Refine Your Search

Date

Date

Topic

Topic

Technical review Optimization Corrosion Maintenance and Aftermarket Metals Technical Committee Parts Ground support

Search Results

Viewing 1 to 20 of 61
123Next >Last >>
Sort by published
Standard

Standard Sheet Steel Thickness and Tolerances
2024-03-04
CURRENT
J1058_202403
This SAE Recommended Practice provides an orderly series for designating the thickness of unocated and coated hot-rolled and cold-rolled sheet and strip. This document also provides methods for specifying thickness tolerances.
Standard

Hydrogen Embrittlement Testing of Ultra High Strength Steels and Stampings by Acid Immersion
2023-03-08
CURRENT
J3215_202303
This standard describes a test method for evaluating the susceptibility of uncoated cold rolled and hot rolled Ultra High Strength Steels (UHSS) to hydrogen embrittlement. The thickness range of materials that can be evaluated is limited by the ability to bend and strain the material to the specified stress level in this specification. Hydrogen embrittlement can occur with any steel with a tensile strength greater than or equal to 980 MPa. Some steel microstructures, especially those with retained austenite, may be susceptible at lower tensile strengths under certain conditions. The presence of available hydrogen, combined with high stress levels in a part manufactured from high strength steel, are necessary precursors for hydrogen embrittlement. Due to the specific conditions that need to be present for hydrogen embrittlement to occur, cracking in this test does not indicate that parts made from that material would crack in an automotive environment.
Standard

Sintered Powder Metal Parts: Ferrous
2018-08-24
CURRENT
J471_201808
Powder metal (P/M) parts are manufactured by pressing metal powders to the required shape in a precision die and sintering to produce metallurgical bonds between the particles, thus generating the appropriate mechanical properties. The shape and mechanical properties of the part may be subsequently modified by repressing or by conventional methods such. as machining and/or heat treating. While powder metallurgy embraces a number of fields wherein metal powders may be used as raw materials, this standard is concerned primarily with information relating to mechanical components and bearings produced from iron-base materials.
Standard

Magnetic Particle Inspection
2018-01-10
CURRENT
J420_201801
The scope of this SAE Information Report is to provide general information relative to the nature and use of magnetic particles for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of magnetic particle testing, and as a guide to more extensive references.
Standard

Surface Hardness Testing with Files
2018-01-10
CURRENT
J864_201801
Hardness testing with files consists essentially of cutting or abrading the surface of metal parts, and approximating the hardness by the feel, or extent to which, the file bites into the surface. The term "file hard" means that the surface hardness of the parts tested is such that a new file of proven hardness will not cut the surface of the material being tested.
Standard

Tool and Die Steels
2018-01-09
CURRENT
J438_201801
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

Chemical Compositions of SAE Wrought Stainless Steels
2018-01-09
CURRENT
J405_201801
The chemical composition of standard types of wrought stainless steels are listed in ASTM Specification A240. The UNS 20000 series designates nickel-chromium manganese, corrosion resistant types that are nonhardenable by thermal treatment. The UNS 30000 series are nickel-chromium, corrosion resistant steels, nonhardenable by thermal treatment. The UNS 40000 however, includes both a hardenable, martensitic chromium steel and nonhardenable, ferritic, chromium steel. Reference to SAE J412 is suggested for general information and usage of these types of materials. See Table 1.
Standard

Electroplate Requirements for Decorative Chromium Deposits on Zinc Base Materials Used for Exterior Ornamentation
2017-12-20
CURRENT
J1837_201712
This SAE Standard covers the physical and performance requirements for electrodeposited copper, nickel, and chromium deposits on exterior ornamentation fabricated from die cast zinc alloys (SAE J468 alloys 903 and 925), and wrought zinc strip (ASTM B 69). This type of coating is designed to provide a high degree of corrosion resistance for automotive, truck, marine, and farm usage where a bright, decorative finish is desired.
Standard

Sintered Tool Materials
2017-12-20
CURRENT
J1072_201712
This SAE Recommended Practice covers the identification and classification of ceramic, sintered carbide, and other cermet tool products. Its purpose is to provide a standard method for designating the characteristics and properties of sintered tool materials.
Standard

