Search Results

Injector nozzle deposits can have a profound effect on particulate emissions from vehicles fitted with Gasoline Direct Injection (GDI) engines. Several recent publications acknowledge the benefits of using Deposit Control Additives (DCA) to maintain or restore injector cleanliness and in turn minimise particulates, but others claim that high levels of DCA could have detrimental effects due to the direct contribution of DCA to particulates, that outweigh the benefits of injector cleanliness. Much of the aforementioned work was conducted in laboratory scenarios with model fuels. In this investigation a fleet of 7 used GDI vehicles were taken from the field to determine the net impact of DCAs on particulates in real-world scenarios. The vehicles tested comprised a range of vehicles from different manufacturers that were certified to Euro 5 and Euro 6 emissions standards.

It is useful for research purposes to define simple surrogate gasoline compositions that can replicate the chemical and physical properties of more complex mixtures. Ethanol is used in commercially available gasolines around the world as part of the pathway to the decarbonization of the transportation sector. In this study equations were developed to predict the Research Octane Number (RON), Motor Octane Number (MON) and Dry Vapour Pressure Equivalent (DVPE) of gasoline surrogates containing ethanol (10-25 vol%), isopentane, n-heptane, isooctane and toluene. The non-linear blending behaviour associated with ethanol is found to necessitate coefficients in the equations developed for MON that are a function of ethanol content, whereas surprisingly the equations for RON and DVPE do not need this added level of complexity.

Design efforts to improve the hydraulic efficiency of high-pressure diesel fuel systems and thus further improve overall engine efficiency have resulted in the utilisation of low-spill control valves and reduced injector component clearances to reduce general leakage losses. Overall, these advances have contributed significantly to the high efficiency diesel engines of today. However, the combination of very high fuel pressures, cavitation and low fuel leakage volumes increases the heating of the remaining fuel, increasing temperature and, in turn, the propensity for deposits to form inside the injector. This deposit phenomenon is commonly known as Internal Diesel Injector Deposits (IDID) and can cause rough engine running and failed engine starts requiring injector cleaning or replacement. Methods studying this phenomenon are under development in the industry.

Fuel with higher octane content is playing a key role in optimising engine performance by allowing a more optimal spark timing which leads to increased engine efficiency and lower CO2 emissions. In a previous study the impact of octane was investigated with a fleet of 20 vehicles using market representative fuels, varying from RON 91 to 100. The resulting data showed a clear performance and acceleration benefit when higher RON fuel was used. In this follow-up study 10 more vehicles were added to the database. The vehicle fleet was extended to be more representative of Asian markets, thus broadening the geographical relevance of the database, as well as adding vehicles with newer technologies such as boosted down-sized direct injection engines, or higher compression ratio engines. Eight different fuel combinations varying in RON were tested, representing standard gasoline and premium gasoline in different markets around the world.

Improved fuel economy is increasingly a key measure of performance in the automotive industry driven by market demands and tighter emissions regulations. Within this environment, one way to improve fuel economy is via fuel additives that deliver friction- reducing components to the piston-cylinder wall interface. Whilst the use of friction modifiers (FMs) in fuel or lubricant additives to achieve fuel economy improvements is not new, demonstrating the efficacy of these FMs in vehicles is challenging and requires statistical design together with carefully controlled test conditions. This paper describes a bespoke, efficient, high-precision vehicle testing procedure designed to evaluate the fuel economy credentials of fuel-borne FMs. By their nature, FMs persist on engine surfaces and so their effects are not immediately reversible upon changing to a non FM-containing fuel (“carryover” effect), therefore requiring careful design of the test programme.

In Europe, the development and implementation of new regulatory test procedures including the chassis dynamometer (CD) based World Harmonised Light Duty Test Procedure (WLTP) and the Real Driving Emissions (RDE) procedure, has been driven by the close scrutiny that real driving emissions and fuel consumption from passenger cars have come under in recent times. This is due to a divergence between stated certification performance and measured on-road performance, and has been most pointed in the case of NOx (oxides of nitrogen) emissions from diesel cars. The RDE test is certainly more relevant than CD test cycles, but currently certification RDE cycles will not necessarily include the most extreme low speed congested or low temperature conditions which are likely to be more challenging for NOx after-treatment systems.

It is anticipated that worldwide energy demand will approximately double by 2050, whilst at the same time, CO2 emissions need to be halved. Therefore, there is increasing pressure to improve the efficiency of all machines, with great focus on improving the fuel efficiency of passenger cars. The use of downsized, boosted, gasoline engines, can lead to exceptional fuel economy, and on a well-to-wheels basis, can give similar CO2 emissions to electric vehicles (depending, of course, on how the electricity is generated). In this paper, the development of a low weight concept car is reported. The car is equipped with a three-cylinder 0.66 litre gasoline engine, and has achieved over 100 miles per imperial gallon, in real world driving conditions.

