Search Results

An experimental study was performed in a firing SI engine at conditions representative of the warmup phase of operation in which liquid gasoline films were established at various locations in the combustion chamber and the resulting impact on hydrocarbon emissions was assessed. Unique about this study was that it combined, in a firing engine environment, direct visual observation of the liquid fuel films, measurements of the temperatures these films were subjected to, and the determination from gas analyzers of burned and unburned fuel quantities exiting the combustion chamber - all with cycle-level resolution or better. A means of deducing the exhaust hydrocarbon emissions that were due to the liquid fuel films in the combustion chamber was developed. An increase in exhaust hydrocarbon emissions was always observed with liquid fuel films present in the combustion chamber.

An experimental study was performed to develop a more fundamental understanding of the effects of secondary air injection (SAI) on exhaust gas emissions and catalyst light-off characteristics during cold start of a modern SI engine. The effects of engine operating parameters and various secondary air injection strategies such as spark retardation, fuel enrichment, secondary air injection location and air flow rate were investigated to understand the mixing, heat loss, and thermal and catalytic oxidation processes associated with SAI. Time-resolved HC, CO and CO₂ concentrations were tracked from the cylinder exit to the catalytic converter outlet and converted to time-resolved mass emissions by applying an instantaneous exhaust mass flow rate model. A phenomenological model of exhaust heat transfer combined with the gas composition analysis was also developed to define the thermal and chemical energy state of the exhaust gas with SAI.

A prior study (Chon and Heywood, [1]) examined how the design and performance of spark-ignition engines evolved in the United States during the 1980s and 1990s. This paper carries out a similar analysis of trends in basic engine design and performance characteristics over the past decade. Available databases on engine specifications in the U.S., Europe, and Japan were used as the sources of information. Parameters analyzed were maximum torque, power, and speed; number of cylinders and engine configuration, cylinder displacement, bore, stroke, compression ratio; valvetrain configuration, number of valves and their control; port or direct fuel injection; naturally-aspirated or turbocharged engine concepts; spark-ignition and diesel engines. Design features are correlated with these engine’s performance parameters, normalized by engine and cylinder displacement.

Experiments were carried out to collect in-cylinder pressure data and microphone signals from a single-cylinder test engine using spark timingsbefore, at, and after knock onset for toluene reference fuels. The objective was to gain insight into the phenomena that determine knock onset, detected by an external microphone. In particular, the study examines how the end-gas autoignition process changes as the engine's spark timing is advanced through the borderline knock limit into the engine's knocking regime. Fast Fourier transforms (FFT) and bandpass filtering techniques were used to process the recorded cylinder pressure data to determine knock intensities for each cycle. Two characteristic pressure oscillation frequencies were detected: a peak just above 6 kHz and a range of peaks in the 15-22 kHz range. The microphone data shows that the audible knock signal has the same 6 kHz peak.

In an effort to both increase engine efficiency and generate new, consistent, and reliable data useful for the development of engine concepts, a modern single-cylinder 4-valve spark-ignition research engine was used to determine the response of indicated engine efficiency to combustion phasing, relative air-fuel ratio, compression ratio, and load. Combustion modeling was then used to help explain the observed trends, and the limitations on achieving higher efficiency. This paper analyzes the logic behind such gains in efficiency and presents correlations of the experimental data. The results are helpful for examining the potential for more efficient engine designs, where high compression ratios can be used under lean or dilute regimes, at a variety of loads.

An experimental study was carried out that qualitatively examined the mixture preparation process in port fuel injected engines. The primary variables in this study were intake valve lift, intake valve timing, injector spray quality, and injection timing. A special visualization engine was used to obtain high-speed videos of the fuel-air mixture flowing through the intake valve, as well as the wetting of the intake valve and head in the combustion chamber. Additionally, videos were taken from within the intake port using a borescope to examine liquid fuel distribution in the port. Finally, a simulation study was carried out in order to understand how the various combinations of intake valve lifts and timings affect the flow velocity through the intake valve gap to aid in the interpretation of the videos.

As part of ongoing research on hydrogen-enhanced lean burn SI engines, this paper details an experimental combustion system optimization program. Experiments focused on three key areas: the ignition system, in-cylinder charge motion produced by changes in the inlet ports, and uniformity of fuel-air mixture preparation. Hydrogen enhancement is obtained with a H2, CO, N2 mixture produced by a fuel reformer such as the plasmatron. The ignition system tests compared a standard inductive coil scheme against high-energy discharge systems. Charge motion experiments focused on the impact of different flow and turbulence patterns generated within the cylinder by restrictor plates at the intake port entrance, as well as novel inlet flow modification cones. The in-cylinder fluid motion generated by each configuration was characterized using swirl and tumble flow benches. Mixture preparation tests compared a standard single-hole pintle port fuel injector against a fine atomizing 12-hole injector.

