Search Results

A road test on semi-trailers is carried out, and accelerations of some characteristic points on the braking system,axles,and truck body is measured,also brake pressure and noise around the support frame is acquired.The measured data was analyzed to determine the causes of the brake noise, and the mechanism of the noise of the drum brake of semi-trailers during low-speed braking was investigated. The following conclusions are obtained: (1) Brake noise of the drum brake of the semi-trailer at low-frequency is generated from vibrations of the brake shoes, axle, and body, and the vibration frequency is close to 2nd natural frequency of the axle. (2) Brake noise is generated from stick-slip motion between the brake shoes and the brake drum, where the relative motion between the brake drum and the brake shoes is changed alternately with sliding and sticking, resulting in sudden changes in acceleration and shock vibration.

To reduce the heating energy consumption of electric vehicles in winter, a switching control strategy for multiple heating modes formed by three heat sources, including air, motor waste heat, and positive temperature coefficient (PTC) heaters, is designed. Firstly, an integrated thermal management system (ITMS) simulation model for the heat pump air conditioning system, battery thermal management system, and motor thermal management system is established based on the AMESim software. Secondly, the influence of ambient temperature and motor outlet coolant temperature on the heating performance of three cabin heating modes is studied. Specifically, the three cabin heating modes include the pure motor waste heat source heat pump mode, the pure air-source heat pump mode, and the dual heat source heat pump mode with waste heat source and air source. Based on the analysis results, the opening and closing strategies for the three cabin heating modes are discussed.

Battery Run-down under the Electric Vehicle Operation (BREVO) model is a model that links the driver’s travel pattern to physics-based battery degradation and powertrain energy consumption models. The model simulates the impacts of charging behavior, charging rate, driving patterns, and multiple energy management modules on battery capacity degradation. This study implements reinforcement learning (RL) to the simplified BREVO model to optimize drivers’ decisions on charging such as charging rate, charging time, and charging capacity needed. This is done by a reward function that considers both the driver’s daily travel demands and the minimization of battery degradation over a year. It shows that using appropriate charger type (No Charge, Level 1, Level 2, direct-current Fast Charge [DCFC], extreme Fast Charging [xFC]) with an appropriate charging time can reduce battery degradation and total charging cost at the end of the year while satisfying driver’s daily travel demand.

A set of enthalpy difference test equipment is set up to test flow and heat exchange performance of chillers. The empirical correlations for the convective heat transfer coefficients on the coolant side and the refrigerant side are obtained by fitting the test data, and a two-particle lumped parameter model of the chiller is established. Based on this, the heat exchange performance of the chiller under different operating conditions is given. The effects of herringbone corrugated plate parameters, including angle, pitch, and depth, on flow and heat exchange performance of chillers under different flow rates are further studied. Using the Wilson plot method in test design, the thermal resistance of convective heat transfer on each side is separated from the total thermal resistance to calculate the convective heat transfer coefficient.

A battery cooling system model of electric vehicle was established. The system model consists of a battery pack, a pump, a radiator, and a fan. A cooling plate was used to cool the battery pack, and the coolant flow rate in the cooling plate was controlled by the pump. The heat in the battery cooling system was released into the ambient air through the radiator. A finite element analysis model of the cooling plate was established to calculate the pressure drop of the cooling plate. A coupled dynamics model of the battery pack-radiator cooling system was established to simulate the temperature of the battery pack during charging and discharging. Tests were carried out to obtain the pressure drop of the cooling plate and the temperature of the battery pack under different working conditions. The simulation results and test results were compared and analyzed, and the accuracy of the models were verified.

Electric vehicle battery thermal management based on liquid cooling is the mainstream form of cooling for new energy vehicles. According to energy consumption, the system is divided into active cooling system and passive cooling system. The cooling of battery modules in these two cooling systems is carried out by liquid-cooled plate, which is connected in series in the cooling system. Therefore, the design of the liquid-cooled plate has a great impact on the effect of battery heat dissipation. In this paper, considering the advantages of existing liquid-cooled plates, the author proposed a series-parallel hybrid dc channel liquid-cooled plate structure, taking square lithium iron phosphate battery pack as the research object. Finally, the effects of different inlet flows and temperatures of the liquid-cooled plate on the thermal performance of the liquid-cooled plate were investigated by using single factor analysis.

Robust data association is a core problem of visual odometry, where image-to-image correspondences provide constraints for camera pose and map estimation. Current state-of-the-art visual semantic odometry uses local map points semantics, building semantic residuals associated with all classes to realize medium-term tracking of points. Considering the problem of inefficient semantic data associations and redundant semantic observation likelihood model in the visual semantic odometry, we propose a visual odometry, Local Semantic Odometry (LVSO), which is integrated with medium-term semantic constraints based on local nearest neighbor distance model.