Low Temperature Combustion using compression ignition may provide high efficiency combined with low emissions of oxides of nitrogen and soot. This process is facilitated by fuels with lower cetane number than standard diesel fuel. Mixtures of gasoline and diesel (“dieseline”) may be one way of achieving this, but a practical concern is the flammability of the headspace vapours in the vehicle fuel tank. Gasoline is much more volatile than diesel so, at most ambient temperatures, the headspace vapours in the tank are too rich to burn. A gasoline/diesel mixture in a fuel tank therefore can result in a flammable headspace, particularly at cold ambient temperatures. A mathematical model is presented that predicts the flammability of the headspace vapours in a tank containing mixtures of gasoline and diesel fuel. Fourteen hydrocarbons and ethanol represent the volatile components. Heavier components are treated as non-volatile diluents in the liquid phase.

Precise, repeatable and representative testing is a key tool for developing and demonstrating automotive fuel and lubricant products. This paper reports on the first findings of a project that aims to determine the requirements for highly repeatable test methods to measure very small differences in fuel economy and powertrain performance. This will be underpinned by identifying and quantifying the variations inherent to this specific test vehicle, both on-road and on Chassis Dynamometer (CD), that create a barrier to improved testing methods. In this initial work, a comparison was made between on-road driving, the New European Drive Cycle (NEDC) and World harmonized Light-duty Test Cycle (WLTC) cycles to understand the behavior of various vehicle systems along with the discrepancies that can arise owing to the particular conditions of the standard test cycles.

The effects of lubricant oil and fuel properties on low speed pre-ignition (LSPI) occurrence in boosted S.I. engines were experimentally evaluated with multi-cylinder engine and de-correlated oil and fuel matrices. Further, the auto-ignitability of fuel spray droplets and evaporated homogeneous fuel/oil mixtures were evaluated in a combustion bomb and pressure differential scanning calorimetry (PDSC) tests to analyze the fundamental ignition process. The work investigated the effect of engine conditions, fuel volatility and various lubricant additives on LSPI occurrence. The results support the validity of aspects of the LSPI mechanism hypothesis based on the phenomenon of droplets of lubricant oil/fuel mixture (caused by adhesion of fuel spray on the liner wall) flying into the chamber and autoigniting before spark ignition.

This study investigates the effects of octane quality on the performance, i.e., acceleration and power, and fuel economy (FE) of one late model US vehicle, which is powered by a small displacement, turbocharged, gasoline direct injection (GDI) engine. The relative importance of the gasoline parameters Research and Motor Octane Number (RON and MON) in meeting the octane requirement of this engine to run at an optimum spark timing for the given demand was considered by evaluating the octane index (OI), where OI = (1-K) RON + K MON and K is a constant depending on engine design and operating conditions. Over wide open throttle (WOT) accelerations, the average K of this Pontiac Solstice was determined as −0.75, whereby a lower MON would give a higher OI, a higher knock resistance and better performance.

Deposits forming in the injector nozzle holes of modern diesel cars can reduce and disrupt the fuel injected into the combustion chamber, causing reduced or less efficient combustion, resulting in power loss and increased fuel consumption. A study of the factors affecting injector nozzle tip temperature, a parameter critical to nozzle deposit formation, has been conducted in a Peugeot DW10 passenger car bench engine, as used in the industry standard CEC F-098 injector nozzle deposit test, [1]. The findings of the bench engine study were applied in the development of a Chassis Dynamometer (CD) based vehicle test method using Euro 5 compliant vehicles. The developed test method was refined to tune the conditions as far as practicable towards a realistic driving pattern whilst maintaining sufficient deposit forming tendency to enable test duration to be limited to a reasonable period.

The demonstration benefit from fuel-borne fuel-economy additives to a precision of 1%, or better, traditionally requires very careful experimental design and considerable resource intensity. In practice, the process usually requires the use of well-defined drive cycles (e.g. emission certification cycles HFET, NEDC) in conjunction with environmentally-controlled chassis dynamometer facilities. Against this background, a method has been developed to achieve high-precision fuel economy comparison of gasoline fuels with reduced resource intensity and under arbitrary real-world driving conditions. The method relies upon the inference of instantaneous fuel consumption via the collection of OBD data and the simultaneous estimation of instantaneous engine output from vehicle dynamical behaviour.

