Search Results

In some automotive electrical systems, it is advantageous to use power supplies and loads at two or more voltages. Often it is desirable to retain the single wire power architecture, with the car body providing the return circuit. A major difficulty in achieving this end is the matter of dealing with the possibility of a short circuit between feed wires at different voltages. It can be shown that source-side fuses cannot be relied upon to return the system to a safe state in all cases. Substantial effort was applied to this problem in the early years of the 21st century, but the results were less than completely satisfactory. Using entirely separate cable harnesses for each voltage, with physically separated routing, minimizes the risk of such a short occurring in the harness.

The average body weight of the US population has increased over time. This study investigates the effect of increasing weight on seat and occupant responses in 15-18 km/h and 42 km/h rear sled tests. The effect of initial occupant posture is also discussed. Seven tests were conducted with lap-shoulder belted ATDs (anthropometric test device) placed on older and modern driver seats. Four tests were conducted with a 50th percentile male Hybrid III, two with 95th percentile male Hybrid III and one with a BioRID. The ATDs were ballasted to represent a Class I or II obese occupant in three tests. The tests were matched by seat model and sled velocity. The effect of occupant weight was assessed in three matches. The results indicated an increase in seatback deflection with increasing occupant weight.

The use of Lithium-ion batteries in the transportation sector has its own unique set of requirements such as high-power demands, cooling challenges, and risk of mechanical failure due to crashes. Active and passive components of thermal management systems in battery-powered products are designed to mitigate the effects of thermal runaway events and prevent cell-to-cell propagation. Designing safe battery-powered systems requires an understanding of how the battery pack will behave while undergoing thermal runaway, including critical data such as total energy yielded, rate of energy generation, as well as venting patterns and directions. Details such as thermal runaway energy fractions associated with the cell casing as well as vent gas and ejecta can be used to inform and optimize battery pack designs and the product as a whole. The NASA Fractional Thermal Runaway Calorimeter (FTRC) was created to measure these values.

Occupant protection in rear crashes is complex. While seatbelts and head restraints are effective in rear impacts, seatbacks offer the primary restraint component to front-seat occupants in rear impacts. Seatback deflection due to occupant loading can occur in a previous rear crash and/or in multiple-rear event crashes. Seatback deflection will in-turn affect the plastic seatback deformation and energy absorption capabilities of the seat. This study was conducted to provide information on seatback deflection and seat energy consumption in low and high-speed rear impacts. The results can be used to examine seatback deflection and energy consumed in a previous rear impact, or in collisions with multiple rear impacts. Prior seatback deflection and energy absorption can affect the total remaining energy absorption and seat performance for a subsequent rear impact.

During the course of a fire and subsequent exposure to the environment, iron and low-carbon steels oxidize by two mechanisms: high temperature oxidation and atmospheric corrosion. Of particular interest to fire investigators are oxide properties and distribution that could be of use to better understand important characteristics of the fire such as the location the fire originated, the direction the fire traveled or even temperature versus time characteristics. This could be particularly valuable in cases where burn damage to combustible material, which is known to be an important indicator of fire origin, is so extensive that little if any material remains after the fire. However, there is little data in the literature that specifically addresses the utility of oxide properties in the context of fire investigations.

Fires involving cars, trucks, and other highway vehicles are a common concern for emergency responders. In 2013 alone, there were approximately 188,000 highway vehicle fires. Fire Service personnel are accustomed to responding to conventional vehicle (i.e., internal combustion engine [ICE]) fires, and generally receive training on the hazards associated with those vehicles and their subsystems. However, in light of the recent proliferation of electric drive vehicles (EDVs), a key question for emergency responders is, “what is different with EDVs and what tactical adjustments are required when responding to EDV fires?” The overall goal of this research program was to develop the technical basis for best practices for emergency response procedures for EDV battery incidents, with consideration for suppression methods and agents, personal protective equipment (PPE), and clean-up/overhaul operations.

The operational safety of automated driving system (ADS)-equipped vehicles (AVs) needs to be quantified for an understanding of risk, requiring the measurement of parameters as they relate to AVs and human driven vehicles alike. In prior work by the Institute of Automated Mobility (IAM), operational safety metrics were introduced as part of an operational safety assessment (OSA) methodology that provide quantification of behavioral safety of AVs and human-driven vehicles as they interact with each other and other road users. To calculate OSA metrics, the data capture system must accurately and precisely determine position, velocity, acceleration, and geometrical relationships between various safety-critical traffic participants. The design of an infrastructure-based system that is intended to capture the data required for calculation of OSA metrics is addressed in this paper.

