Search Results

To improve the energy absorption capacity of front-end structures during a vehicle crash, a novel 12-sided cross-section was developed and tested. Computer-aided engineering (CAE) studies showed superior axial crash performance of the 12-sided component over more conventional cross-sections. When produced from advanced high strength steels (AHSS), the 12-sided cross-section offers opportunities for significant mass-savings for crash energy absorbing components such as front or rear rails and crush tips. In this study, physical crash tests and CAE modeling were conducted on tapered 12-sided samples fabricated from AHSS. The effects of crash trigger holes, different steel grades and bake hardening on crash behavior were examined. Crash sensitivity was also studied by using two different part fabrication methods and two crash test methods. The 12-sided components showed regular folding mode and excellent energy absorption capacity in axial crash tests.

The objective of this paper focused on the modeling of an adaptive energy absorbing steering column which is the first phase of a study to develop a modeling methodology for an advanced steering wheel and column assembly. Early steering column designs often consisted of a simple long steel rod connecting the steering wheel to the steering gear box. In frontal collisions, a single-piece design steering column would often be displaced toward the driver as a result of front-end crush. Over time, engineers recognized the need to reduce the chance that a steering column would be displaced toward the driver in a frontal crash. As a result, collapsible, detachable, and other energy absorbing steering columns emerged as safer steering column designs. The safety-enhanced construction of the steering columns, whether collapsible, detachable, or other types, absorb rather than transfer frontal impact energy.

This paper presents the final phase of a study to develop the modeling methodology for an advanced steering assembly with a safety-enhanced steering wheel and an adaptive energy absorbing steering column. For passenger cars built before the 1960s, the steering column was designed to control vehicle direction with a simple rigid rod. In severe frontal crashes, this type of design would often be displaced rearward toward the driver due to front-end crush of the vehicle. Consequently, collapsible, detachable, and other energy absorbing steering columns emerged to address this type of kinematics. These safety-enhanced steering columns allow frontal impact energy to be absorbed by collapsing or breaking the steering columns, thus reducing the potential for rearward column movement in severe crashes. Recently, more advanced steering column designs have been developed that can adapt to different crash conditions including crash severity, occupant mass/size, seat position, and seatbelt usage.

A highly controlled six-vehicle crash test program was conducted to provide an estimate of the test-to-test variability of the NHTSA-proposed passenger car dynamic side impact test procedure. The results of this program showed that the rear seat test dummy response measurements are especially sensitive to various parameters of the test procedure. This paper provides estimates of front and rear seated SID dummy response measurement variability in four-door, 1990 Ford Taurus vehicles. Conclusions and recommendations from this controlled crash test program are made to provide guidance to help reduce the test-to-test variability of the test dummy responses.

The development of combined finite element and spring / rigid mass crash simulation dummy models for automotive applications is described. In order to better understand the crash phenomena and occupant kinematics during vehicle crashes, recent developments have been focused on the use of finite element techniques in the simulation of both structure and structure / dummy interactions. The combination of spring /rigid mass modeling and finite element technique is used to develop models of fiftieth percentile Hybrid III and Side impact Dummies in a finite element program (RADIOSS). In general, the dummies are modeled with rigid masses and joints with techniques similar to those used in Crash Victim Simulation programs like MADYMO and CAL3D. Only selected components, like the Hybrid III dummy thorax and the SID pelvis and jacket, are modeled with finite element shell and brick elements to improve dummy / restraint system and dummy / structure interaction responses.

The modeling of plastic fuel tank systems for crash safety applications has been very challenging. The major challenges include the prediction of fuel sloshing in high speed impact conditions, the modeling of multilayer thermoplastic fuel tanks with post-forming (non-uniform) material properties, and the modeling of tank straps with pre-tensions. Extensive studies can be found in the literature to improve the prediction of fuel sloshing. However, little research had been conducted to model the post-forming fuel tank and to address the tension between the fuel tank and the tank straps for crash safety simulations. Hoping to help improve the modeling of fuel systems, the authors made the first attempt to tackle these major challenges all at once in this study by dividing the modeling of the fuel tank into eight stages. An ALE (Arbitrary Lagrangian-Eulerian) method was adopted to simulate the interaction between the fuel and the tank.

