Search Results

General Motors' (GM) eAssist powertrain builds upon the knowledge and experience gained from GM's first generation 36Volt Belt-Alternator-Starter (BAS) system introduced on the Saturn VUE Green Line in 2006. Extensive architectural trade studies were conducted to define the eAssist system. The resulting architecture delivers approximately three times the peak electric boost and regenerative braking capability of 36V BAS. Key elements include a water-cooled induction motor/generator (MG), an accessory drive with a coupled dual tensioner system, air cooled power electronics integrated with a 115V lithium-ion battery pack, a direct-injection 2.4 liter 4-cylinder gasoline engine, and a modified 6-speed automatic transmission. The torque-based control system of the eAssist powertrain was designed to be fully integrated with GM's corporate common electrical and controls architectures, enabling the potential for broad application across GM's global product portfolio.

This paper describes the development of an improved method for Noise and Vibration (N&V) chassis dynamometer testing using Road Load Simulation (RLS). Powertrain-induced noise and vibration testing on a chassis dynamometer has commonly been conducted using fixed loads or simplistic load versus speed approximations. Simple speed control and load control dyno test conditions are largely sufficient to provide representative noise and vibration performance assessment when the powertrain and its controls are insensitive to differences between the actual road load and the dyno load. With the recent growth of advanced engine control systems and hybrid powertrains, more representative road load simulation is required to ensure proper operation of the increasingly sophisticated and diverse powertrain and chassis control systems. Proper exercise of these control systems often determines the quality of the noise and vibration data.

Limited-slip differentials improve traction and handling when compared to open differentials, but offer no active modulation and can compromise typical driving. A number of passive control systems exist that attempt to reduce this compromise. Electronically controlled limited-slip differentials (eLSD) are being introduced that allow active control of the differential in all driving situations and can be operated as an open differential, a fully locked differential, or at any point between these extremes. Such an eLSD system was implemented in two General Motors front wheel drive cars-one on an automatic transmission and applied by the transmission pump, the other on a manual transmission and applied by an external pump. This eLSD system contains a multi-plate wet clutch connected to the differential carrier and right side half-shaft of an all wheel drive capable transmission.

In the North American automotive market, cylinder deactivation by means of engine valve deactivation is becoming a significant enabler in reducing the Brake Specific Fuel Consumption (BSFC) of large displacement engines. This allows for the continued market competitiveness of large displacement spark ignition (SI) engines that provide exceptional performance with reduced fuel consumption. As an alternative to a major engine redesign, the Active Fuel Management™ (AFM™) system is a lower cost and effective technology that provides improved fuel economy during part-load conditions. Cylinder deactivation is made possible by utilizing innovative new base engine hardware in conjunction with an advanced control system. In the GM 3.9L V-6 Over Head Valve (OHV) engine, the standard hydraulic roller lifters on the engine's right bank are replaced with deactivating hydraulic roller lifters and a manifold assembly of oil control solenoids.

Vehicle dynamics simulation with Hardware In the Loop (HIL) has been demonstrated to reduce development and validation time for dynamic control systems. For dynamic control systems such as Anti-lock Braking System (ABS) and Electronic Stability Control (ESC), an accurate vehicle dynamics performance simulation system requires the Electronic Brake Control Module (EBCM) coupled with the vehicles brake system hardware. This kind of HIL simulation-specific software tool can further increase efficiency by means of automation and optimization of the development and validation process. This paper presents a method for HIL vehicle dynamics simulator optimization through Brake Response Time (BRT) correlation. The paper discusses the differences between the physical vehicle and the HIL vehicle dynamics simulator. The differences between the physical and virtual systems are used as factors in the development of a Design Of Experiment (DOE) quantifying HIL simulator performance.

The increasing usage of brake-by-wire systems in the automotive industry has provided manufacturers with the opportunity to improve both vehicle and manufacturing efficiency. The replacement of traditional mechanical and hydraulic control systems with electronic control devices presents different potential vehicle-level safety hazards than those presented by conventional braking systems. The proper design, development, and integration of a brake-by-wire control system requires that hazards are reasonably prevented or mitigated in order to maximize the safety of the vehicle operator, occupant(s), and passers-by.

To realize better fuel economy benefits from transmissions, car makers have started the application of torque converter clutch control in second gear and beyond, resulting in greater demand on the torque converter clutch (TCC) and its control system. This paper focuses on one aspect of the control of the torque converter clutch to improve fuel economy and faster response of the transmission. A TCC is implemented to control the slip between the pump and turbine of the torque converter, thereby increasing its energy transfer efficiency and increasing vehicle fuel economy. However, due to the non-linear nature of the torque converter fluid coupling, the slip feedback control has to be very active to handle different driver inputs and road-load conditions, such as different desired slip levels, changes in engine input torques, etc. This non-linearity requires intense calibration efforts to precisely control the clutch slip in all the scenarios.

The engineering of electric propulsion systems requires time and cost efficient methodologies to determine system characteristics as well as potential component integration issues. A significant part of this analysis is the identification of the electromagnetic fields present in the propulsion system. Understanding of the electromagnetic fields during system operation is a significant design consideration due to the use of components that require large current(s) and high voltage(s) in the proximity of other control system items (such as sensors) that operate with low current(s) and voltage(s). Therefore, it is critical to quantify the electromagnetic fields produced by these components within the design and how they may interact with other system components. Often overlooked (and also extremely important) is an evaluation of how the overall system architecture can generate or react to electromagnetic fields (which may be a direct result of packaging approaches).