Unintended acceleration events due to pedal misapplication have been shown to occur more frequently in older vs. younger drivers. While such occurrences are well documented, the nature of these movement errors is not well-characterized in common pedal error scenarios: namely, on-road, non-emergency stopping or slowing maneuvers. It is commonly assumed that drivers move in a ballistic or “direct hit” trajectory from the accelerator to the brake pedal. However, recent simulator studies show that drivers do not always move directly between pedals, with older drivers displaying more variable foot trajectories than younger drivers. Our study investigated pedal movement trajectories in older drivers ages 67.9 ± 5.2 years (7 males, 8 females) during on-road driving in response to variable traffic light conditions. Three different sedans and a pick-up truck were utilized.

The emergence of Plug-in hybrid electric vehicles (PHEVs) and electric vehicles (EVs) as a viable means of transportation has been coincident with the development of lithium-ion battery technology and electronics that have enabled the storage and use of large amounts of energy that were previously only possible with internal combustion engines. However, the safety aspects of using these large energy storage battery packs are a significant challenge to address. For example an unintentional sudden release of energy, such as through a thermal runaway event, is a common concern. Developing thermal management systems for upset conditions in battery packs requires a clear understanding of the heat generation mechanisms and kinetics associated with the failures of Li-ion batteries.

As lithium-ion cells and systems become larger and more ubiquitous in automotive applications, fire and explosion hazards that are rare or non-existent in smaller systems may exist in these larger systems. One potential hazard can occur when flammable gases emitted from a lithium-ion cell failure accumulate in or around automobiles and are ignited by electrical activity or by the cells themselves and result in a fire or explosion. In some instances, the safety aspects related to fires and explosions protection of electric vehicles and hybrid vehicles using these large energy storage battery packs are a significant challenge to address. This paper describes and characterizes the combustion and explosion hazards that can occur when a lithium ion battery pack fails and goes into thermal runaway in an enclosed space. Metrics such as gas composition, maximum overpressure, rate of pressure rise, and flammability limits are described.

This study was conducted to assess the effects of differing rear impact pulse characteristics on restraint performance, front-seat occupant kinematics, biomechanical responses, and seat yielding. Five rear sled tests were conducted at 40.2 km/h using a modern seat. The sled buck was representative of a generic sport utility vehicle. A 50th percentile Hybrid III ATD was used. The peak accelerations, acceleration profiles and durations were varied. Three of the pulses were selected based on published information and two were modeled to assess the effects of peak acceleration occurring early and later within the pulse duration using a front and rear biased trapezoidal characteristic shape. The seatback angle at maximum rearward deformation varied from 46 to 67 degrees. It was lowest in Pulse 1 which simulates an 80 km/h car-to-car rear impact.

Assessment of the physical evidence on a seat belt restraint system provides one source of data for determining an occupant’s seat belt use or non-use during a motor vehicle crash. The evidence typically associated with loading from a restrained occupant has been extensively researched and documented in the literature. However, evidence of loading to the restraint system can also be generated by other means, including the interaction of an unrestrained occupant with a stowed restraint system. The present study evaluates physical evidence on multiple stowed restraint systems generated via interaction with unrestrained occupants during a full-scale dolly rollover crash test of a large multiple passenger van. Unbelted anthropomorphic test devices (ATDs) were positioned in the driver and right front passenger seats and in all designated seating positions in the third, fourth, and fifth rows.

Previous research [1] described a procedure for creating prints from digital photographs that accurately represent critical features of visual scenes at low levels of illumination. In this procedure, observers adjust the brightness of a digital photographs captured using standard photography until it best matches the visible characteristics of the actual scene. However, standard digital photography cannot capture the full dynamic range of a scene's luminous intensities in many low-illumination settings. High dynamic range (HDR) photography has the potential to more accurately represent a viewer's perception under low illumination. Such a capability can be critical to representing nighttime roadway scenes, where HDR photography can enable the creation of more accurate photographic representations of bright visual stimuli (e.g., vehicle headlamps, street lighting) while also maintaining the integrity of the photograph's darker portions.

The increased prevalence of larger and more energy-dense battery packs for transportation and grid storage applications has resulted in an increasing number of severe battery thermal events. The implications on product reliability, consumer safety, and the surrounding environment are significant. While there are many potential root causes for battery thermal runaway, these events often start within a single battery cell or group of cells that cascade to neighboring cells and other combustible materials, rapidly increasing the hazard profile of the battery pack as more stored energy is released. Reducing these hazards requires preventing severe thermal runaway scenarios by mitigating cell-to-cell propagation through the improved design of both individual cells and battery packs.

