Search Results

This study focused on European NCAP activities of introducing a new head protection evaluation procedure, as proposed by BASt (Federal Highway Research Institute - GERMANY). Various kinds of E-bikes are available in the market, ranging from E-bikes that have a small motor to assist the rider’s pedal-power i.e., pedelecs to somewhat more powerful E-bikes which is similar to a moped-style scooter. This paper focused on identifying the factors influencing bicyclist head kinematics during bicycle vs. passenger vehicle (PV) collisions at the intersection. Two AM50 bicyclist FE models are developed using i) GHBMC Human Body Model (HBM) and ii) WorldSID (WS) side impact dummy. Head kinematics of bicyclists of pedal-assist E-bike and normal bike were compared using CAE simulation. It is found that the vehicle’s impact velocity, type of bicycle, the mass of E-bike and bicycle traveling speed will influence the head kinematics.

Detergent additives in automotive gasoline fuel are mainly designed to reduce deposit formation on intake valves and fuel injectors, but it has been reported that some additives may contribute to CCD formation. Therefore, a standardized bench engine test method for CCDs needs to be developed in response to industry demands. Cooperative research between the Petroleum Association of Japan (PAJ) and the Japan Automobile Manufacturers Association, Inc. (JAMA), has led to the development of a 2.2L Honda engine dynamometer-based CCD test procedure to evaluate CCDs from fuel additives. Ten automobile manufacturers, nine petroleum companies and the Petroleum Energy Center joined the project, which underwent PAJ-JAMA round robin testing. This paper describes the CCD test development activities, which include the selection of an engine and the determination of the optimum test conditions and other test criteria.

Achieving a multi-cylinder engine with excellent noise/vibration character sties and low friction at the main bearings requires an optimal design not only for the crankshaft construction but also for the bearing support system of the cylinder block. To accomplish that, it is necessary to understand crankshaft system behavior and the bearing load distribution for each of the main bearings. Crankshaft system behavior has traditionally been evaluated experimentally because of the difficulty in performing calculations to predict resonance behavior over the entire engine speed range. A coupled crankshaft-block analysis method has been developed to calculate crankshaft system behavior by treating vibration and lubrication in a systematic manner. This method has the feature that the coupled behavior of the crankshaft and the cylinder block is analyzed by means of main bearing lubrication calculations. This paper presents the results obtained with this method.

The authors have proposed a new method to identify the important information which links to the basic principle of the design's physical behavior by using CAE technology, and this method was named as CAP (Computer-Aided Principle).This method can help the engineers to grasp the basic physical characteristic that governs the first-order behavior. In this study, the authors applied CAP to the simulations of the design of frontal crash phenomena, which are difficult to understand because of the problem of strong nonlinearity, and explored the possibilities for using CAP. The correlative physical parameters thus obtained can help designers to understand the essence of the phenomena involved.

The Computer-Aided Principle (CAP) is applied in this study as an effective approach to the crashworthiness design of the vehicle front-end structure. With this method, correlative parameters are extracted in a parametric study by using a cluster analysis. The results can help engineers to understand the fundamental mechanisms of structural phenomena. A simulation example of an offset frontal crash against a deformable barrier (ODB) is presented to show the effectiveness of the proposed method.

With SUVs and minivans accounting for a larger share of the US market in the past decade, rollover accidents have drawn greater attention, leading to more active research from different perspectives. This ranges from investigations for elucidating the basic causes and mechanisms of rollover accidents to studies of more advanced occupant protection measures. As the phenomenon of a rollover accident is longer in duration than frontal, side or rear impacts, it is relatively difficult [1] to simulate such accidents for experimental verification and also for proper evaluation of occupant restraint system performance. In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA.

Most of the side impact air bag systems in the current market are designed to protect the thorax area only. The new Head and Thorax SRS Side Impact Air Bag system, which Nissan recently introduced into the market, was designed to help provide additional protection for the head in certain side impacts. The system may help protect occupant head contacts when the vehicle collides into a tree, or the high hood of a large striking vehicle. This paper introduces the additional features and function of the new Head and Thorax SRS Side Impact Air Bag system, and some evaluation results in laboratory testing.

Recently, it has been very important to reduce the noise, especially the Squeak and Rattle noise, for improving customer appeal of passenger vehicles. The Squeak and Rattle noise occurring inside the car cabin during vehicle operation is an especially large problem. This paper describes a newly developed measurement technology that uses the developed signal processing using the Beam-forming method and vibration sensor to identify the Squeak and Rattle noise sources, making it possible to determine effective countermeasures quickly. This new technology is used to identify all Squeak and Rattle noises at a time among many different noises, for example Wind noise, Engine noise and Road noise occurring during vehicle operation, and is expected to shorten substantially the time needed for noise analysis and contribute to quality improvements.

