Search Results

Due to high energy demand and limited availability of fossil fuels, the energy necessity becomes a point of apprehension as it results in hike of fuel prices. It is essential to develop renewable energy resources while considering the impact on environment. In the last decade, demand of alternative fuels has increased a lot. Therefore, researchers have already started working on the aim of developing a green fuel to overcome the future energy demand. And as we know that the biodiesel is generally prepared from the non-edible and renewable resources thus, it can be among the competitive alternative future fuels. Besides that, it does not require any prior engine modifications for its usual advantage among other alternative fuels while using it within certain boundaries. However, the process biodiesel production is in itself time consuming which increases the cost of production while decreasing the yield.

Worldwide, research is going on numerous types of engines that practice green and alternative energy such as natural gas engines, hydrogen engines, and electric engines. One of the possible alternatives is the air powered car. Air is abundantly available and can be effortlessly compressed to higher pressure at a very low cost. After the successful development of Compressed Air Engines, engineers shifted their focus in making this technology cost effective and feasible. This led to advancement in the field of pneumatics that is advanced Compressed Air Engine Kit (used for conversion of a small-two stroke SI engine to Compressed Air Engine) where its frugality and compatibility is kept at high priority. This research is in continuation with our previous project of development of an advanced Compressed Air Engine kit and optimisation of injection angle and injector nozzle area for maximum performance.

The automotive underbody diffuser is an expansion device which works by speeding up the air flowing underneath a vehicle. This reduces the pressure below the vehicle thereby increasing downforce. When designed properly, it can lead to a massive gain in downforce and even a reduction in drag. However, a majority of the research and development is restricted to motorsport teams and supercar manufacturers and is highly secretive. Most of the publicly available research has been done for very simple shapes (bluff bodies) to study the effects of ground clearance and rake angle. Very little research has been done for complex geometries with vanes, flaps and vortex generators. This paper aims to investigate the effects of the addition of vanes/strakes and flaps, their location as well as angle, on diffuser performance. Computational Fluid Dynamics simulations have been carried out using three dimensional, steady state RANS equations with the k-ε turbulence model on STAR CCM+ V9.06.

The increment in the application of fossil fuels is leading the world into a catastrophic state both environmentally and economically. Current demand for fuels exceeds its imminent supply and rather sooner than later energy demands will have to shift towards non-conventional fuels to cope with the situation. With constant developments in the automotive sector, several solutions have been found but none have been as good as gasoline to substitute it in the commercial market. One such solution being compressed air might solve this global fuel crisis, which serves a glowing advantage of being cheaper and greener as it produces zero tail-pipe emissions, and can help in decreasing automobile’s contribution to global warming. Though the potential energy stored in the compressed air limits its application to light duty vehicles and still there will be a need for other alternative solutions for the heavy duty vehicles in order to relieve the pressure from the fossil fuels.

Exploring and enhancement of biodiesel production from feedstock like non-edible vegetable oil is one of the powerful method to resolve inadequate amount of conventional raw materials and their high prices. The main aim of this study is to optimize the biodiesel production process parameters of a biodiesel obtained from non-edible feedstocks, namely Neem (Azadirachta indica) oil and Sesame (Sesamum indicum L.) oil, with response surface methodology using Doehlert’s experimental design. Based on the results, the optimum operating parameters for transesterification of the mixture A50S50 oil mixture at 51.045° C over a period of 45 minutes are as follows: methanol-to-oil ratio: 8.45, and catalyst concentration: 1.933 wt.%. These optimum operating parameters give the highest yield for the A50S50 biodiesel with a value of 95.24%.

As petroleum prices are rising continuously biodiesel production has been receiving worldwide awareness. Thus for its production the requirement for non-edible and unidentified feedstocks has risen. This research presents the production and process optimization of biodiesel obtained from non-edible feedstock namely cedar wood(Cedrus deodara) oil, with response surface methodology using statistical software minitab 18.0. Cedar Wood (Cedrus deodara) is a tree accessible in different parts of the world like India and Nepal. In Indian context, these are available in abundance especially in the forests of Himalayan region as a non-edible feedstock. Methyl ester of Cedar Wood Oil is prepared by process known as Transesterification. The FFA content of cedar wood oil was 0.5% which is below the 2% suggested for the application of the one step alkaline transesterification method.

