Search Results

Understanding the fundamental details of drop/wall interactions is important to improving engine performance. Most of the drop-wall interactions studies are based on the impact of a single drop on the wall. To accurately mimic and model the real engine conditions, it is necessary to characterize spray/wall interactions with different impingement frequencies at a wide range of wall temperatures. In this study, a numerical method, based on Smoothed Particle Hydrodynamics (SPH), is used to simulate consecutive droplet impacts on a heated wall both below and above the Leidenfrost temperature. Impact regimes are identified for various impact conditions by analyzing the time evolution of the post-impingement process of n-heptane drops at different impingement frequencies and wall surface temperatures. For wall temperature below the Leidenfrost temperature, the recoiled film does not leave the surface.

Accurate quantification of 3D shapes of the complex ice structures accreted on wind turbine blades is highly desirable to develop ice prediction models for more accurate prediction of the aerodynamic performance degradation and power reduction due to the ice accretion on wind turbine blades. In the present study, an experimental investigation was conducted to quantitatively characterize the 3D shapes of the ice structures accreted over a DU91-W2-250 wind turbine airfoil model in the Icing Research Tunnel available at Iowa State University (ISU-IRT). A glaze icing condition and a rime icing condition that wind turbines usually experience in winter were duplicated by using ISU-IRT. A high-resolution non-intrusive 3D scanning system was used to make detailed 3D-shape measurements to quantify the complicated ice structures accreted on the wind turbine airfoil model as a function of the ice accretion time.

An explorative study was performed to demonstrate the feasibility of using a novel hybrid anti-/de-icing strategy for aircraft icing mitigation. The hybrid method was developed by combining the electro-thermal heating mechanism and specialized surfaces/coatings with different wettabilities. While an electrical film heater was utilized to provide thermal energy around the leading edge of a NACA0012 airfoil model, two different coating strategies, (i.e., (a). Superhydrophobic coating covering the entire airfoil surface to increase droplets bounce-off and accelerate surface water runback vs. (b). super-hydrophilic coating at the leading edge to increase evaporation area + superhydrophobic coating in downstream to prevent runback refreezing) were proposed and evaluated aiming at maximizing the anti-/de-icing efficiency of the hybrid method.

Many engineering systems operating in a cold environment are challenged by ice accretion, which unfavorably affects their aerodynamics and degrades both their performance and safety. Precise characterization of ice adhesion is crucial for an effective design of ice protection system. In this paper, a fracture mechanics-based approach incorporating single cantilever beam test is used to characterize the near mode-I interfacial adhesion of a typical ice/aluminum interface with different surface roughness. In this asymmetric beam test, a thin layer of ice is formed between a fixed and elastically deformable beam subjected to the applied loading. The measurements showed a range of the interfacial adhesion energy (GIC) between 0.11 and 1.34 J/m 2, depending on the substrate surface roughness. The detailed inspection of the interfacial ice fracture surface, using fracture surface replication technique, revealed a fracture mode transition with the measured macroscopic fracture toughness.

Airborne, marine and ground structures are vulnerable to atmospheric icing in cold weather operation conditions. Most of the ice adhesion-related work have focused on the mechanical ice removal strategies because of practical considerations, while limited literature is available for fundamental understanding of the ice adhesion process. Here, we present a fracture mechanics-based approach to characterize interfacial fracture parameters for the shear behavior of a typical ice/aluminum interface. An experimental framework employing two complementary tests (1) lap shear and (2) shear push-out tests was introduced to assess the mode-II fracture parameters for the selected aluminum/ice interface. Both analytical (shear-lag analysis) and numerical (finite element analysis incorporating cohesive zone method) models were used to evaluate shear fracture parameters.

In the present study, an experimental investigation was conducted to characterize a hot-air-based anti-/de-icing system for the icing protection of aero-engine inlet guide vanes(IGVs). The experimental study was conducted in a unique icing research tunnel available at Iowa State University (i.e., ISU-IRT). A hollowed IGV model embedded with U-shaped hot-air flowing conduit was designed and manufactured for the experimental investigations. During the experiments, while a high-speed imaging system was used to record the dynamic ice accretion or anti-/de-icing process over the surface of the IGV model for the test cases without and with the hot-air supply system being turned on, the corresponding surface temperature distributions on the IGV model were measured quantitatively by using a row of embedded thermocouples.

