Search Results

As part of the U.S. Environmental Protection Agency’s (EPA’s) continuing assessment of advanced light-duty automotive technologies in support of regulatory and compliance programs, a development project was started to study various test methods to benchmark Electric Drive Units (EDUs) consisting of an electric motor, inverter and a speed-reduction gearset. Several test methods were identified for consideration, including both in-vehicle testing of the complete EDU and stand-alone testing of the EDU and its subcomponents after removal from the vehicle. In all test methods explored, sweeps of speed and torque test points were conducted while collecting key EDU data required to determine efficiency, including motor torque and speed, direct current (DC) battery voltage and current into the inverter, and three-phase alternating current (AC) phase voltages and currents out of the inverter and into the electric motor.

The United States Environmental Protection Agency’s (U.S. EPA’s) National Vehicle and Fuel Emissions Laboratory (NVFEL) has been developing new approaches for use in screening emissions from various types of new and in-use (used) engines to investigate if their exhaust emissions comply with federal emission standards. If the results from screening tests suggest anything unusual, EPA’s compliance program could investigate further to determine if that particular engine group or family should receive more rigorous compliance testing and analysis. In 2019, the EPA finished developing a means to screen the emissions of marine outboard engines, including the use of specialized equipment, laboratory methods, and procedures capable of controlling outboard marine engines to screen whether their exhaust is in line with appropriate emission standards.

As part of the U.S. Environmental Protection Agency’s (EPA’s) continuing assessment of advanced light-duty (LD) automotive technologies to support the setting of appropriate national greenhouse gas (GHG) standards and to evaluate the impact of new technologies on in-use emissions, a 2016 Honda Civic with a 4-cylinder 1.5-liter L15B7 turbocharged engine and continuously variable transmission (CVT) was benchmarked. The test method involved installing the engine and its CVT in an engine-dynamometer test cell with the engine wiring harness tethered to its vehicle parked outside the test cell. Engine and transmission torque, fuel flow, key engine temperatures and pressures, and onboard diagnostics (OBD)/Controller Area Network (CAN) bus data were recorded.

The use of devices to reduce aerodynamic drag on large trailers and save fuel in long-haul, over-the-road freight operations has spurred innovation and prompted some trucking fleets to use them in combinations to achieve even greater gains in fuel-efficiency. This paper examines aerodynamic performance and potential drag reduction benefits of using trailer aerodynamic components in combinations based upon wind tunnel test data. Representations of SmartWay-verified trailer aerodynamic components were tested on a one-eighth scale model of a class 8 sleeper tractor and a fifty three foot, van trailer model. The open-jet wind tunnel employed a rolling floor to reduce floor boundary layer interference. The drag impacts of aerodynamic packages are evaluated for both van and refrigerated trailers. Additionally, the interactions between individual aerodynamic devices is investigated.

In 2015 the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Transportation's National Highway Traffic Safety Administration (NHTSA) proposed a new steady-state engine dynamometer test procedure by which heavy-duty engine manufacturers would be required to create engine fuel rate versus engine speed and torque “maps”.[1] These maps would then be used within the agencies' Greenhouse Gas Emission Model (GEM)[2] for full vehicle certification to the agencies' proposed heavy-duty fuel efficiency and greenhouse gas (GHG) emissions standards. This paper presents an alternative to the agencies' proposal, where an engine is tested over the same duty cycles simulated in GEM. This paper explains how a range of vehicle configurations could be specified for GEM to generate engine duty cycles that would then be used for engine testing.

In designing a regulatory vehicle simulation program for determining greenhouse gas (GHG) emissions and fuel consumption, it is necessary to estimate the performance of technologies, verify compliance with the regulatory standards, and estimate the overall benefits of the program. The agencies (EPA/NHTSA) developed the Greenhouse Gas Emissions Model (GEM) to serve these purposes. GEM is currently being used to certify the fuel consumption and CO2 emissions of the Phase 1 rulemaking for all heavy-duty vehicles in the United States except pickups and vans, which require a chassis dynamometer test for certification. While the version of the GEM used in Phase 1 contains most of the technical and mathematical features needed to run a vehicle simulation, the model lacks sophistication. For example, Phase 1 GEM only models manual transmissions and it does not include engine torque interruption during gear shifting.

The performance of a commercial Cu-zeolite SCR catalyst after differing degrees of hydrothermal aging (aged for 72 hours at 500, 700 and 800°C with 10% moisture balanced with air) was studied by spatially resolving different key reactions using gas-phase FTIR measurements. Gases were sampled along a channel at different positions and analyzed using FTIR, which overcomes the interference of water and nitrogen on ammonia concentration detection encountered in standard mass spectrometer-based spatial resolution measurements. The NO:NO₂ concentration ratio was changed so that the standard (NO:NO₂ = 1:0), fast (NO:NO₂ = 1:1) and NO₂ (NO:NO₂ = 0:1) SCR reactions could be investigated as a function of the catalyst's hydrothermal aging extent. In addition, the effects of hydrothermal aging on the activity of NH₃ and NO oxidation were also investigated. Hydrothermal aging had little effect on NO oxidation activity.

