Search Results

It has been widely known that thermal and fuel stratifications of in-cylinder mixture are effective to reduce in-cylinder pressure rise rate during high load HCCI operations. In order to optimize a combustion chamber design and combustion control strategy for HCCI engines with wide operational range, it is important to know quantitatively the influence of the temperature and fuel concentration distributions on ignition and heat release characteristics. At the same time, it is important to know the influence of in-cylinder flow and turbulence on the temperature and fuel concentration distributions. In this study, a numerical simulation of HCCI combustion were conducted to investigate the effects of the in-cylinder flow and turbulence, and the distributions of temperature on ignition and combustion characteristics in HCCI combustion.

A wall-resolving Large Eddy Simulation (LES) has been performed by using up to 40 billion grids with a minimum grid resolution of 0.1 mm for predicting the exterior hydrodynamic pressure fluctuations in the turbulent boundary layers of a test car with simplified geometry. At several sampling points on the car surface, which included a point on the side window, the door panel, and the front fender panel, the computed hydrodynamic pressure fluctuations were compared with those measured by microphones installed on the surface of the car in a wind tunnel, and effects of the grid resolution on the accuracy of the predicted frequency spectra were discussed. The power spectra of the pressure fluctuations computed with 5 billion grid LES agreed reasonably well with those measured in the wind tunnel up to around 2 kHz although they had some discrepancy with the measured ones in the low and middle frequencies.

Unresolved issues of Homogeneous Charge Compression Ignition (HCCI) combustion include an extremely rapid pressure rise on the high load side and resultant knocking. Studies conducted to date have examined ways of expanding the region of stable HCCI combustion on the high load side such as by applying supercharging or recirculating exhaust gas (EGR). However, the effect of applying EGR gas to supercharged HCCI combustion and the mechanisms involved are not fully understood. In this study, the effect of EGR gas components on HCCI combustion was investigated by conducting experiments in which external EGR gas was applied to supercharged HCCI combustion and also experiments in which nitrogen (N2) and carbon dioxide (CO2) were individually injected into the intake air pipe to simulate EGR gas components. In addition, HCCI combustion reactions were analyzed by conducting chemical kinetic simulations under the same conditions as those of the experiments.

The objective of this paper is to investigate the potential of lean burn combustion to improve the thermal efficiency of spark ignition engine. Experiments used a single cylinder gasoline spark ignition engine fueled with primary reference fuel of octane number 90, running at 4000 revolution per minute and at wide open throttle. Experiments were conducted at constant fueling rate and in order to lean the mixture, more air is introduced by boosted pressure from stoichiometric mixture to lean limit while maintaining the high output engine torque as possible. Experimental results show that the highest thermal efficiency is obtained at excess air ratio of 1.3 combined with absolute boosted pressure of 117 kPa. Three dimensional computational fluid dynamic simulation with detailed chemical reactions was conducted and compared with results obtained from experiments as based points.

Various sensors including throttle position sensors (TPS), manifold pressure sensors (MPS), crank angle sensors, engine temperature sensors, and oxygen sensors are mounted in electronically controlled fuel injection (FI) systems to accurately regulate the air-fuel ratio according to the operating state and operating environment. Among these vehicle-mounted sensors, TPS has functions for detecting a fully-closed throttle and estimating intake air volume by the amount of throttle opening. Currently, we have conducted a study on transferring TPS functions into the MPS (manifold pressure sensor) in order to eliminate the TPS. Here we report on detecting a fully-closed throttle for achieving fuel cut control (FCC) and idle speed control (ISC) in fuel injection systems. We contrived a means for fully-closed throttle detection during ISC and controlling changes in the bypass opening during FCC in order to accurately judge each fully-closed throttle state via the manifold pressure.

Cost reduction is an important development goal for small motorcycles (1). As a way to reduce costs, we have developed an electronically controlled fuel injection (hereafter FI) system without a throttle position sensor (hereafter TPS). Ordinarily, the high throttle range is controlled and computed by TPS, and the low throttle range by manifold pressure sensor (hereafter MPS). The intake airflow is estimated with consistent high precision regardless of the engine load, and the basic fuel injection is executed accordingly. Also, transient correction monitors the size of TPS changes, to inject fuel immediately when a TPS change equal to or greater than a threshold value is detected. In our development, we replaced these functions with control by MPS. For calculation of basic fuel injection quantity by MPS, we carried on the conventional method. However, MPS transient correction control had some aspects with poor tracking.