Reliable testing of a mechanical system requires the procedures used for the evaluation to be repeatable and reproducible. However, it is never possible to exactly repeat or reproduce the tests that are used for evaluation. To overcome this limitation, a statistical evaluation procedure can generally be used. However, most of the statistical procedures use scalar values as input without the ability to handle vectors or time-histories. To overcome these limitations, two numerical/statistical methods for determining if the impact time-history response of a mechanical system is repeatable or reproducible are evaluated and elaborated upon. Such a system could be a vehicle, a biological human surrogate, an Anthropometric Test Device (ATD or dummy), etc. The responses could be sets of time-histories of accelerations, forces, moments, etc., of a component or of the system. The example system evaluated is the BioRID II rear impact dummy.

Increasing electronics content, growing computing power, and proliferation of opportunities for information connectivity (through improved sensors, GPS, road and traffic information systems, wireless internet access, vehicle-to-vehicle communication, etc.) are technology trends which can significantly transform and impact future automotive vehicle's control and diagnostic strategies. One aspect of the increasing vehicle connectivity is access to ambient and road condition information, such as ambient temperature, ambient pressure, humidity, % cloudiness, visibility, cloud ceiling, precipitation, rain droplet size, wind speed, and wind direction based on wireless internet access. The paper discusses the potential opportunities made available through wireless communication between the vehicle and the internet.

Ten sled tests were conducted with a Hybrid III 10-year-old dummy under a 3-point belt only restraint condition to evaluate its performance. The results of the Hybrid III 10-year-old in these tests indicate that there are artifactural noise spikes observable in the transducer responses. A number of metal-to-metal contacts in the shoulder area were identified as one of the sources for the chest acceleration spikes. Noise spikes were also observed in the response from multiple body regions; however, the source of the spikes could not be determined. Compared to the other Hybrid III dummies, non-characteristic dummy chest deflection responses were also observed. This limited analysis indicates that the Hybrid III 10-year-old dummy requires additional development work to eliminate the metal-to-metal contacts in the shoulder area and to understand and correct the other sources of the noise spikes. More investigation is needed to determine if the chest deflection response is appropriate.

The thermal comfort of passengers within a vehicle is often the main objective for the climate control engineer; however, the need to maintain adequate visibility through the front and side windows of a vehicle is a critical aspect of safe driving. This paper compares the performance of the side window defrosting and demisting mechanism of several current model vehicles. The study highlights the drawbacks of current designs and points the way to improved passive defrosting mechanisms. The investigation is experimental and computational. The experiments are carried out using full-scale current vehicle models. The computational study, which is validated by the experiments, is used to perform parametric investigation into the side window defrosters performance. The results show that the current designs of the side-defroster nozzles give maximum airflow rates in the vicinity of the lower part of the window, which yields unsatisfactory visibility.

Drive shaft modelling effects frontal crash finite element simulation. A 35 mph rigid barrier impact of a body on frame SUV with an one piece drive shaft and a unibody SUV with a two piece drive shaft have been studied and simulated using finite element analyses. In the model, the drive shaft can take significant load in frontal impact crash. Assumptions regarding the drive shaft model can change the predicted engine motion in the simulation. This change influences the rocker @ B-pillar deceleration. Two modelling methods have been investigated in this study considering both joint mechanisms and material failure in dynamic impact. Model parameters for joint behavior and failure should be determined from vehicle design information and component testing. A body on frame SUV FEA model has been used to validate the drive shaft modeling technique by comparing the simulation results with crash test data.

This paper discusses steps for identifying, evaluating and recommending a quantifiable design metric or metrics for Side Airbag (SAB) development. Three functionally related and desirable attributes of a SAB are assumed at the onset, namely, effective SAB coverage, load distribution and efficient energy management at a controlled force level. The third attribute however contradicts the “banana shaped” force-displacement response that characterizes the ineffective energy management reality of most production SAB. In this study, an estimated ATD to SAB interaction energy is used to size and recommend desired force-deformation characteristic of a robust energy management SAB. The study was conducted in the following three phases and corresponding objectives: Phase 1 is a SAB assessment metric identification and estimation, using a uniform block attached to a horizontal impact machine.

The potential effects of passenger air bag deployment on an out-of-position three-year-old child dummy and on a three-year-old child dummy in a child restraint system are two of the items considered in the development of an automotive passenger air bag restraint system. In order to increase our understanding of the passenger air bag and three-year-old dummy interaction, we have developed a three dimensional computer model of a three-year-old child dummy. The dummy model has a compressible sternum and a multi-segment representation of the neck which helps improve the predictive capabilities of the neck criteria. The dummy properties needed as inputs to the occupant model were all experimentally determined. An energy technique was used for separating the elastic, damping and friction components for each joint. Three HYGE sled test cases were simulated to validate the model.

