Search Results

Until recently, dry cargo has been unloaded from trucks by use of compressed air. By making the automotive engine act partly as an air compressor during the unloading operation, the auxiliary air compressor mounted on the tractor frame can be eliminated. This paper, in describing the dual diesel, discusses operating characteristics, cycle analysis, and operational problems.

Most environments inhabited by living beings have dust. Much of that dust comes from the continuous flaking of our own skin and atmosphere borne particles of submicron size. Dust mites seem to play an important role in integrating fine scale dust, which they consume to grow, resulting in larger length scale dust. Dust continues to agglomerate and grow. Air filters are designed to remove dust and control dust agglomeration. We report a simple scaling law, based on kinematic simulations of dust filtration through a one dimensional idealized filter. The results reveal insights regarding how filters may clog in time. Our results may be of use to someone interested in designing customized air filters for optimum dust removal in an environment with a known dust distribution.

This paper reports the development of new fuel ignition quality and combustion experiments performed using the Ignition Quality Tester (IQT). Prior SAE papers (961182, 971636, 1999-01-3591, and 2001-01-3527) documented the development of the IQT constant volume combustion chamber experimental apparatus to measure ignition qualities of diesel-type fuels. ...The ASTM International test method D6890 was developed around the IQT device to allow the rapid determination of derived cetane number (DCN).

This study evaluated the bending fatigue performance of a modified SAE 4320 steel as a function of carburizing technique. S-N curves and endurance limits were established by fatigue testing modified Brugger-type specimens that are designed to simulate a single gear tooth. ...Fatigue endurance limits in excess of 1400 MPa had previously been achieved in gas-carburized SAE 4320 steels by reheat treatments and reductions in high-oxidation potential elements. The level of improvement observed in this study suggests that any of these advanced processing techniques can allow significant size reductions and weight savings in automotive transmission gears.

The electronics integration challenges are presented in the context of the U.S. medium duty and heavy duty automotive industry but have broad applicability to other heavy vehicles and markets worldwide. SAE and ISO forums are needed to address these issues.

During product definition, particular emphasis was placed on target markets, customer input to design, engineering and manufacturing processes, concurrent engineering and extensive mechanical and thermal analyses.

The phenomenon is a multi-disciplinary one which involves several aspects of physical sciences and engineering. This process is a slow progressive phenomenon with its detrimental effects being felt after severe damage has already occurred.

The simulation tool used is SIMPLEV 3.1 developed by the DOE Idaho National Engineering Laboratory, which runs a time-based simulation on a set of parameter files for an (hybrid) electric vehicle.

Fracture split forged steel connecting rods are utilized in many new high performance automotive engines to increase durability. Higher strength levels are needed as the power density increases. Fracture splitting without plastic deformation is necessary for manufacturability. Metallurgical design is a key for achieving the required performance levels. Several medium carbon steels containing 0.07 wt pct P, 0.06 wt pct S and various amounts of Mn, Si, V, and N were produced by vacuum induction melting laboratory heats and hot working the cast ingots into plates. The plates were cooled at varying rates to simulate typical cooling methods after forging. Microstructures were generally ferrite and pearlite as evaluated by light optical and scanning electron microscopy. Mechanical properties were determined by standard tensile tests, high strain rate notched tensile tests, and Charpy V-notch impact tests to assess “splittability”.

A dynamic simulation of a school bus powertrain has been constructed for the purpose of assisting in the development of engine control strategies. With some extensions, this model can also be used as a first approximation to support the development of transmission shift control strategies, predict vehicle performance and drivability as well as estimate transient loads on the powertrain components. The simulation was constructed using the Matlab* computing environment along with the Simulink* toolbox, a package for the graphical development of dynamic simulation models. The vehicle model was validated against test data measured in the target vehicle powered by a natural gas engine to ensure that the simulation model yielded sensible predictions of the dynamic powertrain behavior. Equipped with a validated model, the control engineer can now use the simulation tool to assist in algorithm development. Sample applications are illustrated.

