Search Results

In-cylinder sampling appears to be the only available means for obtaining detailed information of the diesel combustion process. This information is necessary to understand pollutant formation because of the intimate relationship between formation rates and local cylinder conditions. This paper discusses efforts to (1) examine and improve sampling valve design, (2) evaluate potential effects of the valve and the sampling system on sample composition, (3) find methods to extract useful information from sampling data. Sampling hardware is currently being used to study combustion in engines, but further work is needed to quantify the influence of hardware and procedures on sample composition and to design experiments to provide data containing maximum information.

A single-wheel trailer has been designed and built to study the origins of tire noise and its basic characteristics. The single test tire, nominally the 10.00/20 size usually mounted on large trucks and semitrailers, is located 12.2 m (40 ft) behind the rear axle of the towing vehicle to isolate it from other noise sources. Reflective surfaces that could interfere with noise measurements are minimized by the high, single-beam construction of the trailer. The towing vehicle is modified to reduce its noise and wake in the vicinity of the test tire, which can be loaded to 22.2 kN (5000 lb) by dead weights and rolled at expressway speeds. Because of its unusual configuration, the dynamic behavior of the trailer was studied prior to design to help determine several design parameters and show that the trailer would follow well. Extensive stress analyses of the trailer beam and other structural elements were also required.

During development of the General Motors rotary engine, the lubricant was recognized as important to its success because certain lubricants produced deposits which tended to stick both side and apex seals. Consequently, it was decided to develop a rotary engine-dynamometer test, using a Mazda engine, which could be used for lubricant evaluation. In an investigation using an SE engine oil with which there was rotary engine experience, engine operating variables and engine modifications were studied until the greatest amount of deposits were obtained in 100 h of testing. The most significant engine modifications were: omission of inner side seals, plugging of half the rotor bearing holes, pinning of oil seals, grinding of end and intermediate housings, and using a separate oil reservoir for the metering pump. Using this 100 h test procedure, three engine oils and five automatic transmission fluids were evaluated.

Automatic transmission fluids can oxidize with use, causing marginal transmission performance and eventual transmission malfunction. Periodic fluid changes are presently recommended to alleviate this problem. Fluid oxidation is promoted in current transmissions because they breathe air freely through a vent tube. To reduce fluid oxidation, and thereby improve fluid and transmission durability, a one-way check valve, called the Transmission Air Breathing Suppressor (TABS), was designed to restrict the intake of air into the transmission and to replace the conventional vent tube. The effectiveness of the TABS valve in reducing fluid oxidation was determined in high temperature transmission cycling tests and in taxicab tests. Fluid oxidation results with the TABS valve-equipped transmissions were compared to those with normally-vented transmissions. By reducing the amount of oxygen in the transmission gas, the TABS valve nearly eliminated fluid oxidation.

The assembly and particularly the reduction of the mass and stiffness matrix for a large system can be a significant portion of the computational cost of finding the mode shapes and natural frequencies. Therefore, parameter studies for design purposes can be prohibitive if these matrices are reassembled and reduced for each change. The purpose of this paper is to outline the procedure for using the modes of the original system to determine the dynamic characteristics of the changed system. The method also results in computational savings for boundary condition changes and for large systems that are nearly-symmetric except for a few mass and stiffness changes. To illustrate the method several changes are made to a ladder frame. The results from an analysis using the reconstructed mass and stiffness matrices and the modal synthesis technique are compared to show the accuracy and freedom requirements.

Noise produced by automotive ignition systems can deteriorate the performance of nearby communication systems. An important step toward alleviating this difficulty is to characterize the ignition noise. Measurements have been made of the noise peak amplitude distribution of a number of identically equipped vehicles over a fixed period of time. Both vertical and horizontal polarizations were used, and measurements were made at two frequencies, 145 and 230 MHz. These statistics were then compared to various probability distributions to attempt to characterize the amplitude distribution of the noise. The distributions studied were: the log-normal, the exponential, the Rayleigh, and the Weibull distributions. It was concluded that the best fit was provided by the Weibull distribution. The parameters of the best fitting distribution are primarily a function of the antenna's polarization, with frequency having only a minor effect.

