Search Results

In a recent study, quantitative measurements were presented of in-cylinder spatial distributions of mixture equivalence ratio in a single-cylinder light-duty optical diesel engine, operated with a non-reactive mixture at conditions similar to an early injection low-temperature combustion mode. In the experiments a planar laser-induced fluorescence (PLIF) methodology was used to obtain local mixture equivalence ratio values based on a diesel fuel surrogate (75% n-heptane, 25% iso-octane), with a small fraction of toluene as fluorescing tracer (0.5% by mass). Significant changes in the mixture's structure and composition at the walls were observed due to increased charge motion at high swirl and injection pressure levels. This suggested a non-negligible impact on wall heat transfer and, ultimately, on efficiency and engine-out emissions.

Many recent studies have shown that the Reactivity Controlled Compression Ignition (RCCI) combustion strategy can achieve high efficiency with low emissions. However, it has also been revealed that RCCI combustion is difficult at high loads due to its premixed nature. To operate at moderate to high loads with gasoline/diesel dual fuel, high amounts of EGR or an ultra low compression ratio have shown to be required. Considering that both of these approaches inherently lower thermodynamic efficiency, in this study natural gas was utilized as a replacement for gasoline as the low-reactivity fuel. Due to the lower reactivity (i.e., higher octane number) of natural gas compared to gasoline, it was hypothesized to be a better fuel for RCCI combustion, in which a large reactivity gradient between the two fuels is beneficial in controlling the maximum pressure rise rate.

This research explored methods to reduce regulated emissions in a small-bore, direct-injection diesel engine. Swirl was used to influence mixing of the spray plumes, and alternative fuels were used to study the effects of oxygenated and water microemulsion diesel fuels on emissions. Air/fuel mixing enhancement was achieved in the running engine by blocking off a percentage of one of the two intake ports. The swirl was characterized at steady-state conditions with a flowbench and swirl meter. Swirl ratios of 1.85, 2.70, and 3.29 were studied in the engine tests at full load with engine speeds of 1303, 1757, and 1906 rev/min. Increased swirl was shown to have negative effects on emissions due to plume-to-plume interactions. Blends of No. 2 diesel and biodiesel were used to investigate the presence of oxygen in the fuel and its effects on regulated emissions. Pure No. 2 diesel fuel, a 15% and a 30% biodiesel blend (by weight) were used.

An experimental and numerical characterization has been conducted of a high-pressure common rail diesel fuel injection system. The experimental study was performed using a common rail system with the capability of producing multiple injections within a single cycle. The injector used in the experiments had a single guided multi-hole nozzle tip. The diesel sprays were injected into a pressurized chamber with optical access at ambient temperature. The gas density in the chamber was representative of the density in an HSDI diesel engine at the time of injection. Single, pilot, and multiple injection cases were studied at different rail pressures and injection durations. Images of the transient sprays were obtained with a high-speed digital camera. From these images spray tip penetration and cone angles were obtained directly. Also spray droplet sizes were derived from the images using a light extinction method (LEM).

Rate shaping of the fuel injection process is known to significantly impact emissions production in diesel engines. To demonstrate the ability of multidimensional engine modeling to quantify and explain the effect of rate shaping and injection duration, three injection profiles typical of common diesel fuel injection systems were investigated for three injection durations and injection timings. The present study uses an improved version of the KIVA-II engine simulation code employing the characteristic time combustion model, the Kelvin-Helmholtz and the Rayleigh-Taylor spray atomization mechanisms, the extended Zeldovich thermal NOx production model, and a single species soot model.

Studies on the effects of methyl soyate (biodiesel) blends with #2 diesel fuel in conjunction with various high pressure injection schemes were conducted on a single cylinder version of the Caterpillar 3400 series heavy duty diesel engine. Engine operating conditions at both high and low loads were investigated. Experiments were performed over a range of injection timings allowing particulate versus NOx trade-off curves to be generated. Phillips 66 certified #2 diesel fuel was used as the baseline; mixtures of 20% and 40% by volume of methyl soyate with the baseline fuel were used as the biodiesel blends. A blend of 20% by volume octadecene (a hydrocarbon fuel that is representative of the biodiesel hydrocarbon's composition but without the oxygen) in #2 diesel fuel was also investigated to help determine the mechanisms of emissions reduction.

A computer model developed for describing multicomponent fuel vaporization, and ignition in diesel engines has been applied in this study to understand cold-starting and the parameters that are of significant influence on this phenomena. This research utilizes recent improvements in spray vaporization and combustion models that have been implemented in the KIVA-II CFD code. Typical engine fuels are blends of various fuels species, i.e., multicomponent. Thus, the original single component fuel vaporization model in KIVA-II was replaced by a multicomponent fuel vaporization model (based on the model suggested by Jin and Borman). The modelhas been extended to model diesel sprays under typical diesel conditions, including the effect of fuel cetane number variation. Necessary modifications were carried out in the atomization and collision sub-models. The ignition model was also modified to account for fuel composition effects by modifying the Shell ignition model.