The emergence of Plug-in hybrid electric vehicles (PHEVs) and electric vehicles (EVs) as a viable means of transportation has been coincident with the development of lithium-ion (Li-ion) battery technology and electronics. These developments have enabled the storage and use of large amounts of energy that were previously only possible with internal combustion engines. However, the safety aspects of using these large energy storage battery packs are a significant challenge to address. In addition, the rapid advances in electrode and electrolyte materials for Li-Ion batteries have made comparisons and ranking of safety parameters difficult because of the substantial variations in cell designs. In this work, we outline a method for quantifying the thermal safety aspects of Li-ion battery technologies using a Cone Calorimeter.

Motorcycle stability during a variety of maneuvers is maintained through both rider steering input and body interactions with the seat, tank, footrests, and handlebars. Exploring how rider-vehicle interactions impact vehicle control is critical to creating a comprehensive understanding of motorcycle handling. The present study aims to understand how experienced motorcycle riders influence motorcycle dynamics by characterizing center of pressure (COP) location, force applied at the seat, rider lean angle and offset relative to the motorcycle, and steering angle for various maneuvers. A course was defined on Exponent’s Test and Engineering Center (TEC) track and skid pad that included sections of straight riding, navigating a banked curve, and sharp turning (low speed U-turns, 90 degree turn after a stop, and obstacle avoidance). The task influenced rider response and, in particular, lateral COP location at the seat.

This study assesses vehicle and occupant responses in six vehicle-to-vehicle high-speed rear impact crash tests conducted at the Exponent Test and Engineering Center. The struck vehicle delta Vs ranged from 32 to 76 km/h and the vehicle centerline offsets varied from 5.7 to 114 cm. Five of the six tests were conducted with Hybrid III ATDs (Anthropometric Test Device) with two tests using the 50th male belted in the driver seat, one test with an unbelted 50th male in the driver seat, one test with a 95th male belted in the driver seat, and one with the 5th female lap belted in the left rear seat. All tests included vehicle instrumentation and three tests included ATD instrumentation. The ATD responses were analyzed and compared to corresponding IARVs (injury assessment reference values). Ground-based and onboard vehicle videos were synchronized with the vehicle kinematic data and biomechanical responses.

Vehicle rear structure stiffness has increased as a result of the requirements in the FMVSS 301R, which has also corresponded to an increase in front-row seat strength. This study evaluates the structural behavior and occupant response associated with production-level seats equipped with body-mounted D-rings, and very stiff all-belt-to-seat (ABTS) in a group of 12 deceleration sled tests. A double-haversine pulse with approximately 100-msec duration was used for all tests, with peak accelerations of approximately 19 g for the 40 km/h (25 mph) tests and peak accelerations of 28 g for the 56 km/h (35 mph) test. This generic pulse was designed to represent a severe rear impact crash involving vehicles with stiffer rear structures. The tests compared occupant responses and resulting structural deformation of an original equipment manufacturer (OEM) production-level driver seat from a pickup and a very stiff modified ABTS. Both seating systems were equipped with dual recliners.

Seat strength has increased over the past four decades which includes a transition to dual recliners. There are seat collision performance issues with stiff ABTS and very strong seats in rear impacts with different occupant sizes, seating positions and physical conditions. In this study, eight rear sled tests were conducted in four series: 1) ABTS in a 56 km/h (35 mph) test with a 50th Hybrid III ATD at MGA, 2) dual-recliner ABTS and F-150 in a 56 km/h (35 mph) test with a 5th female Hybrid III ATD at Ford, 3) dual-recliner ABTS in a 48 km/h (30 mph) test with a 95th Hybrid III ATD leaning inboard at CAPE and 4) dual-recliner ABTS and Escape in 40 km/h (25 mph) in-position and out-of-position tests with a 50th Hybrid III ATD at Ford. The sled tests showed that single-recliner ABTS seats twist in severe rear impacts with the pivot side deformed more rearward than the stanchion side.

This study assesses the exposure distribution and injury rate (MAIS 4+F) to front-outboard non-ejected occupants by crash severity, belt use and head restraint type and damage in rear impacts using 1997-2015 NASS-CDS data. Rear crashes with a delta V <24 km/h (15 mph) accounted for 71% of all exposed occupants. The rate of MAIS 4+F increased with delta V and was higher for unbelted than belted occupants with a rate of 11.7% ± 5.2% and 6.0% ± 1.5% respectively in 48+ km/h (30 mph) delta V. Approximately 12% of front-outboard occupants were in seats equipped with an integral head restraint and 86% were with an adjustable head restraint, irrespective of crash severity. The overall injury rate was 0.14% ± 0.05% and 0.22% ± 0.06%, respectively. It was higher in cases where the head restraint was listed as “damaged”. Thirteen cases involving a lap-shoulder belted occupant in a front-outboard seat in which “damage” to the adjustable head restraint was identified.