Search Results

Engine and aftertreatment solutions have been identified to meet the upcoming ultra-low NOX regulations on heavy duty vehicles in the United States and Europe. These standards will require changes to current conventional aftertreatment systems for dealing with low exhaust temperature scenarios while increasing the useful life of the engine and aftertreatment system. Previous studies have shown feasibility of meeting the US EPA and California Air Resource Board (CARB) requirements. This work includes a 15L diesel engine equipped with cylinder deactivation (CDA) and an aftertreatment system that was fully DAAAC aged to 800,000 miles. The aftertreatment system includes an e-heater (electric heater), light-off Selective Catalytic Reduction (LO-SCR) followed by a primary aftertreatment system containing a DPF and SCR.

In response to global climate change, there is a widespread push to reduce carbon emissions in the transportation sector. For the difficult to decarbonize heavy-duty (HD) vehicle sector, lower carbon intensity fuels can offer a low-cost, near-term solution for CO2 reduction. The use of natural gas can provide such an alternative for HD vehicles while the increasing availability of renewable natural gas affords the opportunity for much deeper reductions in net-CO2 emissions. With this in consideration, the US National Renewable Energy Laboratory launched the Natural Gas Vehicle Research and Development Project to stimulate advancements in technology and availability of natural gas vehicles. As part of this program, Southwest Research Institute developed a hybrid-electric medium-HD vehicle (class 6) to demonstrate a substantial CO2 reduction over the baseline diesel vehicle and ultra-low NOx emissions.

In this study, engine-out gaseous emissions are reviewed using the Fourier Transform Infrared (FTIR) spectroscopy measurement of methanol diesel dual fuel combustion experiments performed in a heavy-duty diesel engine. Comparison to the baseline diesel-only condition shows that methanol-diesel dual fuel combustion leads to higher regulated carbon monoxide (CO) emissions and unburned hydrocarbons (UHC). However, NOX emissions were reduced effectively with increasing methanol substitution rate (MSR). Under dual-fuel operation with methanol, emissions of nitrogen oxides (NOX), including nitric oxide (NO), nitrogen dioxide (NO2), and nitrous oxide (N2O), indicate the potential to reduce the burden of NOX on diesel after-treatment devices such as selective catalytic reduction (SCR).

The US EPA and the California Air Resources Board (CARB) require electric vehicle range to be determined according to the Society of Automotive Engineers (SAE) surface vehicle recommended practice J1634 - Battery Electric Vehicle Energy Consumption and Range Test Procedure. In the 2021 revision of the SAE J1634, the Short Multi-Cycle Test (SMCT) was introduced. The proposed testing protocol eases the chassis dynamometer test burden by performing a 2.1-hour drive cycle on the dynamometer, followed by discharging the remaining battery energy into a battery cycler to determine the Useable Battery Energy (UBE). Opting for a cycler-based discharge is financially advantageous due to the extended operating time required to fully deplete a 70-100kWh battery commonly found in Battery Electric Vehicles (BEVs).

Pouch cells are increasingly popular form factors for the construction of energy storage systems in electric vehicles of all classes. Knowledge of the stress generated by these higher capacity pouch cells is critical to properly design battery modules and packs for both normal and abnormal operation. Existing literature predominantly offers data on smaller pouch cells with capacities of less than 10 Ah, leaving a gap in our understanding of the behavior of these larger cells. This experimental study aimed to bridge this knowledge gap by measuring loads and stresses in constrained 65 Ah pouch cells under both cycling and abuse conditions. To capture the desired responses, a load cell was located within a robust fixture to measure cell stress in real time after the application of a preload of approximately 30 kilograms or 294 N, equivalent to a pressure of 0.063 bar, with a fixed displacement.

Vehicle-to-everything (V2X) communication, primarily designed for communication between vehicles and other entities for safety applications, is now being studied for its potential to improve vehicle energy efficiency. In previous work, a 20% reduction in energy consumption was demonstrated on a 2017 Prius Prime using V2X-enabled algorithms. A subsequent phase of the work is targeting an ambitious 30% reduction in energy consumption compared to a baseline. In this paper, we present the Eco-routing algorithm, which is key to achieving these savings. The algorithm identifies the most energy-efficient route between an Origin-Destination (O-D) pair by leveraging information accessible through commercially available Application Programming Interfaces (APIs). This algorithm is evaluated both virtually and experimentally through simulations and dynamometer tests, respectively, and is shown to reduce vehicle energy consumption by 10-15% compared to the baseline over real-world routes.

Methanol is one of the most promising fuels for the decarbonization of the off-road and transportation sectors. Although methanol is typically seen as an alternative fuel for spark ignition engines, mixing-controlled compression ignition (MCCI) combustion is typically preferred in most off-road and medium-and heavy-duty applications due to its high reliability, durability and high-efficiency. In this paper, the potential of using ignition enhancers to enable methanol MCCI combustion was investigated. Methanol was blended with 2-ethylhexyl nitrate (EHN) and experiments were performed in a single-cylinder production-like diesel research engine, which has a displacement volume of 0.83 L and compression ratio of 16:1. The effect of EHN has been evaluated with three different levels (3%vol, 5%vol, and 7%vol) under low- and part-load conditions. The injection timing has been swept to find the stable injection window for each EHN level and load.

