Search Results

Accurate evaluation of vehicles' transient total power requirement helps achieving further improvements in vehicle fuel efficiency. When operated, the air-conditioning (A/C) system is the largest auxiliary load on a vehicle, therefore accurate evaluation of the load it places on the vehicle's engine and/or energy storage system is especially important. Vehicle simulation models, such as "Autonomie," have been used by OEMs to evaluate vehicles' energy performance. However, the load from the A/C system on the engine or on the energy storage system has not always been modeled in sufficient detail. A transient A/C simulation tool incorporated into vehicle simulation models would also provide a tool for developing more efficient A/C systems through a thorough consideration of the transient A/C system performance. The dynamic system simulation software MATLAB/Simulink® is frequently used by vehicle controls engineers to develop new and more efficient vehicle energy system controls.

As global automobile manufacturers prepare for the phase-out of R134a in Europe, they must address the issue of using the new refrigerant for European sales only or launching the product worldwide. Several factors play into this decision, including cost, service, risk, customer satisfaction, capacity, efficiency, etc. This research effort addresses the minimal vehicle-level hardware differences necessary to provide a European solution of R1234yf while continuing to install R134a into vehicles for the rest of the world. It is anticipated that the same compressor, lubricant and condenser; most fluid transport lines; and in most cases the evaporator can be common between the two systems.

The automotive aftermarket represents a challenge for supply chain management when compared to traditional practices in the original equipment manufacturer (OEM) supply chain. This paper presents a case study for a Tier One automotive supplier’s challenges with inventory carrying costs, backorder risk, and supplier relationships for a rear seat entertainment system in the automotive aftermarket. It will also address the lean principles used to improve the business and increase material planning analyst productivity. A call for OEMs to examine their business practices is also included.

To obtain the maximum output power and fuel economy from an internal combustion engine, it is often necessary to detect engine knock and operate the engine at its knock limit. This paper presents the ability to detect knock using in-cylinder ionization signals on a large displacement, air-cooled, “V” twin motorcycle engine over the engine operational map. The knock detection ability of three different sensors is compared: production knock (accelerometer) sensor, in-cylinder pressure sensor, and ionization sensor. The test data shows that the ionization sensor is able to detect knock better than the production knock sensor when there is high mechanical noise present in the engine.

First LED headlamps will be released into the market in 2007. Special permissions allow this introduction although the official regulation is still under discussion in ECE. The LED technology for front lighting has entered into a new phase from theoretical, prototype status to real and practical applications. Additionally in Europe the legislation, which is under preparation, defines LED modules with one or more LED chips in a row which should be replaceable. With this boundary conditions headlamp suppliers needs to balance between an attractive and innovative styling, demanded by car manufacturers and the light performance to gurantee good visibility at night. The paper describes the methods how to design an LED headlamp with high efficiency by keeping in mind the parameters: packaging, weight, styling and light perfromance. Results with specific design proposals are shown.

This paper describes a front road wheel steer-by-wire system with two actuator motors on the rack and pinion assembly to move the road wheels. Dual actuators are used to provide actuator redundancy and to enhance the fault tolerance capability. When one actuator faults or fails, the other actuator is designed to work independently and maintain full system performance. The paper emphasizes control method to implement the motion control for the front road wheel steer-by-wire system with two actuators on the common load. The proposed dual servo synchronization motion control implements the angle tracking for the road wheel reference input by controlling two actuators synchronously and cooperatively. It includes two servo feedback control loops to track the common reference input. The angular position error between two feedback loops is compensated using a synchronized compensator.

During last 10-15 years we could have seen quite big changes in automotive lighting. The most important changes are: a) plastic materials mostly removed metal and glass material from lighting products raised heat issue of plastics materials b) escalation of competition between lighting suppliers (globalization, merging, …) decrease of time and cost for development of the new product as much as possible

High-power LEDs and LED headlamps have become a serious consideration for the automotive industry. White LEDs have achieved the required performance for initial automotive headlamp applications. However tradeoffs among several attributes such as efficiency, cost, weight and performance profoundly affect LED headlamp development and need to be addressed by vehicle manufacturers, lamp set makers and LED source suppliers in order for LED headlamps to be effective. The solutions to these tradeoffs relates to the behavior of the LED sources, the thermo-mechanical integration of LEDs in a headlamp environment and input from the vehicle manufacturer regarding styling and packaging for an LED headlamp on the respective targeted vehicles.

