Search Results

The backward flow of the hot burned gas surrounding a diesel flame was found to be one of the factors dominating the set-off length (also called the lift-off length), that is, the distance from a nozzle exit into which a diffusion flame cannot intrude. In the combustion chamber of an actual diesel engine, the entrainment of the surrounding gas into a spray jet from a multi-hole nozzle is restricted by the walls and adjacent spray jets, which induces the backward flow of the surrounding gas. A new momentum theory to calculate the backward flow velocity was established by extending Wakuri's momentum theory. Shadowgraph imaging in an optical engine successfully visualized the backward flow of the hot burned gas.

The hole diameter of injection nozzles in diesel engines has become smaller and the nozzle coking could potentially cause injection characteristics and emissions to deteriorate. In this research, engine tests with zinc-added fuels, deposit analyses, laboratory tests and numerical calculations were carried out to clarify the deposit formation mechanisms. In the initial phase of deposit formation, lower zinc carboxylate formed close to the nozzle hole outlet by reactions between zinc in the fuel and lower carboxylic acid in the combustion gas. In the subsequent growth phase, the main component changed to zinc carbonate close to nozzle hole inlet by reactions with CO₂ in the combustion gas. Metal components and combustion gases are essential elements in the composition of these deposits. One way of removing these deposits is to utilize cavitations inside the nozzle holes.

In this paper, we will introduce a stereo vision system developed as a sensor for a vehicle's front monitor. This system consists of three parts; namely, a stereo camera that collects video images of the forward view of the vehicle, a stereo ECU that processes its output image, and a near-infrared floodlight for illuminating the front at night. We were able to develop an obstacle detection function for the Pre-Crash Safety System and also a traffic lane detection function for a Lane-Keeping Assist System. Especially in regard to the obstacle detection function, we were able to achieve real-time processing of the disparity image calculations that had formerly required long processing times by using two types of recently developed LSIs.

The performances of some vehicle control systems are influenced by changes in the weight of the vehicle. In these systems, it is important to be able to estimate the weight without the need for special sensors. When we use physical models to do this, we have to provide estimates for two or more unknown parameters. In addition, since such a method is influenced by disturbances in the measured signals, it is difficult to maintain an acceptable level of accuracy. So, after analyzing the physical phenomena, we developed a new method that eliminates the influence of the disturbances from the measured signals and constructed an estimation system that has a minimum number of unknown parameters that was capable of providing a more accurate estimate of a vehicle weight. This method was applied to the braking force control of an automatic transmission and its efficacy was verified.

We have developed a high capacity electromagnetic clutch by means of Si-containing diamond-like carbon (DLC-Si) coating. The durability of the new clutch is enhanced up to 8 times higher than that of the conventional one. Such a superior performance is due to several tribological properties of the DLC-Si film and micro morphology on the clutch surface. In particular, the DLC-Si plays a significant role in maintaining the groove shape of the clutch and giving sufficient friction in fluid, which is required for a drivetrain device. Besides, our deposition process (using direct current plasma-assisted chemical vapor deposition) has afforded homogeneous DLC-Si-coated clutches in large quantities. These techniques have enabled us to reduce the number of clutch discs per coupling and achieve a more compact and higher capacity AWD coupling at a lower cost.

A series calculation methodology from the injector nozzle internal flow to the in-cylinder fuel spray and mixture formation in a diesel engine was developed. The present method was applied to a valve covered orifice (VCO) nozzle with the recent common rail injector system. The nozzle internal flow calculation using an Eulerian three-fluid model and a cavitation model was performed. The needle valve movement during the injection period was taken into account in this calculation. Inside the nozzle hole, cavitation appears at the nozzle hole inlet edge, and the cavitation region separates into two regions due to a secondary flow in the cross section, and it is distributed to the nozzle exit. Unsteady change of the secondary flow caused by needle movement affects the cavitation distribution in the nozzle hole, and the spread angle of the velocity vector at the nozzle exit.

In order to increase the transfer efficiency in a metal V-belt type CVT (Continuously Variable Transmission), it is effective to lower belt clamping force from a current setting value. However, setting the clamping force too low will cause a macro slip (large belt slip). Thus, in order to set the clamping force to the proper level, the friction characteristics between the belt and the pulley (belt friction characteristics) must be understood in detail, and the macro slip threshold must be defined. In this paper, we shall propose a friction expression model for a metal V-belt type CVT and use this model to explain the speed reducing ratio dependence and speed dependence of the maximum friction coefficient (μmax). We shall also define the macro slip threshold in torque fluctuation environment.