Biodiesel (i.e., mono-alkyl esters of long chain fatty acids derived from vegetable oils and animal fats) is a renewable diesel fuel providing life-cycle greenhouse gas emission reductions relative to petroleum-derived diesel. With the expectation that there would be widespread use of biodiesel as a substitute for ultra-low sulfur diesel (ULSD), there have been many studies looking into the effects of biodiesel on engine and aftertreatment, particularly its compatibility to the current aftertreatment technologies. The objective of this study was to generate experimental data to measure the effectiveness of a current technology diesel oxidation catalysts (DOC) to oxidize soy-based biodiesel at various blend levels with ULSD. Biodiesel blends from 0 to 100% were evaluated on an engine using a conventional DOC.

Engine knock is one of the limiting factors in determining the compression ratio and engine efficiency for spark ignited engines. Using the Southwest Research Institute Knock-CoV test method, it was previously shown that the knock limited load versus combustion phasing (CA50) has a constant slope. All of the knock mitigation strategies tested provided a shift to these knock limited loads but also increased the slope. That is, for the same CA50 retard the knock limited load could be increased more. Our hypothesis was that due to fuel sensitivity, or the difference between the RON and MON, the reactions that lead to knock will behave differently as the pressure-temperature history changes with engine speeds and loads. The fuel affects on the knock and CoV limits were studied by testing fuels with various sensitivities including methanol, E85 (85% ethanol) and Iso-octane.

Ethanol blending is one method that can be used to reduce knock in spark ignition engines by decreasing the autoignition reactivity of the fuel and modifying its laminar flame speed. In this paper, the effects of ethanol blending on knock propensity and flame speed of petroleum and low-carbon gasoline fuels is analyzed. To do so, surrogate fuels were formulated for methanol-to-gasoline (MTG) and ethanol-to-gasoline (ETG) based on the fuels’ composition, octane number, and select physical properties; and 0-D and 1-D chemical kinetics simulations were performed to investigate reactivity and laminar flame speed, respectively. Results of MTG and ETG were compared against those of PACE-20, a well-characterized surrogate for regular E10 gasoline. Similarly to PACE-20, blending MTG and ETG with ethanol increases the fuel’s research octane number (RON) and sensitivity.

Low-temperature gasoline combustion (LTGC) engines can provide high efficiencies with very low NOx and soot emissions, but rapid control of the combustion timing remains a challenge. Partial Fuel Stratification (PFS) was demonstrated to be an effective approach to control combustion in LTGC engines. PFS is produced by a double-direct injection (DI) strategy with most of the fuel injected early in the cycle and the remainder of the fuel supplied by a second injection at a variable time during the compression stroke to vary the amount of stratification. Adjusting the stratification changes the combustion phasing, and this can be done on cycle-to-cycle basis by adjusting the injection timing. In this paper, the ability of PFS to control the combustion during wide engine load sweeps is assessed for regular gasoline and gasoline doped with 2-ethylhexyl nitrate (EHN). For PFS, the load control range is limited by combustion instability and poor combustion efficiency at low loads.

Methanol emerges as a compelling renewable fuel for decarbonizing engine applications due to a mature industry with high production capacity, existing distribution infrastructure, low carbon intensity and favorable cost. Methanol’s high flame speed and high autoignition resistance render it particularly well-suited for spark-ignition (SI) engines. Previous research showed a distinct phenomenon, known deflagration-based knock in methanol combustion, whereby knocking combustion was observed albeit without end-gas autoignition. This work studies the implications of deflagration-based knock on noise emissions by investigating the knock intensity and combustion noise at knock-limited operation of methanol in a single-cylinder direct-injection SI engine operated at both stoichiometric and lean (λ = 2.0) conditions. Results are compared against observations from a premium-grade gasoline.

Since the early 1990’s, commercial vehicles have suffered from repeated vulnerability exploitations that resulted in a need for improved automotive cybersecurity. This paper outlines the strategies and challenges of implementing an automotive Zero Trust Architecture (ZTA) to secure intra-vehicle networks. Zero Trust (ZT) originated as an Information Technology (IT) principle of “never trust, always verify”; it is the concept that a network must never assume assets can be trusted regardless of their ownership or network location. This research focused on drastically improving security of the cyber-physical vehicle network, with minimal performance impact measured as timing, bandwidth, and processing power. The automotive ZTA was tested using a software-in-the-loop vehicle simulation paired with resource constrained hardware that closely emulated a production vehicle network.

