Search Results

In a state-of-the-art lean-burn spark ignition engine, a strong in-cylinder flow field with enhanced turbulence intensity is formed, and understanding the wall heat transfer mechanism of such a complex flow is required. The flow velocity and temperature profiles inside the wall boundary layer are strongly related to the heat transfer mechanism. In this study, two-dimensional three-component (2D3C) velocity distribution near the piston top surface was measured during the compression stroke in a strong tumble flow using a rapid compression and expansion machine (RCEM) and a stereoscopic micro-PIV system. The bore, stroke, compression ratio, and compression time were 75 mm, 128 mm, 15, and 30 ms (equivalent to 1000 rpm), respectively.

It is well known that lubricating oil consumption (LOC) is much affected by the cylinder bore deformation occurring within internal combustion engines. There are few analytical reports, however, of this relationship within internal combustion engines in operation. This study was aimed at clarifying the relationship between cylinder bore deformation and LOC, using a conventional in-line four-cylinder gasoline engine. The rotary piston method developed by the author et al. was used to measure the cylinder bore deformation of the engine’s cylinder #3 and cylinder #4. In addition, the sulfur tracer method was applied to measure LOC of each cylinder. LOC was also measured by changing ring tension with a view to taking up for discussion how piston ring conforms to cylinder, and how such conformability affects LOC. Their measured results were such that the cylinder bore deformation was small in the low engine load area and large in the high engine load area.

In order to investigate the mechanism of heat transfer on the chamber wall of direct-injection diesel engines, 2-D temperature imaging and heat flux measurement in the flame impinging region on the chamber wall were conducted using laser-induced phosphorescence technique. The temperature of the chamber wall surface was measured by the calibrated intensity variation of the 355nm-excited laser-induced phosphorescence from an electrophoretically deposited thin layer of La2O2S:Eu phosphor on a quartz glass plate placed in a rapid compression and expansion machine (RCEM). Instantaneous 2-D images of wall temperature at different timings after start of injection and time-resolved (10kHz) heat flux near the flame impinging region were obtained for combusting and non-combusting diesel sprays with impinging distance of 23.4mm at different injection pressures (80 and 120MPa).

Furuhama(1)* proposed the new two ring package consist of a pressure ring and a narrow single-rail oil ring (NSOR) in 1985. Number of studies(2) have been done for the purpose of reducing the oil consumption (OC) in this ring package. However, OC reduction problem has been still remaining to solve as only one serious problem of this ring package. The reasons of a larger OC in the new ring package than the conventional three ring has been hardly understood, considering the OC control ability on second ring in three ring package will not so large since the fact that the oil film thickness is thicker than that of the oil ring. In this study, the mechanism of OC increase in new ring package was found out at last, as a result, OC of new ring package piston was improved up to the same level of conventional three ring package piston.

Using small thin-film pressure sensors deposited onto a piston skirt surface, oil-film pressure on the piston skirt surface is measured when piston slap noise is generated without affecting the surface geometry, stiffness and mass of the piston. Under a no-load firing engine condition and at low temperature, the measured oil-film pressure corresponded well to the measured acceleration of the cylinder liner, which is indicative of piston slap noise, confirming the validity of the present method. Moreover, the oil-film pressure distribution on the skirt surface was measured for different engine speeds and piston pin offsets, which enabled more insight to be provided into piston secondary motion than that by considering the effects of cylinder liner acceleration.

The purpose of this study is to clarify the state of heat loss to the cylinder liner of the tested engine of which piston and cylinder head were previously measured. The authors' group developed an original measurement technique of instantaneous surface temperature at the cylinder liner wall using thin-film thermocouples. The temperature was measured at 36 points in total. The instantaneous heat flux was calculated by heat transfer analysis using measurement results of the temperature at the wall. As a result, the heat loss ratio to all combustion chamber walls is evaluated except the intake and exhaust valves.

In this study, the combustion characteristics of diesel flame achieved in a rapid compression and expansion machine (RCEM) at various patterns of oxygen distribution in the chamber are investigated in order to clarify the effect of heterogeneity of oxygen distribution in diesel engines induced by EGR on the soot and NOx emissions. To make the heterogeneous distribution of oxygen in a combustion chamber, the mixtures with different oxygen concentrations are injected through the each different port located on the cylinder wall. Results indicate that the amount of oxygen entrained into the spray upstream the luminous flame region affects the NO emission from diesel flame strongly.