This paper evaluates the tendency of lip seals to fracture in a test apparatus in which dynamic runout is 0.010 in and the temperature is cycled between -30 and 0 F. Seals made of eight different polyacrylate polymers were soap-sulfur cured with various types and amounts of carbon black. Physical tests included room-temperature flexibility defined by Young's modulus at small strains, standard tensile tests at room temperature, flexibility at sub-zero temperatures determined by a Gehman test, and sub-zero starting torques of the seals. Primary determinant of successful fracture resistance is a low starting torque resulting from good low-temperature flexibility. The effect of adding graphite to some of these formulations is described and some current commercially available seals are evaluated.

An analysis of oil pumpability reveals that engine oil pumping failures may occur because either the oil cannot flow under its own head to the oil screen inlet, or the oil is too viscous to flow through the screen and inlet tube fast enough to satisfy pump demands. To determine which factor is controlling, the behavior of commercial, multigraded oils was observed visually at temperatures from -40 to 0°F (-40 to - 17.8°C) in a laboratory oil pumpability test apparatus. Test results revealed that pumping failures occur by the first alternative: a hole is formed in the oil, and the surrounding oil is unable to flow into the hole fast enough to satisfy the pump. Of 14 oils tested, 7 failed to be pumped because of air binding or cavitation which developed in this manner. A model, which explains these failures in terms of yield point considerations and the low shear apparent viscosity of the oils, is proposed.

Platinum, palladium, and copper-chromium oxidation catalysts for exhaust emission control were exposed to exhaust gases from a steady-state engine dynamometer test in which the amount of oil consumed per unit volume of catalyst was high. When unleaded gasoline (0.004 Pb g/gal, 0.004 P g/gal) was used, conventional SE oil caused somewhat greater loss of catalyst activity than an ashless and phosphorus-free (“clean”) oil. Chemical analysis of the catalyst indicated that phosphorus from the conventional oil was probably responsible for the difference. However, a test run with low-lead (0.5 Pb g/gal, 0.004 P g/gal) gasoline and “clean” oil caused much greater catalyst activity deterioration than either of the tests with unleaded gasoline.

The incentive for use of an interstage diffuser in a free-shaft gas turbine engine is briefly examined and some pertinent published background data reviewed. Tests of two annular diffusers behind an upstream turbine show the deleterious effects of turbine exit flow nonuniformity on diffuser behavior. The flow acceleration provided by the area contraction of a power turbine nozzle located at the diffuser exit substantially improves the nature of the flow previously found to exist at the diffuser exit in the absence of the nozzle.

Future low emissions engines will burn unleaded gasoline. Compared with engines of 1970, future engines will have lower concentrations of NOx in the blowby gases, and lower blowby flow-rates; however, oil temperatures will probably be unchanged. The consequences of these conditions for engines using high quality (SE) oils at current drain intervals are: virtual elimination of rust, reduction of sludge, no effect on wear and oil thickening, and possible worsening of varnish. Therefore, extension of the drain interval with SE engine oils in the future may be possible, but final decisions will depend on the findings of research in the areas of engine wear and varnish, and oil thickening.

The use of multigrade (V.I. improved) oils in automotive engines has increased significantly in recent years. However, the performance of these oils in terms of factors such as oil economy, wear, and noise, is not always equal to that of single grade oils. Although the initial viscosity of multigrade oils is related to both the base oil and the V.I. improver, the viscosity decreases with use, with the primary factors determining the magnitude of the change being the degree of shear and the characteristics and concentration of the V.I. improver used. This decrease in viscosity has been assumed to be the cause of the decreases in oil economy that may occur with oil use. However, viscosity changes are not believed to be the primary factor responsible since similar oil economy changes have also been observed for single grade oils. Nevertheless, the characteristics and concentration of the V.I. improver used can be a significant factor influencing oil economy.

Utilization of numerically controlled milling has been found particularly attractive in producing, in limited quantities, the three-dimensional curved surfaces characteristic of turbomachinery. In experimental and developmental programs its use can result in decreased fabrication cost, reduced lead time, and improved dimensional accuracy. Following a review of the general classifications of numerically controlled milling machines available for manufacture of such parts, illustrations are given of some of the procedures and techniques employed in their use. A variety of parts made using numerical control serve as examples.