The electro-thermal method is most commonly used for wind turbine anti-/de-icing. The upmost drawback of such systems is the high power consumption. In the present study, we proposed to use a durable slippery liquid-infused porous surface (SLIPS) to effectively reduce the power requirement of the heating element during the anti-/de-icing process. The explorative study was conducted in the Icing Research Tunnel at Iowa State University (ISU-IRT) with a DU91-W2-250 wind turbine blade model exposed under severe icing conditions. During the experiments, while a high-speed imaging system was used to record the dynamic ice accretion process, an infrared (IR) thermal imaging system was also utilized to achieve the simultaneous surface temperature measurements over the test model.

An experimental study was conducted to investigate the dynamic ice accretion processes on bridge cables with different surface modifications (i.e., 1. Standard plain, 2. Pattern-indented surface, and 3. helical fillets). The icing experiments were performed in the unique Icing Research Tunnel available at Iowa State University (i.e., ISU-IRT). In order to reveal the transient ice accretion processes and the associated aerodynamic loadings on the different cable models under the different icing conditions (i.e., rime vs. glaze), while a high-speed imaging system was used to capture the transient details of the surface water transport and ice accretion over the cable surfaces, a high-accuracy dual-transducer force measurement system was also utilized to measure the aerodynamic loadings acting on the ice accreting cable models.

Structures in cold weather environments are susceptible to atmospheric ice formation. A fracture mechanics based approach is proposed for in situ characterization of the interfacial fracture energy of ice on different substrates. This paper summarizes the development of the experimental and analytical framework to measure the ice adhesion energy, calibrated on static ice. The testing configuration utilizes a shaft-loaded blister test to produce stable crack propagation, from a well-defined pre-crack at the interface of the ice layer and the substrate. Measurements of the fracture energy are taken over a range of ice thicknesses and surface roughnesses. The developed analytical framework to estimate adhesion energy are verified and calibrated via finite element numerical simulation of the proposed geometric configuration and employing cohesive surfaces along the interface to simulate the crack nucleation and propagation process.

Accelerated computational optimization of a diesel engine calibration was achieved by combining Support Vector Regression models with the Particle Swarm Optimization routine. The framework utilized a full engine simulation as a surrogate for a real engine test with test parameters closely resembling a typical 4.5L diesel engine. Initial tests were run with multi-modal test problems including Rastragin's, Bukin's, Ackely's, and Schubert's functions which informed the ML model tuning hyper-parameters. To improve the performance of the engine the hybrid approach was used to optimize the Fuel Pressure, Injection Timing, Pilot Timing and Fraction, and EGR rate. Nitrogen Oxides, Particulate Matter, and Specific Fuel Consumption are simultaneously reduced. As expected, optimums reflect a late injection strategy with moderately high EGR rates.

The impact of fuel droplets on heated surfaces is of great importance in internal combustion engines. In engine computational fluid dynamics (CFD) simulations, the drop-wall interaction is usually considered by using models derived from experimental data and correlations rather than direct simulations. This paper presented a numerical method based on smoothed particle hydrodynamics (SPH), which can directly simulate the impact process of fuel droplets impinging on solid surfaces. The SPH method is a Lagrangian meshfree particle method. It discretizes fluid into a number of SPH particles and governing equations of fluid into a set of particle equations. By solving the particle equations, the movement of particles can be obtained, which represents the fluid flows. The SPH method is able to simulate the large deformation and breakup of liquid drops without using additional interface tracking techniques.

The objective of this work was to identify methods of reliably predicting optimum operating conditions in an experimental compression ignition engine using multiple injections. Abstract modeling offered an efficient way to predict large volumes data, when compared with simulation, although the initial cost of constructing such models can be large. This work aims to reduce that initial cost by adding knowledge about the favorable network structures and training rules which are discovered. The data were gathered from a high pressure common rail direct injection turbocharged compression ignition engine utilizing a high EGR configuration. The range of design parameters were relatively large; 100 MPa - 240 MPa for fuel pressure, up to 62% EGR using a modified, long-route, low pressure EGR system, while the pilot timing, main timing, and pilot ratio were free within the safe operating window for the engine.