Study of starting friction during the running of the engineering application has an important role in designing them, especially working at low speed and high load conditions. A significant portion of research and development today is concentrated on saving the energy by reducing the friction. The present paper addresses the measurement technique and analysis of the starting friction during the running of the journal bearing. The experiments were performed during the hydrodynamic lubrication regime using SAE 15W-30 lubricating oil. A journal bearing having journal diameter as 22 mm, length/diameter ratio 1 and 0.027 mm radial clearance has been designed and fabricated to test the starting friction. Analysis of starting friction and average friction torque during the running of journal bearing was done at 900, 1150, 1400, 1650, 1900, 2150 and 2400 revolution per minute (rpm) speed of the journal at load values of 250, 400 and 500 N.

Metal matrix composites have a large range of applications in the automobile industry due to its characteristics and properties. Al-based MMC have aluminum as matrix metal that has properties which are well concerned with the automobile industry. Some of these properties are high strength to weight ratio and lightweight. In this paper we are trying to develop aluminum-based metal matrix composite (MMC) reinforced with natural fibers ashes, we are using fine ashes of Sugarcane (bagasse), Groundnut Shell Ash (GSA), Rice Husk Ash (RHA) and Coconut shell (Jute) ash, different effects are investigated for different percentage of reinforcing material which is being produced by burning in a free atmosphere. Ball milling is used for making fine particle size of different natural fibers ash. Nine samples were made by the stir casting process consisting of Al6063 as base metal and different concentration of reinforcement.

Additive manufacturing has experienced rapid growth over a span of 25 years. Additive manufacturing involves the development of a three-dimensional (3D) object by stacking layer upon layer. Conventional machining techniques involve the removal of material. However, this technique differentiates itself from other techniques by means of addition of the material. The integration of CAD with additive manufacturing has offered the ability to create complex structures. Despite its clear benefits, additive manufacturing suffers from a high initial investment. An average cost of an entry level commercial 3D printer is 600$. A low-cost 3D printer has been designed and built for experimental investigation within a budget of 300$. The paramount process of 3D printing involves a combination of interpreting data from CAD files and controlling the motors using this data. The various design considerations while developing the 3D printer have been discussed.

The art and science of thrust vectoring technology has seen a gradual shift towards fluidic thrust vectoring techniques owing to the potential they have to greatly influence the aircraft propulsion systems. The prime motive of developing a fluidic thrust vectoring system has been to reduce the weight of the mechanical thrust vectoring system and to further simplify the configuration. Aircrafts using vectored thrust rely to a lesser extent on aerodynamic control surfaces such as ailerons or elevator to perform various maneuvers and turns than conventional-engine aircrafts and thus have a greater advantage in combat situations. Fluidic thrust vectoring systems manipulate the primary exhaust flow with a secondary air stream which is typically bled from the engine compressor or fan. This causes the compressor operating curve to shift from the optimum condition, allowing the optimization of engine performance. These systems make both pitch and yaw vectoring possible.

Increased demand and use of fossil fuels in transportation sector accompanied by the global oil crisis does not support sustainable development for the future generations to come. Not only that, today's on-road vehicles produce over one third of the CO and NOX present in our atmosphere and over twenty per cent of the global warming pollution. This air pollution carries significant risks for human health and the environment. Through clean vehicle and fuel technologies, it is possible to significantly reduce air pollution from our vehicles. In such a grim situation, Compressed Air Vehicles (CAV) powered by pressurized air stored in high pressure storage tanks seem to be one of the practical solutions available for tackling the fuel crisis and environment related issues.

The functions of a piston ring are to seal off the combustion pressure, to distribute and control the oil, to transfer heat and to stabilize the piston. Most piston rings and metallic sealing rings for modern application where running conditions are severe, require some form of coating to minimise abrasion and corrosion. The piston ring coating improves the life of engine as well as fuel efficiency. In this study, physical vapour deposition (ion chrome plating) was investigated; plates with similar composition as the piston ring material were prepared by the casting process using induction arc furnace and sand mould. Wear test of the coating was conducted on pin on disc machine under dry conditions. The wear rate was calculated using mass loss methods on an electronic balance having least count of 1× 10−4 g.