We have proposed First Order Analysis (FOA) as a method, which the engineering designers themselves can use easily in an initial design stage. In this paper, we focus on the crashworthiness, and present the method to predict the collapse behavior of the frame member. This method is divided into two parts. Those are (1) collapse analysis under loading conditions of combined axial force and bending moment to the cantilever, and (2) collapse analysis of structural member considering the previously obtained moment - rotation angle relationship using the beam element. In comparison with the results according to the detailed Finite Element Analysis (FEA) model, effectiveness and validity of this method are presented.

The stratification feature of DI gasoline combustion was studied by using a constant volume combustion vessel. An index of stratification degree, defined as volumetric burning velocity, has been proposed based on the thermodynamic analysis of the indicated pressure data. The burning feature analysis using this stratification degree and the fuel vapor concentration measurement using He-Ne laser ray absorption method were carried out for the swirl nozzle spray with 90° cone angle and the slit nozzle spray with 60° fan angle. Ambient pressure and ambient temperature were changed from atmospheric condition to 0.5∼0.6 MPa and 465 K, respectively. Air Swirl with swirl ratio of 0∼1.0 were added for the 90° swirl nozzle spray. Single component fuels with different volatility and self-ignitability from each other were used besides gasoline fuel. The major findings are as follows. High ambient temperature improves stratification degree due to the enhanced fuel vaporization and vapor diffusion.

IGBT modules used in electric and hybrid vehicles are assembled by connecting approximately 500 thick Al wires ( ϕ 400 μ m), requiring the largest scale wire bonding of any automobile part. It is accepted that the probability of cracks occurring within the IGBT chip due to damage during wire bonding is about 1 in 1,000,000. Toyota has been conducting research to clarify the cause and generation mechanism of this problem. Other companies who have also conducted investigations have reported that the cause of the problem is Si nodules resulting from Si components within the Al electrode of the chip. However, characteristics of the generation mechanism, such as the influence of surface convexity of the chip and the path by which stress sufficient to generate cracks is exerted, have not been clearly explained. In this article, the generation mechanism is examined through detailed observations of damage within the chip and analysis of stress using simulations.

In direct-injection (DI) gasoline engines, spray characteristics greatly affect engine combustion. For the rapid development of new gasoline direct-injectors, it is necessary to predict the spray characteristics accurately by numerical analysis based on the injector nozzle geometry. In this study, two-phase flow inside slit nozzle injectors is calculated using the volume of fluid method in a three-dimensional CFD. The calculation results are directly applied to the boundary conditions of spray calculations, of which the submodels are recently developed to predict spray formation process in direct injection gasoline engines. The calculation results are compared with the experiments. Good agreements are obtained for typical spray characteristics such as spray shape, penetration and Sauter mean diameter at both low and high ambient pressures. Two slit nozzle injectors of which the slit thickness is different are compared.

Transmission error is the main cause of gear noise in automobile transmissions, and recently can be estimated by numerical analysis [1]. First, in this report, we establish the accurate numerical analysis of transmission error by using FE analysis and Hertz's contact analysis of gear tooth stiffness. Secondly, on the basis of the established numerical analysis, we develop a new tooth flank form to reduce transmission error. The new tooth flank form aims to ensure the coincidence of meshing stiffness at all meshing positions. Finally, a validation test using an experimental prototype is performed, and we confirm that the estimated effect by the new tooth flank form has been obtained.

A new stratified charge combustion system has been developed for direct injection gasoline engines. The special feature of this system is employment of a thin fan-shaped fuel spray formed by a slit nozzle. The stratified mixture is produced by the combination of this fan-spray and a shell-shaped piston cavity. Both under-mixing and over-mixing of fuel in the stratified mixture is reduced by this system. This combustion system does not require distinct charge motion such as tumble or swirl, which enables intake port geometry to be simplified to improve full load performance. The effects of the new system on engine performance at part load are improved fuel consumption and reduced smoke, CO and HC emissions, obviously at medium load and medium engine speed. HC emissions at light load are also improved even with high EGR conditions.