Valve Guide Information Report
2017-12-20
CURRENT
J1682_201712
This SAE Information Report provides: a Types of valve guides and their nomenclature b Valve guide alloy designations and their chemistries c Valve guide alloy metallurgy d Typical mechanical and physical properties of guide alloys e Typical dimensional tolerances of valve guides and their counterbores f Recommended interference fits g Installation procedures h Application considerations
Standard

Zinc Die Casting Alloys
2017-12-20
CURRENT
J469_201712
Because of the drastic chilling involved in die casting and the fact that the solid solubilities of both aluminum and copper in zinc change with temperature, these alloys are subject to some aging changes, one of which is a dimensional change. Both of the alloys undergo a slight shrinkage after casting, which at room temperature is about two-thirds complete in five weeks. It is possible to accelerate this shrinkage by a stabilizing anneal, after which no further changes occur. The recommended stabilizing anneal is 3 to 6 h at 100 °C (212 °F), or 5 to 10 h at 85 °C (185 °F), or 10 to 20 h at 70 °C (158 °F). The time in each case is measured from the time at which the castings reach the annealing temperature. The parts may be air cooled after annealing. Such a treatment will cause a shrinkage (0.0004 in per in) of about two-thirds of the total, and the remaining shrinkage will occur at room temperature during the subsequent few weeks.
Standard

Nondestructive Tests
2017-12-20
CURRENT
J358_201712
Nondestructive tests are those tests which detect factors related to the serviceability or quality of a part or material without limiting its usefulness. Material defects such as surface cracks, laps, pits, internal inclusions, bursts, shrink, seam, hot tears, and composition analysis can be detected. Sometimes their dimensions and exact location can be determined. Such tests can usually be made rapidly. Processing results such as hardness, case depth, wall thickness, ductility, decarburization, cracks, apparent tensile strength, grain size, and lack of weld penetration or fusion may be detectable and measurable. Service results such as corrosion and fatigue cracking may be detected and measured by nondestructive test methods. In many cases, imperfections can be automatically detected so that parts or materials can be classified.
Standard

Detection of Surface Imperfections In Ferrous Rods, Bars, Tubes, and Wires
2017-12-20
CURRENT
J349_201712
This SAE Information Report provides a summary of several methods that are available for detecting, and in some instances detecting and measuring, surface imperfections in rods, bars, tubes, and wires. References relating to detailed technical information and to specific applications are enumerated in 2.2.
Standard

Single Tooth Gear Bending Fatigue Test
2017-12-20
CURRENT
J1619_201712
This SAE Recommended Practice defines the set-up and procedure for conducting the SAE Single Tooth Bending Fatigue Test. The details of the test fixture to be used (referred henceforth as “the test fixture” in this document) and gear test sample and the procedures for testing and analyzing the data are presented in this document.
Standard

Selection of Zinc and Zinc-Alloy (Hot-Dipped and Electrodeposited) Coated Steel Sheet
2015-04-28
CURRENT
J1562_201504
Zinc and zinc-alloy coated steel is used to enhance a structure’s protection against corrosion degradation. For the purpose of this SAE Recommended Practice, a galvanized coating is defined as a zinc or zinc-alloy metallic coating. The selection of the optimum galvanized steel sheet product depends on many factors, the most important being: desired corrosion protection, formability, weldability, surface characteristics, and paintability. The trade-offs of these product characteristics are more complex than is the case with uncoated steel sheet products.
Standard

Standard Sheet Steel Thickness and Tolerances
2015-04-28
HISTORICAL
J1058_201504
This SAE Recommended Practice provides an orderly series for designating the thickness of unocated and coated hot-rolled and cold-rolled sheet and strip. This document also provides methods for specifying thickness tolerances.
Standard

High-Strength Carbon and Alloy Die Drawn Steels
2009-11-24
CURRENT
J935_200911
This SAE Recommended Practice is intended to provide basic information on properties and characteristics of high-strength carbon and alloy steels which have been subjected to special die drawing. This includes both cold drawing with heavier-than-normal drafts and die drawing at elevated temperatures.
123Next >Last >>
X