The method was established to identify the dynamic stiffness of the engine mount using modal parameters acquired from experimental modal analysis. Vibration tests were conducted using actual large outboard motor the BF225 (165 kW), and the dynamic stiffness of the mounts was identified. The results show that this method can identify the engine mount dynamic stiffness more adequately than the conventional method, even when the engine mounts are subjected to loads corresponding to thrust force or even in the case that the stiffness of the parts supporting an outboard motor is low.

A newly developed small-sized IES (inductive energy storage) circuit with static induction thyristor at turn-off action was successfully applied to an ignition system. This IEC circuit can generate repetitive nanosecond pulse discharges. In this paper, the ignition system using repetitive nanosecond pulse discharges was investigated as an alternative to conventional spark ignition systems. The experiments were conducted using spherically expanding flame configuration for CH4 and C3H8-air mixtures under various conditions. In conclusions, the ignition system using repetitive nanosecond pulse discharges was found to extend lean flammability limits compared with conventional spark ignition systems. In addition, the ignition system using repetitive nanosecond pulse discharges could shorten ignition delay time.

This paper describes measurements of oil film thickness of piston ring packages which have different oil control rings. The oil film thickness measurements were taken at three points, namely, the piston thrust side, front side and rear side, by the Laser Induced Fluorescence Method(LIF). One of the main findings is that the oil film thickness on the thrust side varies greatly from cycle to cycle, while cyclic variations are smaller on the front and rear sides. This difference is due to the smaller inclination of the oil control rings on the front and rear sides, compared with that on the thrust side. It is also found that oil consumption has a good correlation with oil film thickness on the thrust side and that the thrust side oil film thickness becomes thinner as the oil ring becomes narrower.

Exhaust-gas recirculation (EGR) causes the piston rings and cylinder liners of a Diesel engine to suffer abnormal wear on the sliding parts. The present study aimed at making clear such abnormal wear structurally by examining the state of lubrication of the piston with a floating liner method, observing directly a visualized cylinder and experimenting on a Diesel engine for wear. As a result, it was confirmed that soot in EGR gas would change a lot the characteristics of the piston friction force. There are two mechanisms: one directly enters the sliding surfaces, and the other enters the ring rear, applying more load to them. It was also confirmed that the level of wear on the piston ring would vary to a large extent as the state of lubrication changed.

This paper deals with the friction performance results for various new concept piston skirt profiles. The program was conducted under the assumption that friction performance varies by the total amount of oil available at each crank angle in each stroke and the instantaneous distribution of the oil film over the piston skirt area. In previous papers [1,2] it was that lower friction designs would be expected to show higher skirt slap noise. This paper discusses the correlation between friction and skirt slap for each new concept profile design. Finally, this paper explains the friction reduction mechanism for the test samples for each stroke of the engine cycle by observing the skirt movement and oil lubrication pattern using a visualization engine.

A newly developed small-sized IES (inductive energy storage) circuit with a semiconductor switch at turn-off action was successfully applied to an ignition system. This IES circuit can generate repetitive nanosecond pulse discharges. An ignition system using repetitive nanosecond pulse discharges was investigated as an alternative to conventional spark ignition systems in the previous papers. Experiments were conducted using constant volume chamber for CH₄ and C₃H₈-air mixtures. The ignition system using repetitive nanosecond pulse discharges was found to improve the inflammability of lean combustible mixtures, such as extended flammability limits, shorted ignition delay time, with increasing the number of pulses for CH₄ and C₃H₈-air mixtures under various conditions. The mechanisms for improving the inflammability were discussed and the effectiveness of IES circuit under EGR condition was also verified.

Aiming at the improvement in piston lubrication and the reduction of piston friction loss under this study, piston friction forces of cylinders with different surface roughness and treatment methods have been measured by means of a floating liner method, and the piston surface conditions have been also observed. As a result, it is found that the piston lubrication can be markedly improved by reducing the cylinder surface roughness. It is also verified that the deterioration in lubrication can be reduced even if some low viscosity oil is used, and the effect on the friction loss reduction becomes greater by reducing the piston surface roughness. On the other hand, it is found that many small vertical flaws are generated on the cylinder surface by reducing the surface roughness. In order to cope with this problem, etching and DLC (Diamond Like Carbon) coating have been tested as the surface treatments. As a result, it is confirmed that DLC coating is effective for the above.