Tests were conducted using older model cars with automatic transmissions to determine the effect of fluid composition on leakage past the rotating shaft seals. It was found that seal leakage was reduced or stopped by changing to seal-swelling fluids, and increased with seal-shrinking fluids. Leakage was also reduced by adding aromatic additives to existing fluids in the transmissions. Seal volume and hardness change results from bench tests support the car data.

The Total Immersion Test (ASTM D 471) for seal elastomers, used in evaluating the compatibility of fluids and seals for automatic transmissions, does not, produce hardness and volume change results similar to those found for rotating shaft seals in service. The Tip Cycle Test was devised to provide better agreement with service results. In the test, one side of the seal is exposed to air, and the other alternately to fluid and to air-fluid vapor. Rotating shaft seals were evaluated in both car and dynamometer transmission tests, and in various bench tests. Agreement was poor between transmission tests and both the Total Immersion and the Dip Cycle Tests. Good agreement was found with the Tip Cycle Test.

Effective performance of functional automotive components requires fluid sealing under compatible conditions. One method of determining this compatibility is through the use of immersion testing under a variety of conditions that simulate those experienced in actual use. By measuring the changes in the physical properties of the seal materials after immersion a judgment can be made regarding seal/fluid compatibility which will be encountered later in actual use. A series of immersion tests using representative seal materials and automotive fluids; namely, gear oils, transmission fluids, and motor oils were conducted within the framework of the Technical Committee on Automotive Rubber, jointly sponsored by SAE-ASTM.

Conventional radial lip oil seals can be made more effective by utilizing helical grooving beneath the contact lip surface. Miniature hydrodynamic pumps so formed aid the radial lip seal in containing the oil by generating fluid forces opposite in direction to the leakage flow forces. This seal-shaft combination has been termed the Hydroseal. Four factorial experiments were conducted to evaluate the effect of helix angle, groove depth, groove width, and number of grooves on sealing performance. The criterion used as a basis for selecting the optimum design were leakage, wear, hardening of the sealing surface, and pumping capacity. These data indicated that the best hydroseal design was one with three grooves, 0.0003 in. deep, 0.014 in. wide, having a helix angle of 45 deg.

The Sealometer is used for evaluating the performance of lip type oil seals and provides a dimensionless number derived from measuring the increase in temperature of a test shaft operating in a lip seal for a given time interval. With the Sealometer it is possible to study parameters that affect seal performance. As a quality control instrument, the machine provides accurate data for design. Sealometer evaluation offers a quick method of determining the life expectancy of a particular design for a particular application and eliminates the need for long life test programs.

Engine oil test Sequences IIA and IIIA have been developed to replace Sequences I, II, and III. These new sequences are designed to evaluate lubricants for use in current passenger car engines under severe (MS) service conditions. Lubricant performance is evaluated with respect to scuffing wear, rust, corrosion, deposits, and rumble. The Sequence IIA and IIIA test procedure involves major changes which affect the evaluation of engine rusting and provides improved correlation between test results and short-trip service. Average engine rust ratings correlate with service data within ±0.5 numbers. The new test also provides better repeatability and reproducibility in a significantly shorter schedule. The rust repeatability and reproducibility is less than ±0.2 and ±0.6 numbers, respectively. Test time has been reduced 52%.

Tire nonuniformities are a major source of vibration problems in vehicles. There is considerable disagreement on which tire uniformity parameters are important to vehicle noise and vibration problems, and on how these uniformity parameters should be measured. This paper is concerned primarily with the effects of the nonuniformities of the tire structure which cause contact patch force variations as the tire is rolled in a straight line at constant axle height. Experimental results showing the effects of mean radial load and roll size on these structural, or static, nonuniformities are presented which indicate that these force variations should be measured on a large roll at rated load. Mathematical analyses of certain vehicle vibrations show that radial and lateral force variation are important uniformity parameters. The amplitude of the first harmonic of these force variations contributes to vehicle shake.