Search Results

A difficulty which exists when applying diagnostic techniques on large-scale diesel engines operating on the field, is that usually it is not possible to obtain measurement data at a wide engine operating range due to a number of constraints. In the present work is investigated the possibility to overcome this practical difficulty originating from the test procedure for engines operating on the field (i.e. marine or stationary applications). The main objective is to examine if a diagnosis procedure provides similar results when applied at various engine operating conditions. For this purpose an existing diagnostic technique, developed by the authors, is applied at different operating conditions on a large-scale two-stroke diesel engine used for power generation in a Greek island.

In this paper, the results are presented from the analysis of the second stage of an experimental investigation with the aim to provide insight to the cyclic, instantaneous heat transfer phenomena occurring in both the cylinder head and exhaust manifold wall surfaces of a direct injection (DI), air-cooled diesel engine. Results from the first stage of the investigation concerning steady-state engine operation have already been presented by the authors in this series. In this second stage, the mechanism of cyclic heat transfer was investigated during engine transient events, viz. after a sudden change in engine speed and/or load, both for the combustion chamber and exhaust manifold surfaces. The modified experimental installation allowed both long- and short-term signal types to be recorded on a common time reference base during the transient event.

During recent years, the deterioration of greenhouse phenomenon, in conjunction with the continuous increase of worldwide fleet of vehicles and crude oil prices, raised heightened concerns over both the improvement of vehicle mileage and the reduction of pollutant emissions. Diesel engines have the highest fuel economy and thus, highest CO2 reduction potential among all other thermal propulsion engines due to their superior thermal efficiency. However, particulate matter (PM) and nitrogen oxides (NOx) emissions from diesel engines are comparatively higher than those emitted from modern gasoline engines. Therefore, reduction of diesel emitted pollutants and especially, PM and NOx without increase of specific fuel consumption or let alone improvement of diesel fuel economy is a difficult problem, which requires immediate and drastic actions to be taken.

An experimental analysis is carried out to investigate several heat transfer characteristics during the engine cycle, in the combustion chamber and exhaust manifold walls of a direct injection (DI), air-cooled, diesel engine. For this purpose, a novel experimental installation has been developed, which separates the engine transient temperature signals into two groups, namely the long-and the short- term response ones, processing the respective signals in two independent data acquisition systems. Furthermore, a new pre-amplification unit for fast response thermocouples, appropriate heat flux sensors and an innovative, object-oriented, control code for fast data acquisition have been designed and applied. Experimentally obtained cylinder pressure diagrams together with semi-empirical equations for instantaneous heat transfer were used as basis for the calculation of overall heat transfer coefficient.

A major challenge for researchers and engineers in the field of diesel engine development is the simultaneous reduction of both NOx and soot emissions from diesel engines to comply with strict future emission legislation. One of the promising internal measures that focus on the reduction of soot emissions is post fuel injection which does not have a serious effect on NOx emissions. The main parameters involved when using this technique are post fuel quantity and dwell angle between the main and the post fuel injection events. In the present work a detailed computational investigation has been conducted to determine the effect of post fuel injection on engine performance and pollutant emissions (NOx and soot). To this scope, a phenomenological multi-zone combustion model has been used, properly modified to take into account the interaction of post and main injected fuel amounts.

Despite the improvement in HD Diesel engine out emissions future emission legislation requires significant reduction of both NOx and particulate matter. To accomplish this task various solutions exist involving both internal and external measures. As widely recognized, it will be possibly required to employ both types of measures to meet future emission limits. Towards this direction, it is necessary to reduce NOx further using internal measures. Several solutions exist in that area, but the most feasible ones according to the present status of technical knowledge are EGR, water injection or fuel/water emulsions. These technologies aim to the reduction of both the gas temperature and oxygen concentration inside the combustion chamber that strongly affect NOx formation. However, there remain open points mainly concerning the effectiveness of water addition techniques and penalties related to bsfc and soot emissions.

The modeling of transient turbocharged diesel engine operation appeared in the early seventies and continues to be in the focal point of research, due to the importance of transient response in the everyday operating conditions of engines. The majority of research has focused so far on issues concerning thermodynamic modeling, as these directly affect heat release predictions and consequently performance and pollutants emissions. On the other hand, issues concerning the dynamics of transient operation are often disregarded or over-simplified, possibly for the sake of speeding up program execution time. In the present work, an experimentally validated transient diesel engine simulation code is used to study and evaluate the importance of such dynamic issues. First of all, the development of various forces (piston, connecting rod, crank and main crankshaft bearings) is computed and illustrated in order to evaluate the importance of abrupt load increases on the bearings durability.