Previous work on the cooling jackets of the Cummins L10 engine revealed flow separation, and low coolant velocities in several critical regions of the cylinder head. The current study involved the use of detailed cooling jacket temperature measurements, and finite element heat transfer analysis to attempt the identification of regions of pure convection, nucleate boiling, and film boiling. Although difficult to detect with certainty, both the measurements and analysis pointed strongly to the presence of nucleate boiling in several regions. Little or no evidence of film boiling was seen, even under very high operating loads. It was thus concluded that the regions of seemingly inadequate coolant flow remained quite effective in controlling cylinder head temperatures. The Cummins L10 upon which this study has focused is an in-line six cylinder, four-stroke direct injection diesel engine, with a displacement of 10 liters.

Joint development of the adiabatic engine by Cummins Engine Company and the U. S. Army began with a feasibility analysis ten years ago. The effort was initially driven by the expectation of substantial performance improvement, a reduction in cooling system size, and several additional benefits. Program emphasis turned quickly to experimentation with the goal of demonstrating the feasibility of the adiabatic engine in working hardware. Several significant achievements were realized as have been reported earlier. Further development of the adiabatic engine is expected to be more evolutionary, paced by available technology in the areas of materials and tribology. Analysis capability necessary for insulated engine development has been found to be inadequate. Additional effort has gone into the development and validation of insulated engine analysis tools, both for cycle simulation and structural modeling.

Two turbocompound diesel engines were assembled and dynamometer tested in preparation for vehicle tests. Both engines met the 1980 California gaseous emission requirement and achieved a minimum BSFC of .313 lb/bhp-hr and a BSFC at rated conditions of .323 lb/bhp-hr. These engines were then installed in Class VIII heavy-duty vehicles to determine the fuel consumption and performance characteristics. Fuel consumption testing showed a 14.8% improvement for the turbocompound engine in comparison to a production NTC-400 used as a baseline. The turbocompound engine also achieved lower noise levels, improved drive-ability, improved gradeability, and moderately increased engine retardation. The second turbocompound engine was placed in commercial service and accumulated 50,000 miles on a cross-country route without malfunction. Tank mileage revealed a 15.92% improvement over a production NTCC-400 which was operating on the same route.

The objective of the work described here is to test the performance of closed-loop controlled, heavy-duty CNG engines in-use, on fuels of different methane content; and to compare their performance with similar diesel vehicles. Performance is measured in terms of pollutant emissions, fuel economy, and driveability. To achieve this objective, three buses powered by closed-loop controlled, dedicated natural gas engines were tested on the heavy-duty chassis dynamometer facility at the Colorado Institute for Fuels and High Altitude Engine Research (CIFER). Emissions of regulated pollutants (CO, NOx, PM, and THC or NMHC), as well as emissions of alde-hydes for some vehicles, are reported. Two fuels were employed: a high methane fuel (90%) and a low methane fuel (85%). It was found that the NOx, CO, and PM emissions for a given cycle and vehicle are essentially constant for different methane content fuels.

Methane emissions from lean-burn natural gas engines can be relatively high. As natural gas fueled vehicles become more prevalent, future regulations may restrict these emissions. Preliminary reports indicated that conventional, precious metal oxidation catalysts rapidly deactivate (in less than 50 hours) in lean-burn natural gas engine exhaust. This investigation is directed at quantifying this catalyst deactivation and understanding its cause. The results may also be relevant to oxidation of lean-burn propane and gasoline engine exhaust. A platinum/palladium on alumina catalyst and a palladium on alumina catalyst were aged in the exhaust of a lean-burn natural gas engine (Cummins B5.9G). The engine was fueled with compressed natural gas. Catalyst aging was accomplished through a series of steady state cycles and heavy-duty transient tests (CFR 40 Part 86 Subpart N) lasting 10 hours. Hydrocarbons in the exhaust were speciated by gas chromatography.

