Search Results

This paper describes the development of an analytical method to assess and optimize halfshaft joint angles to avoid excessive 3rd halfshaft order vibrations during wide-open-throttle (WOT) and light drive-away events. The objective was to develop a test-correlated analytical model to assess and optimize driveline working angles during the virtual design phase of a vehicle program when packaging tradeoffs are decided. A twelve degree-of-freedom (12DOF) system model was constructed that comprehends halfshaft dynamic angle change, axle torque, powertrain (P/T) mount rate progression and axial forces generated by tripot type constant velocity (CV) joints. Note: “tripot” and “tripod” are alternate nomenclatures for the same type of joint. Simple lumped parameter models have historically been used for P/T mount optimization; however, this paper describes a method for using a lumped parameter model to also optimize driveline working angles.

A task group within the SAE Automotive Corrosion and Protection (ACAP) Committee continues to pursue the goal of establishing a standard test method for in-laboratory cosmetic corrosion evaluations of finished aluminum auto body panels. The program is a cooperative effort with OEM, supplier, and consultant participation and is supported in part by USAMP (AMD 309) and the U.S. Department of Energy. Numerous laboratory corrosion test environments have been used to evaluate the performance of painted aluminum closure panels, but correlations between laboratory test results and in-service performance have not been established. The primary objective of this project is to identify an accelerated laboratory test method that correlates with in-service performance. In this paper the type, extent, and chemical nature of cosmetic corrosion observed in the on-vehicle exposures are compared with those from some of the commonly used laboratory tests

General Motors (GM) recently purchased an acoustic holography system based on the Helmholtz Equation Least Squares (HELS) methodology. Typically acoustic holography has utilized planar transformation of the Fourier acoustic equations. General Motors conducted a variety of experiments on a simple well understood structure. This enabled us to understand the setup parameters and confirm the manufacturer's claims for accuracy. Measurements on the structure were taken using the HELS based equipment and a laser vibrometer. Conclusions are drawn on how to set up the equipment for future testing on vehicles.

The need for improved axle NVH integration has increased significantly in recent years with industry trends toward full-time and automatic four wheel drive (4wd) systems. Along with seamless 4wd operation, quiet performance has become a universal expectation. Axle gear-mesh noise can be transmitted to the vehicle passenger compartment through airborne paths (not discussed in this paper) and structure-borne paths (the focus of this paper.) A variety of mounting configurations are used in an attempt to provide improved axle isolation and reduce structure-borne transmission of gear-mesh noise. The configuration discussed in this paper is a 4-point vertical mount design for an Independent Front Drive Axle (IFDA). A significant benefit of this configuration is improved isolation in the range of drive torques where axle-related NVH issues typically exist.

The need for fuel economy gains is crucial in todays automotive market. There is also growing interest and knowledge of greenhouse gases and their effect on the environment. Paulstra's magnesium powertrain brackets were a solution that was presented not just to reduce the weight of the engine mounting system (which was already under its weight target before magnesium introduction), but in response of the OEM's desire to further reduce the weight of the vehicle for CAFE and weight class impact. This new engine mounting system has three powertrain mount brackets that are high-pressure die cast AZ91D magnesium alloy. This paper will show that these brackets to have a dramatic weight reduction compared to the standard aluminum die-cast material that they replaced. This paper describes the process of approval: concept and material sign-off by the OEM, FEA for strength and modal performance, corrosion, and the final product.

The GM Aerodynamics Laboratory (GMAL) was modified in 2001 to reduce the background noise level and provide a semi-anechoic test section for wind noise testing. The walls and ceiling of the test section were lined with acoustic foam and foam-filled turning vanes were installed in the corners. Portions of the wind tunnel circuit were also treated with fiberglass material covered by perforated sheet metal panels. High skin drag due to roughness of the foam surfaces, along with high blockage due to the large turning vanes, increased the wind tunnel circuit losses so that the maximum wind speed in the test section was reduced. The present study calculates the averaged total pressure losses at three locations to evaluate the reductions in skin drag and blockage from proposed modifications to the circuit, which were intended to increase the test section wind speed without compromising noise levels.

