Refine Your Search

Date

Date

Topic

Topic

Vehicle drivers Identification Analysis methodologies Insulation Vehicle occupants AMS CE Elastomers Committee

Search Results

Viewing 1 to 20 of 559
123Next >Last >>
Sort by published
Standard

Identification and Packaging Elastomeric Products
2024-03-04
CURRENT
AMS2810J
This specification provides requirements for the identification and packaging of sheet, strip, extrusions, and molded parts made of natural rubber, synthetic rubber, reclaimed rubber, and combinations of the above with other materials such as asbestos, cork, and fabrics. AMS2817 covers preferred requirements for identification and packaging of preformed packings.
Standard

Elastomer: Fluorosilicone Rubber (FVMQ), Fuel and Oil Resistant, High Strength, 45 – 55 Shore A Hardness, For Products in Fuel Systems / Lubricating Oils
2023-10-16
CURRENT
AMS3329D
This specification covers a high strength fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-ring cord, and molded in place gaskets for aeronautical and aerospace applications.
Standard

Elastomer: Chloroprene Rubber (CR) Weather Resistant 55 - 65
2022-06-13
CURRENT
AMS3241K
This specification covers a chloroprene (CR) rubber that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes such as window channels, bumper pads, chafing strips, etc. For molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the equivalent AMS7XXX specification.
Standard

Elastomer: Chloroprene Rubber (CR) Weather Resistant 35 - 45
2022-06-13
CURRENT
AMS3240L
This specification covers a chloroprene rubber (CR) that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes such as window channels, bumper pads, chafing strips, etc. For molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the equivalent AMS7XXX specification.
Standard

Packaging and Identification of Molded Elastomeric Seals and Sealing Components
2022-05-20
CURRENT
AMS2817G
This specification covers procedures which will provide protection of elastomeric seals and seal assemblies such as O-rings, cap seal assemblies, and other designs from contamination by foreign materials and handling / transportation / storage damage prior to installation and ensure positive identification by part number of each piece until it is installed.
Standard

Sponge, Chloroprene (CR) Rubber, Soft
2022-03-01
CURRENT
AMS3197N
This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered.
Standard

Rubber, Ethylene-Propylene, Hydrazine Resistant
2021-07-21
WIP
AMSR83412B
This specification covers three types of rubber having good resistance to high and low temperature and hydrazine type propellants, but poor resistance to hydrocarbon oils or solvents. Hydrazines are hazardous chemicals. See Dangerous Properties of Industrial Materials; by N. Irving Sax.
Standard

Rubber: Vinyl-Methyl Silicone (VMQ) Hot Air Resistant Low Compression Set, 70 to 80 Type A Hardness for Seals in Hot Air Systems
2021-05-19
CURRENT
AMS7267H
This specification covers a silicone (VMQ) rubber in the form of molded rings. These rings have been used typically as sealing rings for service from -65 to +260 °C (-85 to +500 °F) in contact with air, but usage is not limited to such applications. The cross-section of such rings is usually not over 0.275 inch (6.98 mm) in diameter or thickness.
Standard

Elastomer: Methyl/Methyl Vinyl Silicone, (MQ/MVQ) High Temperature/Gas Turbine Engine Oil/Phosphate Esther Hydraulic Fluid Resistant High Strength/High Tear/High Modulus 55 to 65 Type “A” Hardness For Products in High Temperature Environments/Gas Turbine Engine Oils
2019-11-26
CURRENT
AMS3306D
This specification covers a methyl or methyl vinyl silicone rubber material that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
Standard

Static Seal Test Fixture and Procedure
2019-11-05
CURRENT
AS7982
This SAE Aerospace Standard (AS) provides dimensions and procedures for a standardized test fixture used to evaluate the static performance of O-rings and other seal types in glands per AS4716 and AS5857.
123Next >Last >>
X