Currently, the improvement of fuel economy is the most important issue in automobile engine development. To improve fuel economy via greater thermal efficiency, the enhancement of the compression ratio and the reduction of thermal losses because of cooling have been widely investigated. These efforts to improve thermal efficiency increase the thermal load on pistons. Ensuring the reliability of the pistons and the antiknocking capacity of engines require a better understanding of piston temperature distributions through accurate measurements under various engine operating conditions. Thus, direct and indirect measurement methods have been developed to estimate the actual piston temperature. Direct methods, such as linkage-type measurements, are not typically applicable under higher engine speeds because of the poor durability of linkages.

A great deal of interest is focused on Homogeneous Charge Compression Ignition (HCCI) combustion today as a combustion system enabling internal combustion engines to attain higher efficiency and cleaner exhaust emissions. Because the air-fuel mixture is compression-ignited in an HCCI engine, control of the ignition timing is a key issue. Additionally, because the mixture ignites simultaneously at multiple locations in the combustion chamber, it is necessary to control the resultant rapid combustion, especially in the high-load region. Supercharging can be cited as one approach that is effective in facilitating high-load operation of HCCI engines. Supercharging increases the intake air quantity to increase the heat capacity of the working gas, thereby lowering the combustion temperature for injection of the same quantity of fuel. In this study, experiments were conducted to investigate the effects of supercharging on combustion characteristics in an HCCI engine.

The purpose of this study was to measure the distribution and volume of liquid film adhering to the walls after the injection of fuel by an injector of a port-injection engine using the laser induced fluorescence (LIF) method while changing the fuel pressure and the angle of injection, and to consider how adhesion can be reduced in order to decrease the exhaust emission of gasoline engine. Using a high-speed camera, we filmed the adhesion and evaporation of liquid film in time series. Perylene, used here as a fluorescence dye, was blended with a fuel comprising toluene and n-heptane, and the mixture was injected onto a solid surface using a port-injection injector. UVLED with a maximum output wavelength of 375 nm was used as the exciting light. To more accurately measure the volume of fuel adhesion, it was necessary to correct the unevenness of the light source.

Traditionally, a Boundary Element Method (BEM) is often used for a radiation noise analysis. In recent years, to define an infinite region, a Finite Element Method (FEM) that can use an infinite boundary condition has been developed. However, studies on the radiation noise analysis by the FEM are few. Recently a number of an electric scooter has been increased. One of development issues is a radiation noise by a vibration of a wall surface of a swing-arm. In this paper, the vibration of the wall surface of the swing-arm is calculated, and a sound pressure level (SPL) of the radiation noise is calculated using a result of the frequency response analysis. And compare results of an experimental and an analytical sound pressure, its results were matched to within 5% error. Furthermore we used the method of this paper, proposed the model to reduce the radiation noise 10dB. Then we compare with the FEM and the BEM to verify the computation time and the mesh size.

To measure the stresses acting on the crankshaft of an engine, signals must be taken out from the rapidly spinning shaft. This paper discusses the measurement of stress signals from the crankshaft using a slip ring, which is the conventional method. By developing a special fixture that allowed us to measure rotations up to 14,000 rpm and using the four-gauge method, we succeeded in accurately measuring stress waves. We confirmed that, during the motoring operation, stresses due to the secondary component of the inertia forces of the reciprocating parts are dominant and that, during the firing operation, deformation occurs at various frequency bands. As the engine speed increased, the stress amplitude increased and reached a maximum around the highest engine speed. The results of a static analysis predicted values close to actual measurements.

Anodizing is applied to improve the durability and the corrosion resistance of aluminum alloy parts of engines and car bodies. Generally, anodic oxide film is formed using direct current anodizing (DCA). However, in the case of anodizing high silicon aluminum alloy cast parts, it is difficult to derive uniform film thickness distribution. Furthermore, it takes a long treatment time which causes low productivity. In this study, the authors have developed an anodizing method by using high-frequency switching anodizing (HSA) to solve these problems. The growth process of anodic oxide film is susceptible to the metallographic structure. Thus, the typical DCA application to the high silicon aluminum alloy produces a non-uniform film thickness, while HSA has the potential to form uniform film without being affected by metallographic structure. Moreover, the current density of HSA is higher than that of DCA which reduces treatment time to 1/5 as the film formation enhances.

Lead-added free-cutting steel has been used by many parts which need high machinability because lead improves chip friability and drill life. However, the demand of lead reduction increases in recent years, because of environmental impact substance reduction. Therefore, we developed lead-free crankshaft for motorcycle. Until now, crankshaft for motorcycle has been manufactured with lead-added free-cutting steel by a following process; Hot-Forging - Quenching and Tempering (QT) - Prior Machining - Nitrocarburizing - Finishing process because of strength and machinability. When we tried to change steel to lead-free, we examined to change to sulfur-added free-cutting steel. However, chip friability of sulfur-added free-cutting steel is inferior to lead one. Thus, we concerned about increase in machining expense. Then, heat-treatment after forging was examined to change from QT to normalizing for reducing the heat-treatment expense.