Unique silver/alumina (Ag-Al₂O₃) catalysts developed using high-throughput discovery techniques in collaboration with BASF Corporation were investigated at General Motors Corporation under simulated lean-burn engine exhaust feed conditions for the selective catalytic reduction of NOx using hydrocarbons (HC-SCR). Hydrocarbon mixtures were used as the reductant to model the multi-component nature of diesel fuel and gasoline. Previous work has shown promising HC-SCR results in both laboratory reactor and engine dynamometer testing. This report investigates several aspects of HC-SCR catalyst durability, including thermal durability, sulfur tolerance, and hydrocarbon deactivation.

At the current state of diesel engine technology, all diesel engines require some sort of NOx control device to comply with Tier II Bin 5 light-duty or 2010 heavy-duty NOx emission standards. Selective Catalytic Reduction of NOx with hydrocarbons (HC-SCR) to reduce NOx from diesel exhaust emissions is an attractive technology for lean NOx control, especially when diesel fuel is used as the reductant. However, it has been reported that when diesel fuel is used as the reductant catalyst deactivation occurred. Even though this kind of deactivation is reversible at high enough temperatures, it is a deficiency that needs to be overcome for the successful implementation of the technology. We studied the HC-SCR catalyst deactivation using diesel fuel as the reductant. The variables investigated included catalyst temperature, HC:NOx ratio, NOx concentration, and space velocity. The results showed that one single parameter can be used to measure the catalyst deactivation: the HC-SCR activity.

To comply with Tier II Bin 5 light-duty or 2010 heavy-duty NOx emission standards, all diesel engines require some sort of NOx control device. Selective Catalytic Reduction of NOx with hydrocarbons (HC-SCR) to reduce NOx from diesel exhaust emissions is an attractive technology for lean NOx control, especially when diesel fuel is used as the reductant. However, it has been reported that when diesel fuel is used as the reductant catalyst deactivation occurred (1). In a companion paper, we demonstrated that the HC-deactivation is caused by the mismatch of the adsorption and desorption processes of either the reactants or the products of a normal SCR reaction (2). In this paper, we probe the nature of the catalyst deactivation with various reductants. Both hydrocarbons and oxygenates were used as the reductants. The deactivation or the mismatch in adsorption and desorption rates is molecular size or chain length dependent.

A unique silver/alumina selective catalytic reduction (SCR) catalyst which used hydrocarbons (HC-SCR) to reduce NOx emissions was investigated. Diesel fuel or ethanol were used as the reductants to evaluate catalyst performance. Several full size 5.0L monolith 2.0 and 3.0 wt.% Ag2O-Al2O3 catalysts were created. Testing was conducted using a 6.6L Duramax turbocharged heavy duty diesel engine. Dynamometer testing on the heavy duty FTP and SET 13 transient test cycles was conducted. The NOx conversion efficiency was evaluated as a function of catalyst volume, inlet cone angle, hydrocarbon to NOx ratio (HC:NOx), and space velocity. Oxygen effects on the NOx reaction and the HC slip past the HC-SCR catalyst were also determined. An FTIR was used to evaluate unregulated emissions. Testing on the heavy duty FTP and SET 13 test cycles, with diesel fuel as the reductant, resulted in a 60% and 65% NOx conversion reduction respectively.

A kinetic carbon monoxide (CO) emission model is developed to simulate engine out CO emissions for conventional diesel combustion. The model also incorporates physics governing CO emissions for low temperature combustion (LTC). The emission model will be used in an integrated system level model to simulate the operation and interaction of conventional and low temperature diesel combustion with aftertreatment devices. The Integrated System Model consists of component models for the diesel engine, engine-out emissions (such as NOx and Particulate Matter), and aftertreatment devices (such as DOC and DPF). The addition of CO emissions model will enhance the capability of the Integrated System Model to predict major emission species, especially for low temperature combustion. In this work a CO emission model is developed based on a two-step global kinetic mechanism [8].

Beginning in 2007, heavy-duty engine manufacturers in the U.S. have been responsible for verifying the compliance on in-use vehicles with Not-to-Exceed (NTE) standards under the Heavy-Duty In-Use Testing Program (HDIUT). This in-use testing is conducted using Portable Emission Measurement Systems (PEMS) which are installed on the vehicles to measure emissions during real-world operation. A key component of the HDIUT program is the generation of measurement allowances which account for the relative accuracy of PEMS as compared to more conventional, laboratory based measurement techniques. A program to determine these measurement allowances for gaseous emissions was jointly funded by the U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and various member companies of the Engine Manufacturer's Association (EMA).