The unsteady flow fields behind two different automobile outside side rear view mirrors were examined experimentally in order to obtain a comprehensive data base for the validation of the ongoing computational investigation effort to predict the aero-acoustic noise due to the outside rear view mirrors. This study is part of a larger scheme to predict the aero-acoustic noise due to various external components in vehicles. To aid with the characterization of this complex flow field, mean and unsteady surface pressure measurements were undertaken in the wake of two mirror models. Velocity measurements with particle image velocimetry were also conducted to develop the mean velocity field of the wake. Two full-scale mirror models with distinctive geometrical features were investigated.

The impact of ultra thinwall catalysts on TIER2 emission performance, packaging and total system cost was evaluated. The primary focus was to compare ultra-thinwall and thinwall cell configurations (400/3, 400/4, 600/2, 600/3, 600/3 hex, 900/2, and 1200/2) with a baseline 600/4 at constant substrate volume, washcoat and PGM loading. Other areas investigated included the evaluation of decreasing catalyst volume while maintaining constant or increased mass transfer capabilities while holding washcoat and PGM loadings constant. The emissions impact of varying washcoat and PGM loading was measured on specific substrates, including a comparison of square to hex cell. Backpressure for each configuration was calculated with the Corning substrate pressure drop modeling tool. Converters were rapid aged on dynamometers reflecting approximately a 50,000 mile aged performance. Emission testing was completed using the FTP test cycle.

The Auto/Steel Partnership Corrosion Project Team has completed a perforation corrosion test program consisting of on-vehicle field exposures and various accelerated tests. Steel sheet products with eight combinations of metallic and organic coatings were tested, utilizing a simple crevice coupon design. On-vehicle exposures were conducted in St. John's and Detroit for up to seven years to establish a real-world performance standard. Identical test specimens were exposed to the various accelerated tests, and the results were compared to the real-world standard. This report documents the results of these tests, and compares the accelerated test results (including SAE J2334, GM9540P, Ford APGE, CCT-I, ASTM B117, South Florida Modified Volvo, and Kure Beach (25-meter) exposures) to the on-vehicle tests. The results are compared in terms of five criteria: extent of corrosion, rank order of material performance, degree of correlation, acceleration factor, and control of test environment.

Interior noise has become a significant performance attribute in modern passenger vehicles and this is extremely important in the luxury market segment where a quiet interior is the price of entry. With the elimination of early prototype vehicles to reduce development costs, high frequency analytical SEA models are used to design the vehicle sound package to meet targets for interior noise quality. This function is important before representative NVH prototypes are available, and later to support parameter variation investigations that would be cost prohibitive in a hardware test. This paper presents the application of an analytical full vehicle SEA model for the development of the acoustic package of a cross over luxury utility vehicle. The development concerns addressed were airborne powertrain noise and road noise. Power flow analysis was used to identify the major noise paths to the interior of the vehicle.

Over the years different methods of vehicle interior noise development have been used by car companies. During my 38 plus years of experience with General Motors' Noise and Vibration Laboratory and Advanced Vehicle Development Center, I have worked with varying methods, and when looking back, these methods have fluctuated between the application of highly subjective analysis and highly objective analysis. Stepped up efforts to reduce overall vehicle engineering design and development time have intensified the use of computer modeling techniques. Iterations of acoustic package content proposals once done experimentally can now be accomplished, to some degree, with computer analysis. To achieve appropriate sound1 character that meets consumer expectations will require both subjective analysis and objective testing and analysis early in a vehicle program.

The paper presented a correlation work between the GM and Goodyear acoustical laboratories to determine the tire noise load cases used for vehicle tire noise allocation and high-frequency airborne noise analysis. A large group of tires with different sizes were tested in the two labs to examine the lab-to-lab load cases differences in terms of near-field sound intensity and far-field sound power. A good agreement was found for the noise ranking between the two labs by 1/3 octave band and overall A-weighted sound intensity and sound power. The correction factors could be determined from one lab to another as well as from the near-field sound intensity to the far-field sound power. The discrepancies were investigated by comparing the two fixtures and two dyno shell profiles. The differences in 1/3 octave band sound measurement between the two labs were found to be contributed mainly by the shell profiles.

This paper will examine the regulatory development process, discuss the technical principles of the Economic Commission for Europe (ECE), R51.03 test, and discuss the overall objectives of the ECE R51.03 noise emission regulation. The development of this global noise emission regulation was a multi-stakeholder process which has resulted in new test procedures and new noise emission regulation principles. New test procedures based on ISO 362-1:2015 move the test basis to representative in-use noise emission, independent of vehicle propulsion technology. As part of the regulatory development, a monitoring program was conducted by the European Union to assess the applicability of the proposed test to provide representative vehicle noise emission results. The monitoring results also provided the basis to determine equivalent stringency between the test procedures of ECE R51.02 and R51.03.