As the power of electric vehicles (EVs), lithium-ion batteries (LIBs) are subjected to a variety of mechanical loads during electrochemical operation. Under this operating environment, lithium-ion batteries are at risk of internal short circuit, thermal runaway and even fire, threatening the safety of electric vehicles. The purpose of this paper is to investigate the mechanical behaviors and failure mechanisms of the battery separator to improve the safety of lithium-ion batteries under mechanical loads. In this study, uniaxial tensile, through-thickness compression and biaxial punch tests were performed to characterize two types of separators, dry-processed polypropylene (PP) separators and wet-processed ceramic-coated separators, and to analyze and compare their mechanical properties and failure modes. The comprehensive mechanical tests show that the failure modes of the different separator types are different, with the more anisotropic separator having more complex failure modes.

Because autonomous vehicles (AVs) equipped with active front steering have the features of time varying, uncertainties, high rate of fault, and high burden on the in-vehicle networks, this article studies the adaptive robust control problem for improving lateral stability in steer-by-wire (SBW) vehicles in the presence of abrupt nonlinear faults. First, an upper-level robust H∞ controller is designed to obtain the desired front-wheel steering angle for driving both the yaw rate and the sideslip angle to reach their correct values. Takagi-Sugeno (T-S) fuzzy modeling method, which has shown the extraordinary ability in coping with the issue of nonlinear, is applied to deal with the challenge of the changing longitudinal velocity. The output of the upper controller can be calculated by a parallel distributed compensation (PDC) scheme.

Because the power unit of electric vehicle has large torque, the rubber mount of electric vehicle is fully compressed under the condition of full throttle acceleration. When designing the mount of electric vehicle, the dynamic-to-static stiffness ratio of mount under the case should be as low as possible to improve the vibration isolation rate of the mount. In this paper, a method for calculating the high frequency dynamic characteristics of rubber isolators under different preloads is presented. Firstly, the dynamic characteristics of rubber specimens under various shear pre-strains were tested. The test results show that the dynamic stiffness of specimen decreases at first and then increases with the increase of shear strain. The viscoelastic parameters of rubber in frequency domain under different pre-strain were identified according to the experimental data. Secondly, a finite element modeling method was proposed.

The vehicle will produce certain shock and vibration during the braking process, which will affect the driving experience of the driver. Aiming at the problems of pitch vibration, longitudinal vibration and shock during the braking process, this paper proposes a planning and following control method for target longitudinal acceleration in post-braking phase, and designs control trigger strategies. Target longitudinal acceleration planning takes minimizing longitudinal shock as the design goal. The following control takes the brake pressure as the control object, and adopts the “feedforward +PID feedback” method to follow the target longitudinal acceleration. Besides, considering the safety of braking process, the trigger condition of control is designed which utilizes BP neural network method to judge whether the control has to be triggered. Based on Simulink software, the simulation model of straight-line braking is established.

For the improvement of the vehicle yaw stability, this paper studies the control problem of the active front steering (AFS) system with actuator input delay. A novel sliding mode predictive control method to handle actuator input delay is proposed for the AFS system. Firstly, considering the nonlinearities of the vehicle system, a linear parameter varying vehicle system model with two-level structure is proposed to capture the vehicle dynamic behaviors. Secondly, to deal with the issues of actuator input delay and system constraints, a novel sliding mode predictive control method is put forward. In the process of controller design, a sliding mode control algorithm is employed for the improvement of the robustness of the control system, and then a model predictive control algorithm is employed to deal with system constraints.

The thermal management system, which is used to improve driving safety and thermal comfort, is one of the most important systems in electric vehicles. In recent years, researchers have coupled the heat pump system and the battery cooling system to effectively improve the heating COP (Coefficient of Performance). Therefore an accurate dynamic model of thermal management system plays a key role in investigating system performance and optimal control strategies. In this paper, an electric vehicle thermal management system based on four-way valve heat pump system is designed. The moving boundary method is improved by considering the unsteady flow of the external fluid, and then a 13-order dynamic model of the thermal management system is established. Firstly, the control equations of evaporator, condenser and chiller are derived according to the principle of conservation, and then a dynamic model of thermal management system is established in Simulink.

The durability road test of a vehicle is an important test to verify the reliability of vehicle components. In order to carry out the durability bench test for drive shaft systems of all-terrain vehicles, a method for acquiring time domain signals of articulation angles of the CVJ, input torque, and rotational speeds of drive shaft systems is proposed. The acquired load spectrum of drive shaft systems is preprocessed including deleting small amplitudes, de-drifting, deburring, filtering, etc. Peaks and valleys are extracted from the preprocessed load spectrum. Based on the graphic method and the estimator stabilization method, the upper and lower thresholds of the time domain extrapolation of the load spectrum are determined, and then the peaks and valleys excesses that exceed the upper and lower thresholds are extracted. The generalized pareto distribution function is used to fit the distribution of peaks and valleys excesses.