As a part of the effort to comply with increasingly stringent emission standards, engine manufacturers strive to minimize engine oil consumption. This requires the advancement of the understanding of the characteristics, sources, and driving mechanisms of oil consumption. This paper presents a combined theoretical and experimental approach to separate and quantify different oil consumption sources in a production spark ignition engine at different speed and load conditions. A sulfur tracer method was used to measure the dependence of oil consumption on engine operating speed and load. Liquid oil distribution on the piston was studied using a Laser-Induced-Fluorescence (LIF) technique. In addition, important in-cylinder parameters for oil transport and oil consumption, such as liner temperatures and land pressures, were measured.

A spark-ignition engine friction model developed by Patton et al. in the late 1980s was evaluated against current engine friction data, and improved. The model, which was based on a combination of fundamental scaling laws and empirical results, includes predictions of rubbing losses from the crankshaft, reciprocating, and valvetrain components, auxiliary losses from engine accessories, and pumping losses from the intake and exhaust systems. These predictions were based on engine friction data collected between 1980 and 1988. Some of the terms are derived from lubrication theory. Other terms were derived empirically from measurements of individual friction components from engine teardown experiments. Recent engine developments (e.g., improved oils, surface finish on piston liners, valve train mechanisms) suggested that the model needed updating.

Engine oil consumption is an important source of hydrocarbon and particulate emissions in automotive engines. Oil evaporating from the piston-ring-liner system is believed to contribute significantly to total oil consumption, especially during severe operating conditions. This paper presents an extensive experimental and theoretical study on the contribution of oil evaporation to total oil consumption at different steady state speed and load conditions. A sulfur tracer method was used to measure the dependence of oil consumption on coolant outlet temperature, oil volatility, and operating speed and load in a production spark ignition engine. Liquid oil distribution on the piston was studied using a one-point Laser-Induced-Fluorescence (LIF) technique. In addition, important in-cylinder variables for oil evaporation, such as liner temperature and cylinder pressure, were measured. A multi-species cylinder liner oil evaporation model was developed to interpret the oil consumption data.

Engine oil consumption is recognized to be a significant source of pollutant emissions. Unburned or partially burned oil in the exhaust gases contributes directly to hydrocarbon and particulate emissions. In addition, chemical compounds present in oil additives poison catalytic converters and reduce their conversion efficiency. Oil consumption can increase significantly during critical non-steady operating conditions. This study analyzes the oil consumption behavior during ramp transients in load by combining oil consumption measurements, in-cylinder measurements, and computer-based modeling. A sulfur based oil consumption method was used to measure real-time oil consumption during ramp transients in load at constant speed in a production spark ignition engine. Additionally in-cylinder liquid oil behavior along the piston was studied using a one-point Laser-Induced-Fluorescence (LIF) technique.

The behavior of the liquid fuel impinging on the piston top of a direct-injected, spark-ignited (DISI) engine operating under stratified conditions is investigated using floodlight laser-induced fluorescence (LIF). The combustion chamber geometry offers wall-guided stratification using a high-pressure injector impinging on an inclined piston bowl. The LIF signal is collected through the bottom of the quartz piston, allowing observation of the footprint of the spray during and after spray development. Nitrogen gas is used to replace air in order to minimize oxygen quenching and increase the signal. The results show that at typical piston top temperatures expected in warmed-up operation (150-180 °C), a liquid film and ring around the area where the fuel jet impinges is present through the time of spark (20° before top center). The presence of the fuel film is not very sensitive to the surface temperature.

The characteristics of the combustion process in direct-injected, spark-ignited (DISI), stratified-operation engines, are intimately related to the fuel distribution in the combustion chamber. Engine performance, and particularly emissions of hydrocarbons, nitric oxides and particulate matter are strongly dependent on the manner in which the fuel charge is distributed. The present paper investigates the fuel distribution and combustion characteristics of a side-injected DISI engine under stratified operation and late injection, using optical diagnostics without compromising on the use of a realistic bowl geometry. Laser-induced fluorescence, laser-induced elastic scatter and color and luminosity visualization are employed to identify the relationship between fuel distribution and combustion characteristics.

