actions taken by the driver during that crash (steering and braking inputs). This paper also presents physical yaw tests during which striated yaw marks were deposited. Analysis of these tests is conducted to address the degree to which the presented equations can be used to determine a driver’s actual steering and braking inputs. As a result of this testing and analysis, it was concluded that striated tire marks can offer a meaningful glimpse into the steering and braking behavior of the driver of a yawing vehicle. It was also found that consideration of yaw striations allows for the reconstruction of a vehicle’s post-impact yaw motion from a single tire mark.

This paper explores the accuracy of a planar, impulse-momentum impact model in representing the dynamics of three vehicle-to-ground impacts that occurred during a SAE J2114 dolly rollover test. The impacts were analyzed, first, using video analysis techniques to obtain the actual velocity conditions, accelerations, impact force components and the energy loss for each of the impacts. Next, these same impacts were analyzed using the known initial velocity conditions and the subject impact model. The equations of this impact model yielded calculated values for the velocity changes and energy loss for each impact. These calculated results were then compared to the actual dynamics data from the video analysis of the impacts to determine the accuracy of the impact model results. For all three vehicle-to-ground impacts considered in this study, the impact model results for the velocity changes and energy loss showed excellent agreement with the video analysis results for these parameters.

Upper interior head impact safety is an important consideration in vehicle design and is covered under FMVSS 201. This standard generally requires that HIC(d) should not exceed 1000 when a legitimate target in the upper interior of a vehicle is impacted with a featureless Hybrid III headform at a velocity of 15 mph (6.7 m/s). As HIC and therefore HIC(d) is based on translational deceleration experienced at the CG of a test headform, its applicability is often doubted in protection against injury that can be caused due to rotational acceleration of head during impact. A study is carried out here using an improved lumped parameter model (LPM) representing headform impact for cases in which moderate to significant headform rotation may be present primarily due to the geometric configuration of targets.

This paper explores the influence of the impact conditions on the dynamics and the severity of rollover crashes. Causal connections are sought between the impact conditions and the crash attributes to which they lead. The paper begins by extending previously presented equations that describe the dynamics of an idealized vehicle-to-ground impact. It then considers the behavior of these equations under a variety of impact conditions that occur during real-world rollovers. Specifically, the equations of this impact model are used to explore the ways in which and the extent to which rollover dynamics and severity are influenced by the following factors: (1) the vehicle's shape and its orientation at impact, (2) its weight, center-of-mass location, and roll moment of inertia, (3) its translational speed, (4) its downward velocity, and (5) its roll velocity. Throughout this discussion, data from real-world and staged rollover crashes is used to give the parameter study an empirical basis.

This paper examines the use of camera-matching video analysis techniques to quantify the vehicle dynamics and deformation for a dolly rollover test run in accordance with the SAE Recommended Practice J2114. The method presented enables vehicle motion data and deformation measurements to be obtained without the use of the automated target tracking employed by existing motion tracking systems. Since it does not rely on this automated target tracking, the method can be used to analyze video from rollover tests which were not setup in accordance with the requirements of these automated motion tracking systems. The method also provides a straightforward technique for relating the motion of points on the test vehicle to the motion of the vehicle's center-of-mass. This paper, first, describes the specific rollover test that was utilized. Then, the camera-matching method that was used to obtain the vehicle motion data and deformation measurements is described.

Many rollover safety researches have been conducted experimentally and analytically to investigate the underlying causes of vehicle accidents and develop rollover test procedures and test methodologies to help understand the nature of rollover crash events. In addition, electronic and/or mechanical instrumentation are used in dummy and vehicle to measure their responses that allow both vehicle kinematics study and occupant injury assessment. However, method for measurement of dynamic structural deformation needs further exploration, and means to monitor vehicle-to-ground contact load is still lacking. Thus, this paper presents a method for determining the vehicle-to-ground load during laboratory-based rollover tests using results obtained from a camera-matching photogrammetric technology as inputs to a FE SUV model using a nonlinear crash analysis code.