Multiple areas in the U.S. continue to struggle with achieving National Ambient Air Quality Standards for ozone. These continued issues highlight the need for further reductions in NOX emission standards in multiple industry sectors, with heavy-duty on-highway engines being one of the most important areas to be addressed. Starting in 2014, CARB initiated a series of technical demonstration programs aimed at examining the feasibility of achieving up to a 90% reduction in tailpipe NOX, while at the same time maintaining a path towards GHG reductions that will be required as part of the Heavy-Duty Phase 2 GHG program. These programs culminated in the Stage 3 Low NOX program, which demonstrated low NOX emissions while maintaining GHG emissions at levels comparable to the baseline engine.

Off-road diesel engines remain one of the most significant contributors to the overall oxides of nitrogen (NOX) inventory and the California Air Resources Board (CARB) has indicated that reductions of up to 90% from current standards may be necessary to achieve its air quality goals. In recognition of this, CARB has funded a program aimed at demonstrating emission control technologies for off-road engines. This program builds on previous efforts to demonstrate Low NOX technologies for on-road engines. The objective was to demonstrate technologies to reduce tailpipe NOX and particulate matter (PM) emissions by 90 and 75%, respectively, from the current Tier 4 Final standards. In addition, the emission reductions were to be achieved while also demonstrating a 5 to 8.6% carbon dioxide (CO2) reduction and remaining Greenhouse Gas (GHG) neutral with respect to nitrous oxide (N2O) and methane (CH4).

Surrogate fuels that reproduce the characteristics of full-boiling range fuels are key tools to enable numerical simulations of fuel-related processes and ensure reproducibility of experiments by eliminating batch-to-batch variability. Within the PACE initiative, a surrogate fuel for regular-grade E10 (10%vol ethanol) gasoline representative of a U.S. market gasoline, termed PACE-20, was developed and adopted as baseline fuel for the consortium. Although extensive testing demonstrated that PACE-20 replicates the properties and combustion behavior of the full-boiling range gasoline, several concerns arose regarding the purity level required for the species that compose PACE-20. This is particularly important for cyclo-pentane, since commercial-grade cyclo-pentane typically shows 60%–85% purity. In the present work, the effects of the purity level of cyclo-pentane on the properties and combustion characteristics of PACE-20 were studied.

1Increasing adoption of downsized, boosted, spark-ignition engines has improved vehicle fuel economy, and continued improvement is desirable to reduce carbon emissions in the near-term. However, this strategy is limited by damaging preignition events which can cause hardware failure. Research to date has shed light on various contributing factors related to fuel and lubricant properties as well as calibration strategies, but the causal factors behind an individual preignition cycle remain elusive. If actionable precursors could be identified, mitigation through active control strategies would be possible. This paper uses artificial neural networks to search for identifiable precursors in the cylinder pressure data from a large real-world data set containing many preignition cycles. It is found that while follow-up preignition cycles in clusters can be readily predicted, the initial preignition cycle is not predictable based on features of the cylinder pressure.

Conventional diesel combustion (CDC) is known to provide high efficiency and reliable engine performance, but often associated with high particulate matter (PM) and nitrogen oxides (NOX) emissions. Combustion of fossil diesel fuel also produces carbon dioxide (CO2), which acts as a harmful greenhouse gas (GHG). Renewable and low-carbon fuels such as renewable diesel (RD) and methanol can play an important role in reducing harmful criteria and CO2 emissions into the atmosphere. This paper details an experimental study using a single-cylinder research engine operated under dual-fuel combustion using methanol and RD. Various engine operating strategies were used to achieve diesel-like fuel efficiency. Measurements of engine-out emissions and in-cylinder pressure were taken at test conditions including low-load and high-load operating points.

For 2D surface temperature monitoring applications, a variant of Electrical Impedance Tomography (EIT) was evaluated computationally in this study. Literature examples of poor sensor performance in the center of the 2D domains away from the side electrodes motivated these efforts which seek to overcome some of the previously noted shortcomings. In particular, the use of ‘sensing skins’ with novel tailored baseline conductivities was examined using the EIDORS package for EIT. It was found that the best approach for detecting a temperature hot spot depends on several factors such as the current injection (stimulation) patterns, the measurement patterns, and the reconstruction algorithms. For well-performing combinations of these factors, customized baseline conductivities were assessed and compared to the baseline uniform conductivity.

Low carbon emissions policies for the transportation sector have recently driven more interest in using low net-carbon fuels, including biodiesel. An internal combustion engine (ICE) can operate effectively using biodiesel while achieving lower engine-out emissions, such as soot, mostly thanks to oxygenate content in biodiesel. This study selected a heavy-duty (HD) single-cylinder engine (SCE) platform to test biodiesel fuel blends with 20% and 100% biodiesel content by volume, referred to as B20, and B100. Test conditions include a parametric study of exhaust gas recirculating (EGR), and the start of injection (SOI) performed at low and high engine load operating points. In-cylinder pressure and engine-out emissions (NOX and soot) measurements were collected to compare diesel and biodiesel fuels.