Search Results

This SAE Recommended Practice pertains to liquid level determination for any fluid compartment of off-road work machines as defined in SAE J1116 and ISO 6165.

This document establishes recommended practices to validate acceptable corrosion performance of metallic components and assemblies used in medium truck, heavy truck, and bus and trailer applications. The focus of the document is methods of accelerated testing and evaluation of results. A variety of test procedures are provided that are appropriate for testing components at various locations on the vehicle. The procedures incorporate cyclic conditions including corrosive chemicals, drying, humidity, and abrasive exposure. These procedures are intended to be effective in evaluating a variety of corrosion mechanisms as listed in Table 1. Test duration may be adjusted to achieve any desired level of exposure. Aggravating conditions such as joint rotation, mechanical stress, and temperature extremes are also considered. This document does not address the chemistry of corrosion or methods of corrosion prevention. For information in these areas, refer to SAE J447 or similar standard.

This specification covers polythioether rubber fuel resistant sealing compounds, supplied as a two-component system, which cure rapidly when exposed to a cure on demand (CoD) light source used to initiate a reaction that generates crosslinking of sealant polymers. Type 2 compounds also cure at ambient conditions, without light exposure.

This SAE Standard applies to horizontal earthboring machines of the following types: a. Auger Boring Machines b. Rod Pushers c. Rotary Rod Machines d. Impact Machines e. Directional Boring/Drilling Machines The illustrations used are for classification and are not intended to resemble a particular machine. Only basic working dimensions are given. They may be supplemented by the machine manufacturer. This document is based on existing commercial horizontal earthboring machines. This document does not apply to specialized mining machinery in SAE J1116, conveyors, tunnel boring machines, pipe jacking systems, and microtunnelers.

This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.

This SAE Standard establishes a uniform procedure and performance requirements for snowmobile fuel tanks.

This SAE Standard applies to the fuel consumption of non-propulsion engines used to drive exclusively the sweeping and cleaning functions of multi-engine sweepers and scrubbers as defined in SAE J2130-1 and SAE J2130-2.

This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull.

It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.

This SAE Recommended Practice covers all carburetors and throttle bodies used on permanently installed gasoline marine engines.

This SAE Standard covers the flexible components of marine engine wet exhaust systems from the connection at the engine exhaust manifold to the hull or overboard discharge fittings.

This document applies to off-road forestry work machines defined in SAE J1116 or ISO 6814.

This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.

This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors.

This SAE Standard covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from within the gasoline engine to the surrounding atmosphere.

This standard specifies the communications hardware and software requirements for fueling hydrogen surface vehicles (HSV), such as fuel cell vehicles, but may also be used where appropriate, with heavy-duty vehicles (e.g., busses) and industrial trucks (e.g., forklifts) with compressed hydrogen storage. It contains a description of the communications hardware and communications protocol that may be used to refuel the HSV. The intent of this standard is to enable harmonized development and implementation of the hydrogen fueling interfaces. This standard is intended to be used in conjunction with the hydrogen fueling protocols in SAE J2601 and nozzles and receptacles conforming with SAE J2600.

This SAE Recommended Practice provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system.

This SAE Standard is intended to provide personnel protection guidelines for skid steer loaders. This document is intended as a guide towards standard practice, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. This document provides performance criteria for newly manufactured loaders and it is not intended for in-service machines.

This SAE Recommended Practice covers the requirements for switches used in marine applications both under and over 50 V.

This SAE Standard provides a uniform method to calculate the lift capacity of scrap and material handlers, establishes definitions and specifies machine conditions for the calculations. This document applies to scrap and material handlers as defined in SAE J2506 that have a 360 degrees continuous rotating upper structure. It does not apply to equipment that is incapable of lifting a load completely off the ground. This document applies to those machines that are crawler, wheel, rail and pedestal or stationary mounted.

SAE J1362 presents graphical symbols for use on operator controls and other displays on off-road work machines as defined in SAE J1116 plus mobile cranes but excluding agricultural tractors. Symbols for agricultural tractors are covered by ASABE S304, ISO 3767-1, and ISO 3767-2.