Natural gas presents several challenges to engine manufacturers for use as a heavy-duty, lean burn engine fuel. This is because natural gas can vary in composition and the variation is large enough to produce significant changes in the stoichiometry of the fuel and its octane number. Similarly, operation at high altitude can present challenges. The most significant effect of altitude is lower barometric pressure, typically 630 mm Hg at 1600 m compared to a sea level value of 760 mm. This can lower turbocharger boost at low speeds leading to mixtures richer than desired. The purpose of this test program was to determine the effect of natural gas composition and altitude on regulated emissions and performance of a Cummins B5.9G engine. The engine is a lean-burn, closed loop control, spark ignited, dedicated natural gas engine. For fuel composition testing the engine was operating at approximately 1600 m (5,280 ft) above sea level.

Regulated emissions (THC, CO, NOx, and PM) and particulate SOF and sulfate fractions were determined for a 1995 Detroit Diesel Series 50 urban bus engine at varying fuel sulfur levels, with and without catalytic converters. When tested on EPA certification fuel without an oxidation catalyst this engine does not appear to meet the 1994 emissions standards for heavy duty trucks, when operating at high altitude. An ultra-low (5 ppm) sulfur diesel base stock with 23% aromatics and 42.4 cetane number was used to examine the effect of fuel sulfur. Sulfur was adjusted above the 5 ppm level to 50, 100, 200, 315 and 500 ppm using tert-butyl disulfide. Current EPA regulations limit the sulfur content to 500 ppm for on highway fuel. A low Pt diesel oxidation catalyst (DOC) was tested with all fuels and a high Pt diesel oxidation catalyst was tested with the 5 and 50 ppm sulfur fuels.

The technical objectives of the Clean Snowmobile Challenge 2000 are to modify a snowmobile to reduce the hydrocarbon, carbon monoxide and noise emissions by 50%, 25% and below 74 dB at 50 feet, respectively, while maintaining or exceeding current performance with a 500 cc two-stoke or 800 cc four-stroke. CSC2000 was the first of its kind competition held by the Society of Automotive Engineers. To meet these goals, the Colorado School of Mines team installed a dual-port fuel injection system, automotive catalytic converter, and noise absorbing foam on the 1997, 488 cc, air-cooled two-stroke Polaris Indy snowmobile provided.

AISI-4140H steel has been used as articulated piston crown material in heavy-duty engines. With the driving force for reducing manufacturing cost, microalloyed steel (MAS) was identified as a low-cost material to replace 4140H steel. In order to determine the feasibility of using MAS to replace 4140H steel, a test program was initiated to fully evaluate the material properties of MAS and to compare them to those of the baseline 4140H steel. The physical and mechanical properties of both materials from room temperature to 550°C were evaluated. The effect of long term thermal exposure on the material properties was also studied. Some engine tests were also conducted to evaluate the performance of the articulated pistons made with both materials. The inherently lower strength of MAS as compared to 4140H steel, requires a total re-design of the piston for the utilization of MAS as a low-cost replacement material for 4140H steel.

Emissions of six 32 passenger transit buses were characterized using one of the West Virginia University (WVU) Transportable Heavy Duty Emissions Testing Laboratories, and the fixed base chassis dynamometer at the Colorado Institute for Fuels and High Altitude Engine Research (CIFER). Three of the buses were powered with 1997 ISB 5.9 liter Cummins diesel engines, and three were powered with the 1997 5.9 liter Cummins natural gas (NG) counterpart. The NG engines were LEV certified. Objectives were to contrast the emissions performance of the diesel and NG units, and to compare results from the two laboratories. Both laboratories found that oxides of nitrogen and particulate matter (PM) emissions were substantially lower for the natural gas buses than for the diesel buses. It was observed that by varying the rapidity of pedal movement during accelerations in the Central Business District cycle (CBD), CO and PM emissions from the diesel buses could be varied by a factor of three or more.