The International Space Station (ISS) Environmental Control and Life Support (ECLS) system includes regenerative and non-regenerative technologies that provide the basic life support functions to support the crew, while maintaining a safe and habitable shirtsleeve environment. This paper provides a summary of the U.S. ECLS system activities over the past year, covering the period of time between March 2008 and February 2009. The ISS continued permanent crew operations, with the continuation of Phase 3 of the ISS Assembly Sequence. Work continues on the last of the Phase 3 pressurized elements and the continued manufacturing and testing of the regenerative ECLS equipment.

The Crew Exploration Vehicle (CEV) is the first crew transport vehicle to be developed by the National Aeronautics and Space Administration (NASA) in the last thirty years. The CEV is being developed to transport the crew safely from the Earth to the International Space Station and then later, from the Earth to the Moon . This year, the vehicle continued to go through design refinements to reduce weight, meet requirements, and operate reliably while preparing for Preliminary Design Review in the summer of 2009. The design of the Orion Environmental Control and Life Support (ECLS) system, which includes the life support and active thermal control systems, is progressing through the design stage. This paper covers the Orion ECLS development from April 2008 to April 2009.

A work envelope has been defined for weightless Extravehicular Activity (EVA) based on the Space Shuttle Extravehicular Mobility Unit (EMU), but there is no equivalent for planetary operations. The weightless work envelope is essential for planning all EVA tasks because it determines the location of removable parts, making sure they are within reach and visibility of the suited crew member. In addition, using the envelope positions the structural hard points for foot restraints that allow placing both hands on the job and provides a load path for reacting forces. EVA operations are always constrained by time. Tasks are carefully planned to ensure the crew has enough breathing oxygen, cooling water, and battery power. Planning first involves computers using a virtual work envelope to model tasks, next suited crew members in a simulated environment refine the tasks.

Parallel computing schemes were developed to enhance the computational efficiency of engine spray simulations with adaptive mesh refinement (AMR). Spray simulations have been shown to be grid dependent and thus fine mesh is often used to improve solution accuracy. In this study, dynamic mesh refinement adaptive to spray region was developed and parallelized in KIVA-4. The change of cell and node numbers and the local characteristics in the dynamic mesh refinement posed difficulties in developing efficient parallel computing schemes to achieve low communication overhead and good load balance. The present strategy executed AMR on one processor with data scattering among processors following the adaptation, and performed AMR every ten computational timesteps for enhanced parallel performance. The re-initialization was required and performed at the minimized cost.

This paper will provide an overview of the International Space Station (ISS) Environmental Control and Life Support (ECLS) design of the Node 1 Fire Detection and Suppression (FDS) subsystem and it will document some of the lessons that have been learned to date for this subsystem.

At present, spacecraft water quality is assessed when samples collected on the International Space Station (ISS) are returned to Earth. Several months, however, may pass between sample collection and analysis, potentially compromising sample integrity by risking degradation. For example, iodine and silver, which are the respective biocides used in the U.S. and Russian spacecraft potable water systems, must be held at levels that prevent bacterial growth, while avoiding adverse effects on crew health. A comparable need exists for the detection of many heavy metals, toxic organic compounds, and microorganisms. Lead, cadmium, and nickel have been found, for instance, in the ISS potable water system at amounts that surpass existent requirements. There have been similar occurrences with hazardous organic compounds like formaldehyde and ethylene glycol. Microorganism counts above acceptable limits have also been reported in a few instances.

The International Space Station (ISS) Node 1 Environmental Control and Life Support (ECLS) System is comprised of five subsystems: Atmosphere Control and Supply (ACS), Atmosphere Revitalization (AR), Fire Detection and Suppression (FDS), Temperature and Humidity Control (THC), and Water Recovery and Management (WRM). This paper provides a summary of the Node 1 ECLS WRM subsystem design and a detailed discussion of the ISS ECLS Acceptance Testing methodology utilized for that subsystem.

With the long anticipated change to increase the International Space Station (ISS) crew size from three to six crew members and the retirement of the Space Shuttle, changes are in work to the International Space Station (ISS) Environmental Control and Life Support (ECLS) System to support the increased on-orbit crew size and their continued operations. The Space Shuttle had provided high pressure oxygen resupply, high pressure nitrogen resupply, water resupply, atmosphere gaseous make up when the Space Shuttle is docked to ISS, and logistic cargo supply/return capability to ISS. Without the Space Shuttle additional changes need to be made to the ISS ECLS System to support the six crew members post Assembly Complete (AC). This will be in addition to the changes that were needed to support doubling the nominal ISS crew size from three to six crew members.