Search Results

It is difficult to reach higher compression ratios of the gasoline engine even though higher compression ratios improve thermal efficiency. One of the barriers is large torque drop led by knocking. Extensive researches to suppress knocking of the gasoline engine have been conducted. It is focused on lowering the temperature of fuel mixture in combustion chamber at compression top dead center (TDC). This paper covers the new valvetrain system to decrease the temperature of exhaust valve bottom (combustion) side. Hollow head and stem sodium filled valve (HHSV) have shown more heat transfer from combustion chamber to valve seat insert and valve guide, and higher thermal conductivity valve seat insert (HVSI) and valve guide (HVG) help to decrease valve temperature lower by higher heat transfer.

End-plates are highly stiff plates that hold together the components composing a fuel cell stack, i.e. Membrane Electrode Assemblies (MEAs), Gas Distribution Layers (GDLs) and bipolar plates, offering sufficient contact pressure between them. The proper contact pressure is required not only to improve energy efficiency of a stack by decreasing ohmic loss but also to prevent leakage of fluids such as hydrogen, air, or coolant. When a fuel cell starts in cold environment, heat generated in a fuel cell stack as a result of electrochemical reactions should not be used much to increase the temperature of endplates but to melt ice inside the stack to prevent ice-blocking and to increase the temperature near the three-phase-boundary on MEAs. However, to satisfy the high stiffness required, massive metallic endplates have been used despite their inferior thermal characteristics: high thermal conductivity and large thermal inertia.

A new exhaust system has been developed to cope with post-SULEV (Super Ultra-Low Emissions Vehicle) regulation by newly designed hardware of exhaust system. This paper will describe the various new technologies used for achieving the post-SULEV standards, such as Conicat (cone-type metal catalyst), dual-wall pipe, pipe-type metal catalyst, ultra thin wall monolith and HC trap system for the improvement of catalyst light-off time. The tested data on 2.0L SULEV vehicle indicate that Conicat(cone-type metal catalyst) and HC trap (hydrocarbon absorbing catalyst) have more positive characteristics, and are expected to show the enhanced HC reduction performance with the optimization of emission system.

This paper describes the development of THC reduction technologies compliant with SULEV regulations. Technologies embodied by the developmental work include improvement of fuel spay atomization, quick warm-up through coolant control shut off, and acceleration of fuel atomization for the fast rise of cylinder head temp inside the water jacket as well as the improvement of combustion state. The technologies likewise entail reduced HC while operating in lean A/F condition during engine warm-up with the cold lean-burn technology, individual cylinder A/F control for improvement of catalytic converting efficiency, aftertreatment such as thin-wall catalyst, HC absorber and EHC and etc., through vehicle application evaluation in cold start. We carried out an experimental as well as a practical study against SULEV regulations, and the feasibility of adopting these items in vehicle was likewise investigated.

It is well known that the EHC (Electrically Heated Catalyst) is very effective for the reduction of cold-start hydrocarbon emissions. To optimize EHC applications for LEVI (Low Emission Vehicle) and ULEV (Ultra Low Emission Vehicle) standards, the effect of heating and secondary air injection on the emission purification efficiency in FTP (Federal Test Procedure) were evaluated with three different EHC system configurations. The exhaust manifold location EHC system in which the EHC with a light-off catalyst is installed near the exhaust manifold, yields 0.038g/mile of THC (Total Hydrocarbon emissions) when the test was performed according to the FFP with an engine-aged condition equivalent to 50,000miles. Therefore, the ULEV standards could be achieved through the system. A new battery system for the EHC and a single battery system for vehicle application were evaluated. Evaluation of the Ni-MH battery for EHC system is included.

In HMC, the fundamental research on the hydrogen fueled engine and vehicle has been carried out. For this engine, solenoid driven injector is used to supply gaseous hydrogen into the cylinder and various operating parameters have been changed to study the combustion characteristics of hydrogen. After these experiments on engine, hydrogen fueled vehicle has been constructed and it is controlled by ECU. The amount of emission from the hydrogen vehicle with stoichiometric operation is less than 1/3 of the ULEV legislation.