Considering future emission legislation for HD diesel engines it is apparent that it will be probably necessary to employ A/T devices to achieve them. The main problem concerns the simultaneous control of both NOx and particulate emissions at an acceptable fuel penalty. Concerning particulate matter the use of particulate traps is considered to be a proven technology while for NOx emission control; various solutions exist mainly being the use of SCR catalysts or LNT devices. But LNT traps require periodical regeneration, which is accomplished by generating reducing agents i.e. CO and H2. The present investigation focuses on the regeneration of LNT devices through the engine operating cycle. This can be achieved using two techniques, additional injection of fuel at the exhaust manifold (external measures) or operation at low lambda values in the range of 1.0 or lower (internal measures).

In the present work a sensitivity analysis is conducted using a multi-zone phenomenological model developed in the past by the author's, to estimate the effect of model's constants on engine performance and emissions. The constants used for this analysis are those embedded in the semi-empirical relations of the model, regarding air entrainment rate, combustion rate, ignition delay and evaporation rate. The model is applied on a heavy duty supercharged DI diesel engine and the effect of each of these constants on measurable engine parameters is defined. From the sensitivity analysis the relation between model constants and engine output data is derived. These results are used to define a constants determination procedure. The target is to define a limited number of adjustable constants so that the procedure can be of practical use. Following this, the calibration procedure is applied to determine the value of each constant, at various engine speeds and loads for the engine in question.

During the last years a great effort has been made by many NATO nations to move towards the use of one military fuel for all the land-based military aircraft, vehicles and equipment employed on the military arena. This idea is known to as the Single Fuel Concept (SFC). The fuel selected for the idea of SFC is the JP-8 (F-34) military aviation fuel which is based upon the civil jet fuel F-35 (Jet A-1) with the inclusion of military additives possessing anti-icing and lubricating properties. An extended experimental investigation has been conducted in the laboratory of Thermodynamic and Propulsion Systems at the Hellenic Air Force Academy. This investigation was conducted with the collaboration of the respective laboratories of National Technical University of Athens and Hellenic Naval Academy as well.

Worldwide demand for reduction of automotive fuel consumption and carbon dioxide emissions results in the introduction of new diesel engine technologies. A promising technique for increasing the power density of reciprocating engines, improving fuel economy and curtailing engine exhaust emissions is the use of variable compression ratio (VCR) technology. Several automotive manufacturers have developed prototype vehicles equipped with VCR gasoline engines. The constructive pattern followed to alter the compression ratio varies with the manufacturer. The implementation of VCR technology offers two main advantages: the reduction of CO2 emissions due to optimal combustion efficiency in the entire range of engine operating conditions and the increase of power concentration due to high boosting of a small engine displacement (i.e., engine downsizing).

Diesel engine manufacturers are currently intensifying their efforts to meet future emission limits that require a drastic reduction of NOx and particulate matter compared to present values. Even though several after-treatment techniques have been developed for tailpipe NOx reduction in heavy duty diesel engines, the in-cylinder control of NOx formation still remains of utmost importance. Various methods have been used to control NOx formation in diesel engines such as retarded injection timing and EGR providing each one of them very promising results. However, use of these techniques is accompanied by penalties in specific fuel consumption and exhaust soot. A promising technology for NOx reduction especially for heavy-duty diesel engines and mainly large scale ones is the addition of water to the combustion chamber to reduce peak combustion temperature that obviously affects NOx formation.

Study and modeling of transient operation is an important scientific objective. This is due to the fact that the majority of daily vehicle driving conditions involve transient operation, with non-linear situations experienced during engine transients. Thus, proper interconnection is needed between engine, governor, fuel pump, turbocharger and load. This paper surveys the publications available in the open literature concerning diesel engine simulations under transient operating conditions. Only those models that include both full engine thermodynamic calculations and dynamic powertrain modeling are taken into account, excluding those that focus on control design and optimization. Most of the attention is concentrated to the simulations that follow the filling and emptying modeling approach. A historical overview is given covering, in more detail, research groups with continuous and consistent study of transient operation.