In order to understand the flow and wind noise characteristics generated by the outside rearview (OSRV) mirror, a series of wind noise measurements for two production mirrors was conducted at the GM Aerodynamics Lab (GMAL) wind tunnel. These measurements included the time-averaged static pressures, surface noise sources, and far field propagation noise. The data obtained in this investigation will be used for future CFD numerical validations. The two mirrors chosen for the test are the GMT360 (a truck mirror) and the GMX320 (a sedan mirror). The test mirror was mounted on an elevated table which was specially designed for the current project to avoid any significant flow boundary layer buildup on the wind tunnel floor. The test conditions reported in this paper include four inlet speeds of 30, 50, 70 and 90 mph at 0 yaw angle. To record the wind noise sources, nine surface flush-mount microphones were used.

This paper describes a computational and experimental effort to document the detailed flow field around a pickup truck. The major objective was to benchmark several different computational approaches through a series of validation simulations performed at Clemson University (CU) and overseen by those performing the experiments at the GM R&D Center. Consequently, no experimental results were shared until after the simulations were completed. This flow represented an excellent test case for turbulence modeling capabilities developed at CU. Computationally, three different turbulence models were employed. One steady simulation used the realizable k-ε model. The second approach was an unsteady RANS simulation, which included a turbulence closure model developed in-house. This simulation captured the unsteady shear layer rollup and breakdown over the front of the hood that was expected and seen in the experiments but unattainable with other off-the-shelf turbulence models.

A unique catalyst developed using high-throughput discovery techniques in collaboration with BASF Corporation and Accelrys, Inc. was investigated at General Motors under simulated diesel engine exhaust feed conditions for the selective catalytic reduction of NOx. A hydrocarbon mixture was used as the reductant to model the multi-component nature of diesel fuel and the catalyst was evaluated over a wide range of temperatures (150 - 550°C) relevant to light-duty diesel exhaust. This report investigates the effects of NOx (as NO or NO2), hydrocarbon concentration level (HC:NOx ratio), oxygen concentration, NO concentration, catalyst space velocity, catalyst temperature, and the co-presence of hydrogen on steady-state NOx reduction activity. Using these results, a control strategy was developed to maximize NOx conversion over the wide-ranging exhaust conditions likely to be encountered in light-duty diesel applications.

The two most common NOx reducing technologies, in an oxygen abundant exhaust stream, are urea selective catalytic reduction urea-SCR and lean NOx trap (LNT) catalysts. Each technology has advantages and disadvantages. Another selective catalytic reduction (SCR) catalyst that uses hydrocarbons (HC-SCR), specifically diesel fuel, as the reductant to reduce NOx emissions was investigated. This catalyst is a result of a high throughput discovery project and conducted in cooperation with BASF, Accelrys and funded by the Department of Energy (DOE.) Several full size 5.0L monolith catalysts were made and evaluated using a V6 turbo charged diesel engine connected to a dynamometer running light-duty transient test cycles. The NOx efficiency on the HWYFET and US06 tests were measured to be 92% and 76% respectively. The FTP was 60% on a weighted basis.

In 2005, the United States Environmental Protection Agency (EPA) and Southwest Research Institute (SwRI) embarked on a mission to help the city of Beijing, China, clean its air. Working with the Beijing Environmental Protection Bureau (BEPB), the effort was a pilot diesel retrofit demonstration program involving three basic retrofit technologies to reduce particulate matter (PM). The three basic technologies were the diesel oxidation catalyst (DOC), the flowthrough diesel particulate filter (FT-DPF), and the wallflow diesel particulate filter (WF-DPF). The specific retrofit systems selected for the project were verified through the California Air Resources Board (CARB) or the EPA verification protocol [1]. These technologies are generally verified for PM reductions of 20-40 percent for DOCs, 40-50 percent for the FT-DPF, and 85 percent or more for the high efficiency WF-DPF.

The effects of varying nozzle spray angle and rail pressure on emissions and thermal efficiency each were explored using a 103-mm bore direct-injection single-cylinder diesel engine. Spray angles from 120° to 158° significantly changed the spray targeting within the 16:1 compression ratio reentrant-shaped piston bowl. At one part load operating condition injection timing was varied over a range of 15° to 30° btc to investigate pre-mixed compression ignition (PCI) combustion with 800 bar rail pressure while varying EGR to maintain a constant low NOx emission index of 0.4 g/kg. The observed trends are explained by the combined effects of spray angle and injection timing and, in particular, the calculated amount of liquid spray that misses the piston bowl is directly linked to the measured increases in HC, CO, and smoke emissions and a reduction in thermal efficiency.

Current SAE practices for evaluating potential improvements in fuel economy on heavy-duty vehicles rely on gravimetric measurements of fuel tanks. However, the recent evolution of portable emissions measurement systems (PEMS) offers an alternative means of evaluating real-world fuel economy that may be faster and more cost effective. This paper provides a direct comparison of these two methods based on a recent EPA study conducted at Southwest Research Institute. More than 228 on-road tests were performed on two pairs of class 8 tractor-trailers according to SAE test procedure J1321 in an assessment of various chassis components designed to reduce drag losses on the vehicle. During these tests, SEMTECH-D™ portable emissions measurement systems from Sensor's, Incorporated were operating in each of the vehicles to evaluate emissions and to provide a redundant measure of fuel economy.