Steer-by-wire systems (SBW) offer the potential to enhance steering functionality by enabling features such as automatic lane keeping, park assist, variable steer ratio, and advanced vehicle dynamics control. The lack of a steering intermediate shaft significantly enhances vehicle architectural flexibility. These potential benefits led GM to include steer-by-wire technology in its next generation fuel cell demonstration vehicle, called “Sequel.” The Sequel's steer-by-wire system consists of front and rear electromechanical actuators, a torque feedback emulator for the steering wheel, and a distributed electronic control system. Redundancy of sensors, actuators, controllers, and power allows the system to be fault-tolerant. Control is provided by multiple ECU's that are linked by a fault-tolerant communication system called FlexRay. In this paper, we describe the objectives for fault tolerance and performance that were established for the Sequel.

Commonly, a significant event is detected when a normally stable engine parameter (ex. sensor voltage, sensor current, air flow, pedal position, fuel level, tire pressure, engine acceleration, etc.) transiently exceeds a calibrated detection threshold. Many implementations of detection thresholds rely on multi-input lookup tables or functions and are complex and difficult to calibrate. An approach is presented to minimize threshold calibration effort and complexity, while improving detection performance, by dynamically computing thresholds on-line based on current real-time data. Determining engine synchronization without a camshaft position sensor is presented as an illustrative application.

Although not completely understood, rotor distortion due to bolt-up is an issue commonly found in conventional brake rotor design. In this paper, bolt-up is addressed by utilizing optimization and contact analysis methods. These methods give greater insight to the contributing factors that influence bolt-up distortion. In particular, the optimization method defines the approximate geometric shape required for a brake rotor based on optimizing one or more variables. By utilizing the non-linear contact analysis method, the results from the optimization analysis are validated. In general, the results show that bolt-up distortion is not significantly affected by changing design features, variables or combinations of design features and variables. However, significant improvement in bolt-up distortion is noticed when changes are made to the brake rotor and the wheel bearing hub.

Modern automobiles utilize stabilizer bars to increase vehicle roll stiffness. Stabilizer bars are laterally mounted torsional springs which resist vertical displacement of the wheels relative to one another. A stabilizer bar is constructed in such a way that it will meet package constraints and fatigue requirements. In order to design a robust stabilizer bar, Taguchi's “Design of Experiment method” is used. The objective of this paper is to develop a robust stabilizer bar design that will maximize the fatigue life and the roll stiffness while minimizing weight. This study is based on results obtained by CAE analysis.

The era of the vehicle as a standalone non-connected entity is rapidly drawing to a close. The “Box” on four wheels is being opened to multiple communication channels based on consumer demand and expectations of the latest features, functions and content. Concurrently, automotive planners, marketers, engineers, and system architects are subject to increased complexity as a result of the rapidly evolving consumer electronics industry. This paper will discuss many of the limitations of existing automotive business models in attempting to successfully implement and meet consumer expectations. It will also propose a structural framework for automotive planners, marketers, engineers, and system architects to be able to better understand and predict consumer acceptance of electronics, multimedia features, and in-vehicle content access.

There are benefits of using ultra thin wall (UTW) substrates (i.e., 900/2, 400/4, etc) in lowering cost and emission level. However, the more fragile mechanical characteristics of the UTW present a challenge to design and manufacture of robust catalytic converters. This paper describes a method of canning trial, where a combined Design of Experiment / Monte-Carlo analysis method was used, to develop and validate a canning method for ultra thin wall substrates. Canning trials were conducted in two stages-- Prototype Canning Trial and Production Canning Trial. In Prototype Canning Trial, the root cause of substrate failure was identified and a model for predicting substrate failure was established. Key factors affecting scrap rate and gap capability were identified and predictions were performed on scrap rate and gap capability with the allowed variations in the key factors. The results provided guidelines in designing production line and process control.