The viscous criterion (V*C) has been proposed by biomechanics researchers as a generic biomechanical index for potential soft tissue injury. It is defined by the product of the velocity of deformation and the instantaneous compression of torso and abdomen. This criterion requires calculation and differentiation of measured torso/abdomen compression data. Various computational algorithms for calculating viscous criterion are reviewed and evaluated in this paper. These include methods developed by Wayne State University (WSU), NHTSA (DOT) and Ford. An evaluation has been conducted considering the accuracy of these algorithms with both theoretical and experimental data from dummy rib compressions obtained during a crash test. Based on these results, it is found that: V*C results depend on the scheme used in the computation process, the sampling rate and filtering of original raw data. The NHTSA method yields the lowest V*C value.

Numerical simulation techniques are commonly used to assess the crash performance of automobiles and guide their design during the development stage. Mathematical models of vehicle structures, restraint systems and dummies are developed and verified under different test conditions to ensure an effective usage during their application in the study of a crash situation. This paper describes the development and validation of a finite element model of the US Department of Transportation (DOT) side impact dummy (SID). The geometry of the dummy parts is represented by shell and solid elements created from a digital scan of the dummy and the material properties are derived from quasi-static tests of each component. Springs and rigid bodies are added to represent the shock absorber and certain rigid parts such as the femur and ilium. The model verification is carried out by subjecting the dummy to twenty four impact conditions and comparing the simulations to test results.

Biomechanically-based test surrogates are a valuable tool when used to evaluate side impact protection strategies, particularly when their responses are understood relative to dummy injury reference values. Test surrogates such as the BIOSID and EUROSID-1 side impact dummies have anatomically located pelvic load cells to help describe in varying degrees the pelvic load paths and help indicate the potential for pelvic injury. From a rigid body analysis, it was determined that the BIOSID pelvic structure can be separated into two rigid bodies due to load cell placement. A new configuration for the sacrum load cell is proposed for the BIOSID pelvis. Hammer impact tests were conducted on the BIOSID pelvis. The tests identified the load paths through the pelvis and indicated the relationship between the load cells. From rigid wall sled tests, the pelvis load cells were summed to identify the applied total external load.

The influence of calcium treatment on the mechanical properties of a plain carbon steel (SAE 1050) was investigated. The mechanical properties investigated were tensile and impact strength, fatigue crack growth rate, and the fatigue threshold. Impact testing was conducted at both room temperature and at -40°C. Several heats of both calcium and non-calcium treated steel (SAE 1050) were tested in both the as hot-rolled condition and in the quenched and tempered condition (with a hardness level of HRC = 45). The results of this investigation show no significant difference in the tensile properties or room temperature impact properties between the calcium treated and the non-calcium treated steels. However, the impact strengths of calcium treated steels were slightly higher than that of non-calcium treated steels at -40°C.

This paper describes how polar plots are constructed and used to evaluate fields of view from vehicles. A polar plot presents a driver's three dimensional view of the vehicle structure, such as the window openings or mirrors, and the objects outside of the vehicle, such as other vehicles in adjacent lanes, in a two dimensional angular (or polar) field. These plots are simple and effective in understanding and visualizing complex visibility problems. Since the plot is made in angular space, a Human Factors Engineer can use the plots for direct assessment of drivers' visual problems, such as sizes of monocular and binocular obscurations. Location of visual targets in the driver's peripheral vision, and magnitude of eye and head turn angles, can be easily determined by measuring coordinates of details shown in a polar plot.

The SAE Large Male and Small Female Dummy Task Group has recommended a change to the Hybrid III dummy hip joint. This change was made because of a non-biofidelic interference in the current design that can influence chest accelerations. The modifications include a new femur casting shaft design and the addition of an elastomeric stop to the top of the casting. Static testing and Hyge sled tests were done to evaluate the modifications. Based on the results, the new design satisfied the requirements set by the SAE task group and reduced the influence of hip joint characteristics on chest accelerations.

This paper describes the development of a Dynamic Door Component Test Methodology (DDCTM) for side impact simulation. A feasibility study of the methodology was conducted using a MADYMO computer model by taking parameters such as door pre-crush, door-to-SID (Side Impact Dummy) contact velocity and the deceleration profile into consideration. The prove-out tests of this methodology was carried out on a dynamic sled test facility. The DDCTM has been validated for various carlines. In addition, various existing dynamic component test methods are reviewed. In our approach, a pre-crushed door, mounted on a sled, strikes a stationary SID at a pre-determined velocity. A programmable hydraulic decelerator is used to decelerate the sled to simulate the barrier/door deceleration pulse during door-to-SID contact period. This test procedure provides excellent correlation of the SID responses between the component test and the full-scale vehicle test.