A heat release analysis of experimental pressure diagrams, appropriate for indirect injection (divided chamber) diesel engines, is developed and used to obtain heat release rate profiles during the combustion process in each combustion chamber. Attention is paid to the correct processing of the data, due to the inherent complexity of the mass interchange between the two combustion chambers. The analysis concerns a turbocharged, indirect injection diesel engine, having a very small pre-chamber and a very narrow connecting passageway, operated at various load and speed conditions, located at the authors' laboratory. An extended experimental work, at steady-state conditions, is conducted on a specially developed test bed configuration of this engine, which is connected to a high-speed data acquisition and processing system.

A second-law analysis is performed in both chambers of an indirect injection turbocharged diesel engine and the simulation program developed is used to study the second-law performance of the engine at various operating conditions, steady state and transient. The simulation developed is based on the filling and emptying approach and provides detailed analysis of thermodynamic, dynamic and second-law differential equations on a degree crank angle basis. It incorporates a detailed mathematical simulation of the fuel pump and solves each equation separately for each one of the six cylinders of the engine in hand. The model is validated against experimental data at steady state and transient conditions, obtained at the authors' laboratory. The prechamber rate and cumulative availability terms and irreversibilities are computed and depicted against the main chamber ones during the 720 degrees crank angle of an engine cycle.

The model has already been applied on an old technology, naturally aspirated HSDI Diesel engine and on a heavy-duty turbocharged DI one equipped with a high pressure PLN fuel injection system, and the results were satisfying as far as performance and pollutant emissions (Soot and NO) are concerned. Taking into account that the main scope of engine simulation models is to assist engineers and researchers to understand the complex mechanisms involved in diesel engine combustion and pollutants formation and that through the continues engine development, new techniques are implemented, it is obvious that engine simulation models must always be enhanced with new features in order to be kept up-to-date. In this study the model has been modified to take into account the effect of EGR, since the latter one is a measure that will be used more extensively in the future to control NO emissions from turbocharged HDDI Diesel engines.

With the increasing public interest in energy supply and the environment, attention has focused on the development of ecological and efficient combustion technologies. One of these technologies could be the use of natural gas as supplement fuel for diesel fuel in DI diesel engines. The great availability at attractive prices and the clean nature of combustion are the most important advantages of natural gas compared to conventional diesel fuel. In the present work are given theoretical and experimental results for the combustion mechanism of natural gas in a compression ignition environment, with special emphasis on the combined heat release rate of natural gas and diesel fuel, the duration of combustion and the ignition delay period. Results are also provided for the formation history of pollutants inside the combustion chamber of a DI diesel engine operating in dual fuel mode (with natural gas fuelling).

A major challenge in the development of future heavy-duty diesel engines is the reduction of NOx and particulate emissions with minimum penalties in fuel consumption. The further decrease of emission limits (i.e., EPA 2007-2010, Euro 5 and Japan 05) requires new, advanced approaches. The injection system of DI diesel engines has an important role regarding the fulfillment of demands for low pollutant emissions and high engine efficiency. One of the injection system parameters affecting fuel spray characteristics, fuel-air mixing and consequently, combustion and pollutant formation is the geometry of the nozzle hole. A detailed experimental investigation was conducted at UPV-CMT using three different nozzle hole types: a standard, a convergent and a divergent one to discern the effect of nozzle hole conical shape on engine performance and emissions.

The diesel engine is currently the most efficient powertrain for vehicle propulsion. Unfortunately it suffers from rather high particulate and NOx emissions that are directly related to its combustion mechanism. Future emission legislation requires drastic reduction of NOx and particulate matter compared to present values. Engine manufacturers in their effort to meet these limits propose two solutions: reduction of pollutants inside the combustion chamber using internal measures and reduction at the tailpipe using aftertreatment technology. Currently there are various opinions considering the final solution. Taking into account information related to aftertreatment technology, an effort should be made to reduce pollutants inside the combustion chamber as much as possible. The last is obvious if we account for the even more strict emission limits to be applied after 2010 that will require a combination of aftertreatment and internal measures.

The transient operation of turbocharged diesel engines during turbocharger compressor surging is investigated through simulation. This form of compressor dynamic instability can generate large amplitude compressor mass flow and pressure rise oscillations, sometimes leading even to flow reversals, and may also induce severe torsional loading to the turbocharger shaft. A model predicting the dynamic behavior of the engine air-charging system when compressor surging occurs was developed in conjunction with a linearized quasi-steady diesel engine simulation code. This analysis possesses the advantage over the more detailed engine codes of basic simplicity, speed of calculation and no need of many engine and turbocharger components parameters given as input data. Emphasis is given to the correct modeling of the physics of the phenomena concerned. Transient operation runs, including critical cases for surging initiation, were applied for two similar six-cylinder diesel engines.