Search Results

Many powertrain structural sub-systems are often tested under steady state conditions on a dynamometer or in a full vehicle. This process (while necessary) is costly and time intensive, especially when evaluating the effect of component properties on transient phenomena, such as driveline clunk. This paper proposes a laboratory experiment that provides the following: 1) a bench experiment that demonstrates transient behavior of a non-linear clutch damper under non-rotating conditions, 2) a process to efficiently evaluate multiple non-linear clutch dampers, and 3) generates benchmark time domain data for validation of non-linear driveline simulation codes. The design of this experiment is based on a previous experimental work on clunk. A commercially available non-linear clutch damper is selected and the experiment is sized accordingly. The stiffness and hysteresis properties of the clutch damper are assumed from the measured quasi-static torque curve provided by the manufacturer.

Torsional stiffness properties were developed for both a 53-foot box trailer and a 28-foot flatbed control trailer based on experimental measurements. In order to study the effect of torsional stiffness on the dynamics of a heavy truck vehicle dynamics computer model, static maneuvers were conducted comparing different torsional stiffness values to the original rigid vehicle model. Stiffness properties were first developed for a truck tractor model. It was found that the incorporation of a torsional stiffness model had only a minor effect on the overall tractor response for steady-state maneuvers up to 0.4 g lateral acceleration. The effect of torsional stiffness was also studied for the trailer portion of the existing model.

This paper presents a concept for enhancing catalytic removal of pollutant species from an exhaust stream by placing placing the plasma adjacent to the catalyst surface. Model calculations of the behavior of the electron energy distribution function (EEDF), which influences the chemistry and ionization levels near the surface, are performed and analyzed. Preliminary experiments attempting to reduce these theoretical ideas to practice in N2/NO mixtures, are discussed. Although removal of NO is observed, this is due to gas phase effects alone. The present experimental arrangement is not able to produce the requisite conditions outlined by theory to enact plasma-enhanced catalysis.

One obstacle hindering the use of port fuel injection in natural gas engines is poor idle performance due to incomplete mixing of the cylinder charge prior to ignition. Fuel injection timing has a strong influence on the mixing process. The purpose of this work is to determine the impact of fuel injection timing on in-cylinder fuel distribution. Equivalence ratio maps have been acquired by Planar Laser Induced Fluorescence in an optical engine with a production cylinder head. Experimental results have been used to determine the injection timing which produces the most uniform fuel distribution for the given engine.

Welding residual stress is one of the primary factors responsible for cracking at the access hole interface between the flange and web plate of welded heavy W-shapes. During multi-pass welding, cracks can be found in either the flange plate or the web plate, depending upon welding sequence, joint details and access hole size. In this study, an integrated numerical and experimental investigation was conducted to evaluate the effects of welding parameters and joint geometry on the magnitude and distribution of residual stresses in thick-section butt joints. The results provide guidelines for improved design for welding of heavy W-shapes.

The soil response to traffic loads as affected by tire inflation pressure, track width and drawbar pull was measured. The change in soil physical properties caused by a John Deere 8870 tractor at two tire pressure settings and CATERPILLAR Challenger 65 and 75 tractors with 64 and 89 cm wide belt tracks, were measured at two load levels; no draft (tractor only) and tractor pulling a 12.5 m field cultivator. The Ohio State University Soil Physical Properties Measurement System was used to measure cone penetration resistance, air permeability, air-filled porosity, and bulk density. The results show the dual overinflated tires caused the greatest change, followed by the CATERPILLAR Challenger 65 track, then the CATERPILLAR Challenger 75 track, and finally dual correctly inflated tires caused the least effect on soil physical properties. These results were consistent at each depth. The effects of the two draft levels give the same ranking of the tractive units.

A mathematical basis for predicting loaded off-line of action contact at the tips of undermodified gear teeth is discussed. Two methods of solving the contact problem, using a modified simplex algorithm, are used to predict the load distribution. The methods differ in the compliance matrix formulation and the way they search for contact. The first method uses a tapered plate model and the second method uses a finite element model. The effects of off-line of action contact on load sharing, effective contact ratio and motion curves are shown.

The state of Ohio has recognized the importance and potential impact of Intelligent Vehicle-Highway Systems (IVHS) to its citizens and business enterprises. In response to the identified need, a small group of individuals representing Federal and state government, academia, and the private sector have worked together over the past year to initiate a statewide IVHS effort. This initiative is referred to as IVHS~Ohio. The objective of the effort is to "coordinate and foster a public, private, and academic partnership to make the urban and rural surface transportation system in the state of Ohio significantly safer, more effective, and more efficient by accelerating the identification, development, integration, and deployment of IVHS technologies." A May 1993 symposium was attended by over 220 people from government, academia, and the private sector. The result was a unanimous decision to establish a statewide IVHS program.

Improper roll pass designs can lead to either underfill which results in the formation of hairline cracks on the surface of the finished bars or overfill which results in roll overloading and the formation of fins. Therefore to reduce downtime, and improve yield and quality, it becomes important to design an acceptable roll pass in reasonable time. This paper presents a methodology for roll pass design which uses a three dimensional finite element technique along with an empirical procedure to arrive at an iterative scheme for reducing the number of passes and improving metal flow in the passes. This methodology is applied to improving an existing seven pass square - to - round rolling sequence, resulting in the reduction of the number of passes and improved distributions of effective strains in the rolled product.

The objective of this paper is to develop a self-tuning optimal control of an active suspension. An active suspension composed of an identifier and a controller is proposed in this paper. Although control strategies on active (or semi-active) suspensions have been investigated during the past few decades, some problems are not well understood yet. One of them arising from the ride control of an active suspension is that when the weight and the moments of inertia of the sprung mass are varied, the feedback gains of the controller should vary with the variation of parameters accordingly. Therefore, the identifier is proposed before the controller is designed. In the real situations, the parameter variation may occur when loadings on vehicles vary - either from passengers or payloads, especially, in the case of loading on a truck. An identification structure using parallel model reference adaptive system (MRAS) is proposed to identify the true parameters.