Biodiesel is a potential substitute for diesel and extensive research is carried in India on production and utilization of biodiesel from a variety of edible/non-edible, animal fat and waste oils. However, issues like stability, clogging, increased NOx, and high consumption rate etc. are some of the critical issues which are associated with long-term use of these alternative fuels in a diesel engine. The recent developments in science and technology may have concreted a method to create nano measure vigorous resources that have incredible benefits to micron sized constituents. Nano liquids may be a fresh period of compact-fluid complex constituents comprising of nano sized concrete elements disseminated into a base liquid. The present study investigates the effect of doping metal oxides nanoparticles with waste fish oil-based biodiesel. For the present study, the blends of fuel are prepared by using 30ppm each of titanium dioxide and alumina nanoparticles respectively.

Flow separation is one of the primary causes of increase in form drag in vehicles. This phenomenon is also visible in the case of lightweight vehicles moving at high speed, which greatly affects their aerodynamics. Spherical depressions maybe used to delay the flow separation and decrease drag in such vehicles. This study aims for optimization of aspect ratio (AR) of spherical depressions on hatchback cars. Spherical depressions were created on the bonnet of a generalized light vehicle Computer-Aided Design (CAD) model. The diameter of each spherical depression was set constant at 60 mm, and the center-to-center distance between consecutive spherical depressions is fixed at 90 mm. The AR of spherical depressions was taken as the parameter that was varied in each model. ARs 2, 4, 6, and 8 were considered for the current investigation. Three-dimensional (3D) CFD analyses were then performed on each of these models using a validated computational model.

The danger posed by climate change and the striving for securities of energy supply are issues high on the political agenda these days. Governments are putting strategic plans in motion to decrease primary energy use, take carbon out of fuels and facilitate modal shifts. Man's energy requirements are touching astronomical heights. The natural resources of the Earth can no longer cope with it as their rate of consumption far outruns their rate of regeneration. The automotive sector is without a doubt a chief contributor to this mayhem as fossil fuel resources are fast depleting. The harmful emissions from vehicles using these fuels are destroying our forests and contaminating our water bodies and even the air that we breathe. The need of the hour is to look not only for new alternative energy resources but also clean energy resources. Hydrogen is expected to be one of the most important fuels in the near future to meet the stringent emission norms.

Friction stir processing (FSP) is a method of changing the properties of metal through intense, localized plastic deformation. This deformation is produced by forcibly inserting a non-consumable tool into a workpiece, and revolving the tool in a stirring motion as it is pushed laterally through the workpiece. It comprises of a rotating tool with pin and shoulder which are inserted into a single piece of material and traversed along the desired path to cover the region of interest. Friction between the shoulder and work piece results in localized heating which raises the temperature of the material to the range where it is plastically deformed. During this process, severe plastic deformation occurs and due to thermal exposure of material, it results in a significant evolution in the local microstructure. Carbon nanotubes were dispersed into Al matrix by multipass FSP to fabricate Al6082 T0/Fe-MWCNT.

This research is an attempt to investigate the significance of Value Stream Mapping (VSM) in the lean transformation of manufacturing units (largely automotive) and then apply the same in a tool room. It is an essential tool used to interpret both material and information flow in a system. The tool room under study specializes in production of a large variety of high precision tools for the automotive industry. A product family is chosen to map and analyze various stages of its production process, starting from the raw material (R/M) to the finished goods’ (F/G) stage. VSM is then implemented in the tool room to correctly identify wastes and thus improvement areas to bridge gaps between current and future states. Both current and future state maps are drafted along with usage of other lean tools to justify its implementation in a small setup like tool room.

Bhutan is a small nation in the eastern Himalayas, between two of the world's largest neighbors and fastest-growing economies; China, and India. The GDP of the country is $2.707 Billion as of 2022. Bhutan’s largest renewable source is hydropower, which has a known potential of 30,000 MW. However, it has only been able to harvest only 1,480 MW (5% of the potential). The current overall electrification rate is 99% overall with 98.4% in rural areas. It exports 75.5% of total electricity generated in the country to India. However, the reliable supply of electricity remains a big challenge. The government is also pushing the use of renewable energy sources like solar and wind to diversify the energy mix and enhance the power security of the country. The share of renewable energy is very minimal at present amounting to 723 kW Solar PV and 600 kW Wind power.