The distributed parameter method is used to establish the dynamic simulation model of the electric vehicle thermal management system and various parts, and the finite difference method is used to solve the model. A thermal management system model with same structure is established by AMESIM, and the accuracy of the dynamic simulation model is verified by comparing the deviation of the calculation result between this dynamic simulation model and AMESIM. Based on the established model, the influence of expansion valve opening on the temperature of battery pack and the influence on the heating comfort of the cabin were studied. A control strategy for the rapid cooling of the battery pack was proposed. The results show that the model established by the distributed parameter method provides quite well agreement with commercial equivalent software and can well reflect the flow state of the refrigerant in different zones of the same component.

To solve the contradiction between model complexity and the warning accuracy of the algorithm of the vehicle rollover warning, a rollover state warning method based on the secondary predictive zero-moment point position for vehicles is proposed herein. Taking a sport utility vehicle(SUV) as the research object, a linear three-degrees-of-freedom vehicle rollover dynamics model is established. On the basis of the model, the lateral position of the zero-moment point and its primary and secondary rates of change are calculated. Then, the theoretical solution of time-to-rollover of the vehicles is deduced from the lateral position of the secondary predictive zero-moment point. When the rollover warning index, the lateral position of the zero-moment point, is greater than the set threshold, the active anti-rollover control system will be triggered. The active anti-rollover braking control system adopts a hierarchical control strategy.

This paper designs the important components and structure of the integrated electro-hydraulic brake system (I-EHB). Firstly, the simplified linear system is modeled, and the transfer function without considering the nonlinear disturbance such as system friction is derived, and the correctness of the linear system is preliminarily verified by AMESim. Then set up the I-EHB system test bench, and use the Stribeck friction model to identify the friction torque parameters in the static and kinetic friction stages of the system to obtain a more accurate friction model. Finally, based on the I-EHB system model of friction disturbance, a pressure-speed-current three-loop cascade PID controller is designed, and a feedforward controller based on the system model is added to form the control structure of “pressure feedforward compensation + pressure-speed-current closed-loop cascade PID”.

With the popularity of battery electric vehicles, the engine of the vehicle disappears, so the problem of road noise in cars is becoming more and more prominent. Road noise into the car can be divided into structure-borne noise and airborne noise, this paper only focuses on the airborne noise above 500Hz, completely ignoring the structure-borne noise. A transfer path analysis model with “Intermediate Response Points” is proposed to accurately represent the transfer path of each airborne noise through the setting of “Intermediate Points”. In the Vehicle Semi-Anechoic Room With 4×4 NVH Chassis Dyno, it is possible to create a working condition with only four tires running, so only the tire noise is considered in this paper. The frequency response function is tested in the Semi-Anechoic Chamber and the operating data is tested in the Vehicle Semi-Anechoic Room With 4×4 NVH Chassis Dyno.

Electric vehicle motors have the characteristics of fast torque response, large amplitude, and braking feedback torque. Therefore, the excitation of the electric vehicle powertrain has obvious transient impact characteristics, which put forward new requirements for the design of the mounting system. This article carried out the real vehicle test of rapid acceleration and rapid deceleration. A 12-degree-of-freedom nonlinear dynamic model of the electric vehicle mounting system is established. The model is used to calculate the vibration acceleration of the active side and the passive side of the mount, and compared with the test value to verify the correctness of the simulation model. The impact degree, the maximum pitch angle of the powertrain, and the longitudinal acceleration of the powertrain centroid are used as evaluation indicators to analyze the transient response of the electric vehicle mounting system under rapid acceleration and rapid deceleration conditions.

Two-layer engine front end accessory drive systems (TEFEADS) are adopted generally by commercial vehicles due to the characteristics of the accessory pulleys, which have large torque and moment of inertia. An overrunning alternator decoupler (OAD) is an advanced vibration isolator which can reduce the amplitude of torsional vibration of alternator rotor effectively by an one-way transmission and they are more and more widely used in vehicles. This paper established a model of a generic layout of a TEFEADS with an OAD. The coupling effect between the TEFEADS, the nonlinear characteristics of OAD, the torsional vibration of crankshaft and the creeping on the belt were taken into account. A nine pulleys model was provided as a study example, the dynamic responses, which are respectively under steady and accelerating conditions, of the system were calculated by the established method and compared with the bench experiment.