Our concern was with the phenomenon of the fuel flow rate change in the injector due to deposit formation in the direct injection gasoline engine. The fundamental factors in the deposit formation on the nozzle were investigated, and engine dynamometer tests were performed. It was clarified that the residual fuel in the nozzle hole should be kept in a liquid state so that deposit precursors could be washed away by fuel injections. As a consequence, the nozzle temperature had to be below the 90 vol. % distillation temperature of the fuel, which was the most important index to suppress the deposit formation.

It is important to more clearly identify the relationship among the ramping-up motion, straightening of the whole spine, and cervical vertebrae motion in order to clarify minor neck injury mechanism. The aim of the current study is to verify the influence of the change of the spine configuration on human cervical vertebral motion and on head/neck/torso kinematics under low speed rear-end impacts. Seven healthy human volunteers participated in the experiment under the supervision of an ethics committee. Each subject sat on a seat mounted on a sled that glided backward on rails and simulated actual car impact acceleration. Impact speeds (4, 6, and 8 km/h), and seat stiffness (rigid and soft) without headrest were selected. During the experiment, the change of the spine configuration (measured by a newly developed spine deformation sensor with 33 paired set strain gauges and placed on the skin) and the interface load-pressure distribution was recorded.

A study was conducted to reduce unburned oil fractions in diesel particulate matter (PM) by improving oil consumption. A method utilizing radioisotope 14C was developed to measure the unburned oil fractions separately for the four paths by which oil is consumed: valve stem seals, piston rings, PCV system, turbocharger. The conversion ratio of oil consumption to PM was calculated by comparing the unburned oil emission rates with oil consumption rates, which were obtained by the use of the 35S tracer method. The result in an experimental diesel engine shows the highest conversion ratio for the oil leaking through the valve stem seals. The modifications to the engine were thereby focused on reducing the leakage of the stem seals. This stem seal modification, along with piston ring improvements, reduced oil consumption, resulting in the unburned oil fractions in PM being effectively reduced.

A new experimental apparatus to visualize and measure the flow in the stator of a torque converter is proposed. A one-sided coaxial shaft constructed of an input shaft and an output shaft provides an open space inside the stator shaft for measurement. Through the window on the stator shaft, the flow in the stator can be directly observed. We also improved the laser sheet lighting method into the blade passage by using a mirror inside the blade. By visualizing the flow with the laser sheet lighting method, we found that the flow around the leading edge has different separation regions along the blade span. Furthermore, by using a laser doppler velocimeter, velocity vectors and turbulence intensities were measured in three stator blades of different thicknesses with the same camber line. The thickness of the stator blades affects the flow patterns.

Three-dimensional numerical analysis of fuel liquid and mixture behavior in a port-injection gasoline engine is assessed by comparing calculations with measurements. The fuel mass distributed in the intake port and cylinder is measured using an engine with hydraulic valve and gas sampling system. The experimental results show that about half of the fuel mass per injection enters the cylinder, and the rest stays in the port. The difference of the mass fraction of injected fuel directly entering the cylinder is small between the cases of single pulse injection and serial injection. Therefore, three-dimensional calculation presupposing single pulse injection has difficulty in predicting the in-cylinder mixture formation process, although it can analyze the amount of fuel wetting the port wall. The calculations are performed for a port-injection engine, and the differences of fuel behavior with respect to swirl control valve opening and wall temperature are discussed.

The EHD lubrication model of connecting rod big end bearings is compared with experiments using an automotive diesel engine. The axial load and the bending moment near the middle of rod length were derived from strain measurements and compared with the theoretical results based on engine dynamics. Although oscillation appeared on bending moment at 5000 rpm, the theoretical load almost agreed with the experiment. The EHD lubrication theory and the experiments were compared by the histories of clearances and the journal center orbits in the bearing. The theoretical results agreed well with the experimental one. The deformation of the bearing appeared both in the theory and in the experiment at 3000 rpm or above; these results confirm the necessity of the EHD lubrication theory.

Temperature distributions on the surface of a connecting rod big end bearing were measured to understand the margin to the allowable limiting temperature. The results show that the temperature difference between the bearing surface and the feed oil is independent of the engine load but quadratically increased with the engine speed, and that the bearing surface temperature on the rod side is higher than those on the cap side, and that the high temperature regions appeared near the edges on the rod side of the bearing under high speed operations. The results were analyzed by the observation of rubbing traces on the bearing surface and the EHD lubrication theory.