We have developed a small-displacement gasoline direct-injection engine (1.3L). Gasoline direct-injection engines rely on ultra-lean stratified combustion to deliver significantly better fuel economy, and are already used in many practical applications. When gasoline direct-injection is applied to a small-displacement engine, however, the amount of wall wetting of fuel on the piston surface will increase because the traveled length of the fuel spray is short. This may result in problems such as smoke production, high emissions of unburned HC, and poor combustion efficiency.

In recent years, one of the most important issues in the automotive industry is the improvement of fuel economy started from the environmental problem. Making cars lighter and reducing the coefficient of friction are two ways to improve fuel economy. Reducing the weight of a cylinder, an engine component, is a typical example. The traditional, mainstream method to reduce cylinder weight has been to convert cast iron cylinder blocks into aluminum cylinder blocks by using cast iron sleeves. To further make engines lighter and more compact, however, it is desirable that cast iron sleeves be abolished, or, in other words, making cylinder blocks sleeveless. A typical technology to make cylinder blocks sleeveless is applying anti- wear coating on a bore wall. Electroplating is currently the mainstream method used for this technology. It must be noted, however, electroplating is used primarily for low-pressure cast cylinders.

We have developed an electronically controlled four-speed automatic transmission with a "D-range neutral control system" for vehicles of small piston displacements (0.66 to 1.0 liter). When the vehicle is stationary with the engine idling, the system reduces the pressure being supplied to the clutch, thereby creating a neutral clutch condition. This helps reduces fuel consumption of the stationary vehicle without intervention of the driver. The non-intervention, however, can cause discomfort for the driver when the system is engaged and disengaged as the vehicle condition (i.e., engine revolution speed, vibration or noise transmitted to the vehicle) may change noticeably. Such a cause of discomfort that surfaced during the system development stage was thoroughly investigated and successfully eliminated by improving the method of control.

The purpose of this study was to find compatible specifications both of emission reduction and high power output with good throttle response for a sports utility motorcycle. In the emission reduction challenge, we examined equipping the exhaust system with a catalytic converter to achieve sufficient emission reduction. The catalytic converter, however, caused a temperature rise in the exhaust system, which caused a pressure propagation change. Additional muffler design optimization effectively maintained high performance and acceleration. The exhaust valve device was also optimized for emission reduction and high power output over a wide engine speed range. The optimized control of the exhaust valve was beneficial to preventing short-circuit of fresh mixture gas and early activation of the catalyst. Such comprehensive specifications could satisfy the performance and driveability characteristics required for sports utility motorcycles.

Reduction of flow resistance in an intake system is essential for increasing the output of a four-stroke engine. Evaluation method regardless engine displacement or number of valves or cylinder must be required in intake system design. This study proposes intake loss coefficient as total evaluation method from flow in an intake port to charging flow into a cylinder. A three-dimensional, general-purpose Computational Fluid Dynamics (CFD) code was used to calculate an intake loss coefficient. A correlation was confirmed between an intake loss coefficient and the engine power output. Intake loss coefficients and the CFD technique may be used for efficient optimization of the shape of an intake system.

The purpose of this study was to detect a misfiring cycle in terms of the transfer-passage and the exhaust-pipe flow rate by experimental measurements. Simultaneous measurements of flow rates and in-cylinder pressure were carried out. The flow rate data were grouped into the different combustion classes by the in-cylinder pressure. A large flow rate of exhaust blow-down and a large reverse flow rate were observed in the cycle before misfiring, compared with in the cycle before firing. It showed that high concentration of the residual burnt gas in the cylinder was the main source of misfiring, this feature was also demonstrated by the complementary measurement of CO and CO2 concentrations.

The purpose of this study is to show cycle-to-cycle combustion variation in transient conditions of quick throttle opening and to control the combustion fluctuation improve acceleration in a two-stroke motorcycle engine. Two phases of engine operation were focused on: the low-load condition before quick throttle opening, and the transient condition after quick throttle opening. The time-series variation of the heat release rate based on the in-cylinder pressure, the engine-speed and the exhaust pressure variation were measured simultaneously, in an engine with a new multiple-timing-ignition-system, and in an engine with a modified exhaust port. Stable ignition performance and fast burning velocity were the keys to attaining smooth acceleration.