Powertrain mounting systems design and development involves creating and optimizing a solution using specific mount rates and evaluation over multiple operating conditions. These mount rates become the recommended “nominal” rates in the specifications. The powertrain mounts typically contain natural materials. These properties have variation, resulting in a tolerance around the nominal specification and lead to differences in noise and vibration performance. A powertrain mounting system that is robust to this variation is desired. The design and development process requires evaluation of these mounts, within tolerance, to ensure that the noise and vibration performance is consistently met. During the hardware development of the powertrain mounting system, a library of mounts that include the range of production variation is studied. However, this is time consuming.

As the automobile industry is moving towards Electrical vehicles, it becomes very important to have low cost and robust solution to seal all the internal Battery sub systems. It’s a known fact that various IC engine Vehicles are already using Room temperature vulcanized rubber (RTV) for many metal and composite sealing interfaces. Nevertheless, it always needs a good structural design to have good sealing performance. For designing a robust RTV joint for composite structures, it becomes important to have standard RTV chamfers. Sometimes even with these standards, it becomes very costly in having warranty issues when we have weak structure around RTV chamfers. Any joint structure involves multiple design parameters which might impact the sealing performance. Some of the joint structural parameters should be well designed at the early phase of product development cycle, which otherwise will later add lot of cost in modifying the product with its integrated components.

This paper describes the design and development of the rear compartment structure of the sixth generation Corvette, C6, which starts in the 2005 model year. The improved design integrates the rear compartment packaging to address issues seen on fifth generation Corvette, C5. The molded composite fiberglass reinforced, tub and surround panels are similar to the C5. These large panels are modified to fit the new styling theme of the C6, while also addressing the packaging requirements of the updated underbody structure and exhaust system. New composite side support brackets and cross car reinforcement combine to address several desired improvements. These side support brackets are designed to package the rear audio speakers, electrical modules, wiring and cable routing while also addressing build variation and localized stiffness improvement. The side brackets support the surround panel increasing the manufacturing control of the surround panel.

This paper discusses the recent growth in aluminum wheel popularity and the problems associated with maintaining the wheel's appearance and corrosion protection. The various options in wheel coatings are then described as well as the adverse wheel environment. Finally, the variables affecting wheel corrosion resistance are explained and the testing that is undertaken to evaluate the performance characteristics of the wheel coating.

Substituting alternative materials for conventional materials in automotive applications is an important strategy for reducing environmental burdens over the entire life cycle through weight reduction. Strong, light carbon composites and lightweight metals can potentially be used for components such as body structure, chassis parts, brakes, tie rods, or instrument panel structural beams. There are also proposed uses in conventional and alternative powered vehicles for other advanced materials, including synthetic graphite, titanium, and metals coated with graphite composite, that have special strength, hardness, corrosion resistance, or conductivity properties. The approach used in this paper was to compare the environmental life cycle inventory of parts made from carbon fiber-thermoplastic composites, synthetic graphite, titanium, and graphite coated aluminum, with parts made from conventional steel or aluminum.

The paper analyzes the mechanism of automobile millimeter wave radar noise, this paper does not study radar noise from the angle of signal processing, but from the level of false detection and missed detection, at the same time, the noise mechanism is modeled and verified. Firstly, the purpose and significance of the research of radar vehicle noise are described, and then, we summarize and outline the macro phenomenon and the specific characteristics of the automobile millimeter wave radar noise.

This paper presents an overview of the aerodynamic development of the 2019 Chevrolet Corvette C7 ZR1. Extensive wind tunnel testing and computational fluid dynamics simulations were completed to engineer the ZR1’s aerodynamics to improve lift-to-drag efficiency and track capability over previous Corvette offerings. The ZR1 architecture changes posed many aerodynamic challenges including increased vehicle cooling, strict packaging demands, wider front track width, and aggressive exterior styling. Through motorsports-inspired aerodynamic development, the ZR1 was engineered to overcome these challenges through the creation of new devices such as a raised rear wing and front underwing. The resulting Standard ZR1 achieved a top speed of 212 mph making it the fastest Corvette ever [1]. Optionally, the ZR1 with the ZTK Performance Package provides the highest downforce of any Corvette, generating approximately 950 pounds at the ZTK’s top speed [1].