Laminar burning velocity is a fundamental combustion property of any fuel/air mixture. Formulating gasoline fuel blends having faster burning velocities can be an effective strategy for enhancing engine and vehicle performance. Formulation of faster burning fuels by changing the fuel composition has been explored in this work leading to a clear correlation between engine performance and fuel burning velocity. In principle a gasoline vehicle should be calibrated to give optimal ignition timing (also known as MBT - minimum spark advance for best torque) while at the same time avoiding any possible engine knock. However, modern downsized/boosted engines frequently tend to be limited by knock and the spark timing is retarded in respect of the optimum. In such scenarios, faster burning fuels can lead to a more optimum combustion phasing resulting in a more efficient energy transfer and hence a faster acceleration and better performance.

A predictive model for estimating the fuel saving of “top tier” engine, axle and transmission lubricants (compared to “mainstream” lubricants), in a heavy duty truck, operating on a realistic driving cycle, is described. Simulations have been performed for different truck weights (10, 20 and 40 tonnes) and it was found that the model predicts percentage fuel economy benefits that are of a similar magnitude to those measured in well controlled field trials1. The model predicts the percentage fuel saving from the engine oil should decrease as the vehicle load increases (which is in agreement with field trial results). The percentage fuel saving from the axle and gearbox oils initially decreases with load and then stays more or less constant. This behaviour is due to the detailed way in which axle and gearbox efficiency varies with speed/load and lubricant type.

Due to the recent drive to reduce CO₂ emissions, the turbocharged direct injection spark ignition (turbo DISI) gasoline engine has become increasingly popular. In addition, future turbo DISI engines could incorporate a form of charge dilution (e.g., lean operation or external EGR) to further increase fuel efficiency. Thus, the conditions experienced by the fuel before and during combustion are and will continue to be different from those experienced in naturally aspirated SI engines. This work investigates the effects of fuel properties on a modern and prototype turbo DISI engine, with particular focus on the octane appetite: How relevant are RON and MON in predicting a fuel's anti-knock performance in these modern/future engines? It is found that fuels with high RON and low MON values perform the best, suggesting the current MON requirements in fuel specifications could actually be detrimental.

Addition of nitroalkanes to gasoline is shown to reduce the octane quality. The reduction in the Motor Octane Number (MON) is greater than the reduction in the Research Octane Number (RON). In other words addition of nitroalkanes causes an increase in octane sensitivity. The temperature of the compressed air/fuel mixture in the MON test is higher then in the RON test. Through chemical kinetic modelling, we are able to show how the temperature dependence of the reactions responsible for break-up of the nitroalkane molecule can lead to an increase in octane sensitivity. Results are presented from an Homogenous Charge Compression Ignition (HCCI) engine with a homogeneous charge in which the air intake temperature was varied. When the engine was operated on gasoline-like fuels containing nitroalkanes, it was observed that the combustion phasing was much more sensitive to the air intake temperature. This suggests a possible means of controlling combustion phasing for HCCI.

In this study, the influence of gasoline composition on exhaust emissions has been evaluated using three gasoline vehicles. Although the vehicles were obtained within Europe, each is representative of models to be found in Asian markets. Two of the vehicles were current Euro 4 certification, while the third was of Euro 2 certification equivalent to that available in specific Asian markets. Fuel effects studied included aromatics, olefins and benzene content. Other fuel properties were held constant within the normal constraints of blending when using realistic gasoline components. An orthogonal matrix of eight fuels was blended to evaluate these properties over the ranges: Aromatics (excluding benzene) 34% to 49%, olefins 18% to 25% and benzene 1% to 5%. All fuels were tested in all three cars driving the current legislative NEDC cycle, using a randomised block design with at least 3 repeats on each fuel/vehicle combination.

Lubricant samples were aged on a SI bench engine that was run using ten different gasoline fuels. For each gasoline tested, the oxidative stability of the lubricant and the extent of engine wear was assessed in terms of a number of different parameters. Surprisingly, it was found that fuels containing higher levels of olefin (whether C8 olefin, or a C5/C6 olefin blend, or a catalytically cracked refinery stream) performed directionally better than a reference gasoline with low levels of aromatics and olefins. Fuels with a higher final boiling point and higher aromatic content, appeared to be associated with enhanced levels of sludge formation than the reference gasoline, but did not give rise to enhanced engine wear.

The Coordinating European Council, CEC, develops performance tests for the motor, oil, petroleum, additive and allied industries. In recent years, CEC has moved away from using round robin programmes (RRP's) for monitoring the precision and severity of test methods in favour of regular referencing within a test monitoring system (TMS). In a TMS, a reference sample of known performance, determined by cross-laboratory testing, is tested at regular intervals at each laboratory. The results are plotted on control charts and determine whether the installation is and continues to be fit to evaluate products. Results from all laboratories are collated and combined to monitor the general health of the test. The TMS approach offers considerable benefits in terms of detecting test problems and improving test quality. However, the effort required in collating data for statistical analysis is much greater, and there are technical difficulties in determining precision from TMS data.