A computational model of a mid-size sport utility vehicle was developed using MADYMO. The model includes a detailed description of the suspension system and tire characteristics that incorporated the Delft-Tyre magic formula description. The model was correlated by simulating a vehicle suspension kinematics and compliance test. The correlated model was then used to simulate a J-turn vehicle dynamics test maneuver, a roll and non-roll ditch test, corkscrew ramp and a lateral trip test, the results of which are presented in this paper. The results indicate that MADYMO is able to reasonably predict the vehicle and occupant responses in these types of applications and is potentially suited as a tool to help setup a suite of vehicle configurations and test conditions for rollover sensor testing. A suspension system sensitivity study is presented for the laterally tripped non-roll event.

This paper explores the dynamics of rollover crashes and examines factors that influence the severity of the roof-to-ground impacts that occur during these crashes. The paper first reports analysis of 12 real-world rollover accidents that were captured on video. Roll rate time histories for the vehicles in these accidents are reported and the characteristics of these curves are analyzed. Next, the paper uses analytical modeling to explore the influence that the trip phase characteristics may have on the severity of roof-to-ground impacts that occur during the roll phase. Finally, the principle of impulse and momentum is used to derive an analytical impact model for examining the mechanics of a roof-to-ground impact. This modeling is used to identify the influence of various impact conditions on the severity of a roof-to-ground impact.

Numerical analyses frequently accompany experimental investigations that study injury biomechanics and improvements in automotive safety. Limited by computational speed, earlier mathematical models tended to simplify the system under study so that a set of differential equations could be written and solved. Advances in computing technology and analysis software have enabled the development of many sophisticated models that have the potential to provide a more comprehensive understanding of human impact response, injury mechanisms, and tolerance. In this article, 50 years of publications on numerical modeling published in the Stapp Car Crash Conference Proceedings and Journal were reviewed. These models were based on: (a) author-developed equations and software, (b) public and commercially available programs to solve rigid body dynamic models (such as MVMA2D, CAL3D or ATB, and MADYMO), and (c) finite element models.

This paper presents an image analysis of a laboratory-based rollover crash test using camera-matching photogrammetry. The procedures pertaining to setup, analysis and data process used in this method are outlined. Vehicle roll angle and rate calculated using the method are presented and compared to the measured values obtained using a vehicle mounted angular rate sensor. Areas for improvement, accuracy determination, and vehicle kinematics analysis are discussed. This paper concludes that the photogrammetric method presented is a useful tool to extract vehicle roll angle data from test video. However, development of a robust post-processing tool for general application to crash safety analysis requires further exploration.

The ability to extract and evaluate the time history of structural deformations or crush during vehicle crashes represents a significant challenge to automotive safety researchers. Current methods are limited by the use of electro-mechanical devices such as string pots and/or linear variable displacement transducers (LVDT). Typically, one end of the transducer must be mounted to a point on the structure that will remain un-deformed during the event; the other end is then attached to the point on the structure where the deformation is to be measured. This approach measures the change in distance between these two points and is unable to resolve any movement into its respective X, Y, or Z directions. Also, the accuracy of electro-mechanical transducers is limited by their dynamic response to crash conditions. The photogrammetry technique has been used successfully in a wide variety of applications including aerial surveying, civil engineering and documentation of traffic accidents.

A number of studies, using data from NASS-CDS, have shown a large percentage of rollover crashes can be classified as tripped events. In many cases, the requirements for a tripped rollover detection algorithm are driven by the timely activation of an occupant containment device. To meet these requirements rollover detection algorithms have been developed by utilizing vehicle roll rate, lateral and vertical accelerations data collected primarily from laboratory tests. This study identifies and examines several challenges associated with developing a rollover detection algorithm with enhanced capabilities. Enhancement of the detection algorithm is explored by considering additional vehicle responses: forward velocity and sideslip angle. With the additional signals, discrimination of rollover crashes from other crash modes is discussed. Potential field/laboratory test modes are proposed to generate the additional vehicle signals.