Hydrogen can be readily used in spark-ignition engines as a clean alternative to fossil fuels. However, a larger burning velocity and a shorter quenching distance for hydrogen as compared with hydrocarbons bring a larger cooling loss from burning gas to the combustion-chamber wall. Because of the large cooling loss, the thermal efficiency of a hydrogen-fueled engine is sometimes lower than that of a conventionally fueled engine. Therefore, the reduction of the cooling loss is very important for improving the thermal efficiency in hydrogen-combustion engines. On the other hand, the direct-injection stratified charge can suppress knocking in spark-ignition engines at near stoichiometric overall mixture conditions. Because this is attributed to a leaner end gas, the stratification can lead to a lowered temperature of burning gas around the wall and a reduced cooling loss.

This study has been conducted aiming at reductions of piston slap noise and piston friction loss, and effects of lubricating oil supply between the piston skirt and cylinder on diesel engine have been verified through a series of experiments. Namely, lubricating oil was supplied forcibly into the piston skirt from outside of engine, and its effects on the cylinder block vibration, piston friction force, slap motion and oil consumption have been measured. As a result, it has been verified that the supply of a small amount of oil (6mL/min) to the piston skirt reduces about 50 % of the block vibration caused by the piston slap motion in idling operation, and about 20 % of the piston friction loss in full load operation. Furthermore it has verified without giving any significant adverse effect on oil consumption.

Reformed fuel from hydrocarbons or alcohol mainly consists of hydrogen, carbon monoxide and carbon dioxide. The composition of the reformed fuel can be varied to some extent with a combination of a thermal decomposition reaction and a water gas shift reaction. Methanol is known to decompose at a relatively low temperature. An application of the methanol reforming system to an internal combustion engine enables an exhaust heat recovery to increase the heating value of the reformed fuel. This research analyzed characteristics of combustion, exhaust emissions and cooling loss in an internal combustion engine fueled with several composition of model gases for methanol reformed fuels which consist of hydrogen, carbon monoxide and carbon dioxide. Experiments were made with both a bottom view type optical access single cylinder research engine and a constant volume combustion chamber.

Hydraulically damped rubber engine mounts (HDM) are an effective means of providing sufficient isolation from engine vibration while also providing significant damping to control the rigid body motions of the engine during normal driving conditions. This results in a system which exhibits a high degree of non-linearity in terms of both frequency and amplitude. The numerical simulation of vibration isolation characteristics of HDM is difficult due to the fluid-structure interaction between the main supporting rubber and fluid in chambers, the nonlinear material properties, the large deformation of rubber parts, structure contact problems among the inner parts, and the turbulent flow in the inertia track. In this paper an integrated numerical simulation analysis based on structural FEM and a lumped-parameter model of HDM is carried out.

Thermodynamic characteristics of premixed compression ignition combustions were clarified quantitatively by heat balance estimation. Heat balance was calculated from temperature, mole fractions of intake and exhaust gases, mass and properties of fuels. Heat balance estimation was conducted for three types of combustion; a conventional diesel combustion, a homogeneous charge compression ignition (HCCI) combustion; fuel is provided and mixed with air in an intake pipe in this case, and an extremely early injection type PREmixed lean DIesel Combustion (PREDIC). The results show that EGR should be applied for premixed compression ignition combustion to complete combustion at lower load conditions and to control ignition timing at higher load conditions. With an application of EGR, both HCCI and PREDIC showed low heat loss characteristics at lower load conditions up to 1/2 load.

This study analyzes the factors influencing the thermal efficiency of a homogeneous charge spark-injection (SI) engine fuelled with hydrogen, focusing on the degree of constant volume and cooling loss. The cooling loss from the burning gas to the cylinder walls is quantitatively evaluated by analyzing the cylinder pressure diagram and exhaust gas composition. The degree of constant volume burning and constant volume cooling are also obtained by fitting the Wiebe function to the rate of heat release calculated using the cylinder pressure diagram. A comparison of combustion and cooling characteristics of hydrogen and methane combustion reveals that cooling loss in hydrogen combustion is higher than that of methane combustion due to the short quenching distance and rapid burning velocity during hydrogen combustion. It is also suggested that the high cooling loss observed during hydrogen combustion reduces thermal efficiency.