As customer dissatisfaction with interior trim components is tracked by the JDPowers question on “surface durability”, there is a need to increase the durability of the parts that are molded in color. In particular, door trim panel lowers are susceptible to surface damage which results in an unfavorable appearance. To address this issue, an assessment of the various factors that can affect surface durability was conducted using talc filled TPO materials in order to determine the optimum set of physical properties. The team used Design for Six Sigma (DFSS) methodology. A Taguchi orthogonal experiment was used and included control system factors of material, grain, gloss, and color. Noise factors included molding process parameters, aging, and piece to piece variation. The output was a measure of the scratch resistance of the molded plaque which was defined by a Delta L calculation.

As the automotive industry moves toward producing more advanced hybrid/electric vehicles, high voltage Rechargeable Energy Storage Systems (RESS) are now being implemented as the main power source of the vehicle, replacing the need for the traditional Internal Combustion Engine (ICE) altogether or just during certain parts of a drive cycle. With this type of architecture, it is becoming a necessity to equip these vehicles with devices that can draw their power from the high voltage (HV) RESS. These HV devices are not only used to support the propulsion of the vehicle but to perform other necessary vehicle functions as well. With demands of high voltage power from multiple systems ranging from RESS thermal conditioning, cabin thermal conditioning, RESS charging, and vehicle propulsion, power demands can exceed the available power of the vehicle. This creates a perplexing problem of how to manage the high voltage power consumption between the different vehicle systems.

The development and validation of an electric vehicle presents numerous issues that are not normally encountered during the development of a traditional internal combustion powered vehicle. Many of the issues that are encountered involve components that are common to both electric and internal combustion vehicles but are utilized in new or unique ways that may present challenges during the development process. The integration of the electric motors, power supply, batteries, and associated content into a traditional vehicle can bring new and challenging issues to light. This paper discusses the solution for an issue that arose during the testing and development of the chassis and powertrain hardware of an electric vehicle. In particular, the large rotational inertia of the electric drive motor presented significant challenges when it was accelerated by forces that were external to the drive unit.

Historically, power steering shudder, a vibration which occurs while steering a vehicle at low speeds, has been approached with systematic component-swapping experiments. This approach was time consuming and did not necessarily yield satisfactory results. In this paper it is shown that steering shudder can be analytically approached as a control system with a closed-loop limit cycle caused by the interaction of the chassis and the steering system. This approach provides a metric for determining a vehicle's propensity to shudder and allows quick predictions of the results of changing components. The approach is model-based, and incorporates chassis and hydraulic system components. Results obtained from the control systems analysis have been validated by a vehicle study, which showed a strong correlation between subjective evaluations and the stability metric provided by the analysis.

Today many vehicles are being developed with advanced computing and sensing technologies. These new technologies have contributed in enhancing driving safety and convenience. As an example, the Adaptive Cruise Control (ACC) can automatically adjust the vehicle speed to driver's set speed and maintain the driver-requested headway distance to the lead vehicle. In this paper, we further consider the automatic control of speed according to the road attributes, e.g., the speed limit and curve of the road. Two new features, ‘speed limit follower’ and ‘curve speed control’ algorithms, are proposed in this paper. These new features communicate with the conventional ACC system and control the vehicle speed while traveling across different curved roads and speed limit zones. These new features were developed as an independent function, so they can be integrated with any other existing ACC systems.

With rapid increase of vehicles on the road, safety concerns have become increasingly prominent. Since the leading cause of many traffic accidents is known to be by human drivers, developing autonomous vehicles is considered to be an effective approach to solve the problems above. Although trajectory tracking plays one of the most important roles on autonomous driving, handling the coupling between trajectory-tracking control and ESP under certain driving scenarios remains to be challenging. This paper focuses on trajectory-tracking control considering the role of ESP. A vehicle model is developed with two degrees of freedom, including vehicle lateral, and yaw motions. Based on the proposed model, the vehicle trajectory is separated into both longitudinal and lateral motion. The coupling effect of the vehicle and ESP is analyzed in the paper. The lateral trajectory-tracking algorithm is developed based on the preview follower theory.

In recent decades, significant technological advances have made cruise control systems safer, more automated, and available in more driving scenarios. However, comparatively little progress has been made in optimizing vehicle efficiency while in cruise control. In this paper, two distinct strategies are proposed to deliver efficiency benefits in cruise control by leveraging flexibility around the driver’s requested set speed, and road information that is available on-board in many new vehicles. In today’s cruise control systems, substantial energy is wasted by rigidly controlling to a single set speed regardless of the terrain or road conditions. Introducing even a small allowable “error band” around the set speed can allow the propulsion system to operate in a pseudo-steady state manner across most terrain. As long as the vehicle can remain in the allowed speed window, it can maintain a roughly constant load, traveling slower up hills and faster down hills.

In a parallel hybrid electric vehicle, higher fuel economy gains are typically achieved if significant electric drive (or engine-off) operation is possible, shifting the engine operating schedule so that it only runs at medium to high load for best efficiency. To enable efficient engine-off driving, a typical configuration will have a disconnect clutch between the engine and the rest of the driveline. In some configurations, when engine-on operation is requested the disconnect clutch is applied in conjunction with the traction motor/generator to crank the engine (i.e., a flying engine start). In this paper we describe the development of a control system for a flying engine start using an engine disconnect clutch. The clutch is located between the engine and electric motor, which is connected to the input of a multispeed transmission. We first describe an initial control algorithm evaluation using a driveline model.