Internal combustion engines are designed to maximize power subject to meeting exhaust emission requirements and minimizing fuel consumption. Maximizing engine power and fuel economy is limited by engine knock for a given air-to-fuel charge. Therefore, the ability to detect engine knock and run the engine at its knock limit is a key for the best power and fuel economy. This paper shows inaudible knock detection ability using in-cylinder ionization signals over the entire engine speed and load map. This is especially important at high engine speed and high EGR rates. The knock detection ability is compared between three sensors: production knock (accelerometer) sensor, in-cylinder pressure and ionization sensors. The test data shows that the ionization signals can be used to detect inaudible engine knock while the conventional knock sensor cannot under some engine operational conditions.

Application of Ultra Thin Wall (UTW) ceramic substrates in the catalytic converter system requires the canner and component manufacturers to better understand the root cause and physics behind substrate breakage during the canning process. For this purpose, a ceramic substrate strength study for shoebox design has been conducted within Visteon Corporation. Computer Numerical Control (CNC) machined top and bottom fixtures, with identical inner surfaces as shoebox converter upper and lower shells, were used to crush mat wrapped substrates. Thin film pressure sensor technology enables the recording of substrate surface pressure during the compression process. Shell rib, washcoat, canning speed and cell density effects on substrate failure have been experimentally investigated. The development of a mathematical model helps to identify a better indicator to evaluate the substrate strength in the canning process and establish the strength for uncoated & coated substrates.

Evolutionary Operation (EVOP) experimental design using Sequential Simplex method is an effective and robust means for determining the ideal process parameter (factor) settings to achieve optimum output (response) results. EVOP is the methodology of using on-line experimental design. Small perturbations to the process are made within allowable control plan limits, to minimize any product quality issues while obtaining information for improvement on the process. It is often the case in high volume production where issues exist, however off-line experimentation is not an option due to production time, the threat of quality issues and costs. EVOP leverages production time to arrive at the optimum solution while continuing to process saleable product, thus substantially reducing the cost of the analysis.

A motorized throttle model has been developed in block diagram form (Simulink®). Its primary input is the control signal to the throttle motor's electrical H-driver. The model's primary output is throttle position sensor signal. The model's utility for vehicle and engine simulations is proved with validation data. While a DC motor actuated positioning device is well known, special attention is paid to modeling subtle but significant physical characteristics. Further, the model is structured to overcome numerical simulation issues. The laboratory environment that connects a Powertrain Control Module (PCM) to vehicle powertrain simulation hardware is diagramed. This paper is useful to those modeling this and similar actuators as it points out pitfall avoidance for real time simulation issues. It avoids reliance on difficult-to-measure characteristics that cloud validation validity.

A fixed-base driving simulator with a 14-degree of freedom vehicle dynamics model was used to compare the lane tracking performance of test subjects using a joystick steering controller to that using a conventional steering wheel. Three driving situations were studied: a) straight-line highway driving, b) winding road driving (country road), and c) evasive maneuvering - a double lane change event. In addition, three different joystick force-feedback settings were evaluated: i) linear force feedback, ii) non-linear, speed sensitive force feedback and iii) no force feedback. A conventional steering wheel with typical passenger car force feedback tuning was used for all of the driving events for comparison.

Rising costs continue to be a problem within the automotive industry. One way to address these rising costs is through modularity. Modular systems provide the ability to achieve product variety through the combination and standardization of components. Modular design approaches used in development of vehicle electrical, electronic, and software (EES) systems allow sharing of architectures/modules between different product lines (vehicles). This modular design approach may provide economies of scale, reduced development time, reduced order lead-time, easier product diagnostics, maintenance and repair. Other benefits of this design approach include development of a variety of EES systems through component swapping and component sharing. In this paper, new optimization algorithms and software tools are presented that allow vehicle EES system design engineers to develop modular architectures/modules that can be shared across vehicle platforms (for OEMs) and across OEMs (for suppliers).