Search Results

Simultaneous laser induced fluorescence (LIF) imaging of formaldehyde and a fuel-tracer have been performed in a direct-injection HCCI engine. A mix of N-heptane and iso-octane was used as fuel and Toluene as fluorescent tracer. The experimental setup involves two pulsed Nd:YAG lasers and two ICCD cameras. Frequency quadrupled laser radiation at 266 nm from one of the Nd:YAG lasers was used for excitation of the fuel tracer. The resulting fluorescence was detected with one of the ICCD cameras in the spectral region 270-320 nm. The second laser system provided frequency tripled radiation at 355 nm for excitation of Formaldehyde. Detection in the range 395-500 nm was achieved with the second ICCD. The aim of the presented work is to investigate the applicability of utilizing formaldehyde as a naturally occurring fuel marker. Formaldehyde is formed in the low temperature reactions (LTR) prior to the main combustion and should thus be present were fuel is located until it is consumed.

An interest in measuring ion current in Homogeneous Charge Compression Ignition (HCCI) engines arises when one wants to use a cheaper probe for feedback of the combustion timing than expensive piezo electric pressure transducers. However the location of the ion current probe, in this case a spark plug, is of importance for both signal strength and the crank angle position where the signal is obtained. Different fuels will probably affect the ion current in both signal strength and timing and this is the main interest of this investigation. The measurements were performed on a Scania D12 engine in single cylinder operation and ion current was measured at 7 locations simultaneously. By arranging this setup there was a possibility to investigate if the ion current signals from the different spark plug locations would correlate with the fact that, for this particular engine, the combustion starts at the walls and propagates towards the centre of the combustion chamber.

This study applies a state feedback based Closed-Loop Combustion Control (CLCC) using Fast Thermal Management (FTM) on a multi cylinder Variable Compression Ratio (VCR) engine. At speeds above 1500 rpm is the FTM's bandwidth broadened by using the VCR feature of this engine, according to a predefined map, which is a function of load and engine speed. Below 1500 rpm is the PID based CLCC using VCR applied instead of the FTM while slow cylinder balancing is effectuated by the FTM. Performance of the two CLCC controllers are evaluated during an European EC2000 drive cycle, while HC, CO and CO2 emissions are measured online by a Fast Response Infrared (FRI) emission equipment. A load and speed map calculated for an 1.6L Opel Astra is used to get reference values for the dynamometer speed and the load control. The drive cycle test is initiated from a hot engine and hence no cold start is included. Commercial RON/MON 92/82 gasoline, which corresponds to US regular, is utilized.

Combustion initiation in an HCCI engine is dependent of several parameters that are not easily controlled like the temperature and pressure history in the cylinder. So achieving the same ignition condition in all the cylinders in a multi-cylinder engine is difficult. Factors as gas exchange, compression ratio, cylinder cooling, fuel supply, and inlet air temperature can differ from cylinder-to-cylinder. These differences cause both combustion phasing and load variations between the cylinders, which in the end affect the engine performance. Operating range in terms of speed and load is also affected by the cylinder imbalance, since misfiring or too fast combustion in the worst cylinders limits the load. The cylinder-to-cylinder variations are investigated in a multi-cylinder Variable Compression Ratio (VCR) engine, and the effect it has on the engine performance.

Homogenous Charge Compression Ignition (HCCI) is a promising part load combustion concept for future power train applications. Different approaches to achieve and control HCCI combustion are today investigated and compared, especially concerning operating range. The HCCI operating range for vehicle applications should at least cover contemporary emissions drive cycles. The operating range in terms of speed and load is investigated with a Naturally Aspirated (NA) four-stroke multi-cylinder engine with Port Fuel Injection (PFI). HCCI combustion control is achieved with Variable Compression Ratio (VCR) and inlet air preheating with exhaust heat. Both primary reference fuels and commercial gasoline are used in the tests. HCCI combustion with commercial gasoline is achieved over a load range from 0 to 3.6bar BMEP, and over a speed range from 1000 to 5000rpm. Maximum load is at 1000rpm and decreases with an approximately straight slope to zero at 5000rpm.

A 6-cylinder truck engine is modified for turbo charged dual fuel Homogeneous Charge Compression Ignition (HCCI) engine operation. Two different fuels, ethanol and n-heptane, are used to control the ignition timing. The objective of this study is to demonstrate high load operation of a full size HCCI engine and to discuss some of the typical constraints associated with HCCI operation. This study proves the possibility to achieve high loads, up to 16 bar Brake Mean Effective Pressure (BMEP), and ultra low NOx emissions, using turbo charging and dual fuel. Although the system shows great potential, it is obvious that the lack of inlet air pre heating is a drawback at low loads, where combustion efficiency suffers. At high loads, the low exhaust temperature provides little energy for turbo charging, thus causing pump losses higher than for a comparable diesel engine. Design of turbo charger therefore, is a key issue in order to achieve high loads in combination with high efficiency.

The use of water injection in a Homogeneous Charge Compression Ignition (HCCI) engine was experimentally investigated. The purpose of this study was to examine whether it is possible to control the ignition timing and slow down the rate of combustion with the use of water injection. The effects of different water flows, air/fuel ratios and inlet pressures were studied for three different fuels, iso-octane, ethanol and natural gas. It is possible to control the ignition timing in a narrow range with the use of water injection, but to the prize of an increase in the already high emissions of unburned hydrocarbons. The CO emission also increased. The NOx emissions, which are very low for HCCI, decreased even more when water injection was applied. The amount of water used was of the magnitude of the fuel flow.

The major advantages with Homogeneous Charge Compression Ignition, HCCI, is high efficiency in combination with low NOx-emissions. The major drawback with HCCI is the problem to control the ignition timing over a wide load and speed range. Other drawbacks are the limitation in attainable IMEP and relativly high emissions of unburned hydrocarbons. But the use of Exhaust Gas Recycling (EGR) instead of only air, slows down the rate of combustion and makes it possible to use lower air/fuel ratio, which increases the attainable upper load limit. The influence of mixture quality was therefore experimentally investigated. The effects of different EGR rates, air/fuel ratios and inlet mixture temperatures were studied. The compression ratio was set to 18:1. The fuels used were iso-octane, ethanol and commercially available natural gas. The engine was operated naturally aspirated mode for all tests.

The Homogeneous Charge Compression Ignition (HCCI) is the third alternative for combustion in the reciprocating engine. Here, a homogeneous charge is used as in a spark ignited engine, but the charge is compressed to auto-ignition as in a diesel. The main difference compared with the Spark Ignition (SI) engine is the lack of flame propagation and hence the independence from turbulence. Compared with the diesel engine, HCCI has a homogeneous charge and hence no problems associated with soot and NOX formation. Earlier research on HCCI showed high efficiency and very low amounts of NOX, but HC and CO were higher than in SI mode. It was not possible to achieve high IMEP values with HCCI, the limit being 5 bar. Supercharging is one way to dramatically increase IMEP. The influence of supercharging on HCCI was therefore experimentally investigated. Three different fuels were used during the experiments: iso-octane, ethanol and natural gas.