A gasoline direct injection fuel spray was observed using a fired, optical access, square cross-section single cylinder research engine and high-speed video imaging. Spray interaction with the piston is described qualitatively, and the results are compared with Computational Fluid Dynamics (CFD) simulation results using KIVA-3V version 2. CFD simulations predicted that within the operating window for stratified charge operation, between 1% and 4% of the injected fuel would remain on the piston as a liquid film, dependent primarily on piston temperature. The experimental results support the CFD simulations qualitatively, but the amount of fuel film remaining on the piston appears to be under-predicted. High-speed video footage shows a vigorous spray impingement on the piston crown, resulting in vapor production.

Optimal design of modern direct injection spark-ignition engines depends heavily on the characteristics and distribution of the fuel spray. This study was designed to compliment imaging experiments of changes in the spray structure due to fuel volatility and operating conditions. Use of phase-Doppler particle analysis (PDPA) allows quantitative point measurements of droplet diameter and velocity. In agreement with imaging experiments, the results show that the spray structure changes not only with ambient gas density, which is often measured, but also with fuel temperature and volatility. The mean droplet diameter was found to decrease substantially with increasing fuel temperature and decreasing ambient density. Under conditions of low potential for vaporization, the observed trends in mean droplet sizes agree with published correlations for pressure-swirl atomizers.

Optimal design of modern direct injection spark-ignition engines depends heavily on the characteristics and distribution of the fuel spray. This study was designed to investigate changes in the spray properties due to fuel volatility and operating conditions using a firing optically-accessible engine with planar laser-induced fluorescence (PLIF) imaging. The results show that the spray structure changes not only with ambient gas density, which is often measured, but also with fuel temperature and volatility. As ambient pressure decreases and fuel temperature increases, the volatile ends of multi-component fuels evaporate quickly, disrupting the spray structure and producing a vapor core along the axis of the spray. Beyond a certain point, evaporation is rapid enough to expand the initial cone angle of the spray while causing a decrease in the overall spray width.

This study examines the scaling between engine performance, engine configuration, and engine size and geometry, for modern spark-ignition engines. It focuses especially on design features that impact engine breathing. We also analyze historical trends to illustrate how changes in technology have improved engine performance. Different geometric parameters such as cylinder displacement, piston area, number of cylinders, number of valves per cylinder, bore to stroke ratio, and compression ratio, in appropriate combinations, are correlated to engine performance parameters, namely maximum torque, power and brake mean effective pressure, to determine the relationships or scaling laws that best fit the data. Engine specifications from 1999 model year vehicles sold in the United States were compiled into a database and separated into two-, three-, and four-valves-per-cylinder engine categories.

In order to understand why emissions of Particulate Matter (PM) from Spark-Ignition (SI) automobiles peak during periods of transient operation such as rapid accelerations, a study of controlled, repeatable transients was performed. Time-resolved engine-out PM emissions from a modern four-cylinder engine during transient load and air/fuel ratio operation were examined, and the results could be fit in most cases to a first order time response. The time constants for the transient response are similar to those measured for changes in intake valve temperature, reflecting the strong dependence of PM emissions on the amount of liquid fuel in the combustion chamber. In only one unrepeatable case did the time response differ from a first order function: showing an overshoot in PM emissions during transition from the initial to the final steady state PM emission level.

Liquid fuel behavior in the cylinder impacts SI engine HC emissions particularly during engine start-up. Inflow of liquid fuel into the cylinder is largely determined by the flow and temperature environment in the intake port. Subsequent evaporation of fuel droplets in the cylinder prior to impact on the piston and cylinder liner reduces the amount of liquid fuel in the cylinder that is likely to contribute to HC emission and is therefore important. In this study, measurements of liquid fuel droplet characteristics in the vicinity of the intake valve of a firing SI engine were analyzed to estimate the amount and spatial distribution of in-cylinder evaporation of liquid fuel prior to droplet impact on the cylinder liner or piston. A one-dimensional fuel droplet evaporation model was developed to predict the amount of fuel evaporation given measured fuel droplet sizes and velocities, intake port and valve temperatures during warm up, and cylinder geometry.

Liquid fuel inflow into the cylinder is considered to be an important source of exhaust hydrocarbon (HC) emissions from automotive spark ignition engines. These liquid-fuel-caused emissions are increased significantly during the start up and subsequent warm-up period. This study analyzes the influence of several engine and injector design variables, and fuel parameters, on the in-cylinder liquid fuel behavior. The effect of the following parameters on the characteristics of the fuel droplets entering the cylinder was studied: Fuel volatility, injection timing, intake valve timing, injector type, spray geometry, and spray targeting in the intake port. A Phase Doppler Particle Analyzer (PDPA) was used in a single-cylinder flow visualization combustion engine to assess this in-cylinder liquid fuel behavior. Measurements of fuel droplet characteristics (size and velocity) were taken in selected locations in the vicinity of the intake valve during starting and warm up.