The probability or risk of traffic accidents must be estimated quantitatively in order to implement effective traffic safety measures. In this study, various statistical data and probability theory were used to examine a method for predicting the risk of crossing-collisions, representing a typical type of accident at intersections in Japan. Crossing-collisions are caused by a variety of factors, including the road geometry and traffic environment at intersections and the awareness and intentions of the drivers of the striking and struck vehicles. Bayes' theorem was applied to find the accident probability of each factor separately. Specifically, the probability of various factors being present at the time of a crossing-collision was estimated on the basis of traffic accident data and observation survey data.

In general, the improvement of vehicle body stiffness involves a trade-off with the body weight. The objective of this research is to derive the lightest-weight solution from the original vehicle model by finding the optimized spot-weld layout and body panel thickness, while keeping the body stiffness and number of spot welds constant. As the first step, a method of deriving the optimal layout of spot welds for maximizing body stiffness was developed by applying the topology optimization method. While this method is generally used in shape optimization of continuous solid structures, it was applied to discontinuous spot-weld positions in this work. As a result, the effect of the spot-weld layout on body stiffness was clarified. In the case of the body used for this research, body stiffness was improved by about 10% with respect to torsion and vertical and lateral bending.

The brake-operated pre-crash seatbelt system retracts the seatbelt webbing by activating an electric motor attached to the seatbelt retractor. Detection of emergency braking is used as a trigger to activate the motor. Retracting the seatbelt helps to reduce an occupant's forward movement due to inertial force acting on the occupant's body during deceleration in braking. Addtionally, retraction of the seatbelt webbing also helps existing occupant restraint devices to work more effectively in a crash. The effectiveness of the pre-crash system was evaluated by considering two conditions combined. One involved the dynamic behavior of the vehicle and occupants prior to a crash. The other concerned the safety performance of the vehicle during the crash event. Experiments were conducted to measure the behavior of the vehicle and occupants under emergency braking prior to a crash.

The accuracy of FE (Finite Element) side impact dummy characteristics is important when using FE vehicle model for vehicle development. This study evaluated the response characteristics of FE SID-lls dummy (5TH female) model that was developed by FTSS using FE code PAM-CRASH™. This paper will describe improvements of computational evaluation method and FE dummy model in the sled tests simulated interior. For the various impact conditions, good correlation between FE calculation and the sled test results was obtained.

The numerical relations between occupant restraint systems and injury indexes were investigated by multi-parameter optimization of an integrated restraint system model of frontal crash simulations. This paper proposes a method of optimizing restraint systems in two types of test configurations: a 35-mph full overlap crash model and a 40-mph 40%-offset crash model.

Eight rollover research tests were conducted using the 2001 Nissan Pathfinder with a modified FMVSS 208 dolly rollover test method where the driver and right front dummy restraint performance was analyzed. The rollover tests were initiated with the vehicle horizontal, not at a roll angle. After the vehicle translated laterally for a short distance, a trip mechanism was introduced to overturn the vehicle. Retractor, buckle, and latch plate performance in addition to the overall seat belt performance was analyzed and evaluated in the rollover test series. Retractor pretensioners were activated near the rollover trip in three of the tests to provide research data on its effects. Various dummy sizes were utilized. The test series experienced incomplete data collection and a portion of the analog data was not obtained. National Automotive Sampling System (NASS) data was also analyzed to quantify the characteristics of real world rollovers and demonstrated the benefits of restraint use.

Eliminating squeal noise generated during braking is an important task for the improvement of vehicle passengers' comfort. Considerable amount of research and development works have been done on the problem to date. In this study, we focused on the analyses of friction self-excited vibration and brake part resonance during high frequency brake squeal. Friction self-excited vibration is caused by the dry friction between pads and rotor, and occurs as a function of their relative sliding velocities. Its vibration frequency can be calculated in relation to the mass and stiffness of the pad sliding surface. Frequency responses of the brake assembly were measured and the vibration modes of the pad, disc and caliper during squeal were identified through modal analysis. Further study led to the development of a computer simulation method for analyzing the vibration modes of brake parts. Analytical results obtained using the method agreed well with the corresponding experimental data.

Recent years have seen remarkable advances in the development and diffusion of numerical analysis techniques using the finite element method for examining vehicle crashworthiness. The importance of numerical analysis in vehicle development work has also increased. One reason for this is that the use of numerical analysis makes it possible to study crash phenomena in detail based on calculated data which can not be obtained experimentally. In this study, the non-linear dynamic finite element program PAM-CRASH was applied to a vehicle frontal crash simulation to calculate the body deformation modes, the force transmitted at different sections of the body structure and the internal energy accumulation of each component. The results obtained provide a quantitative explanation of the deformation mechanism of the body structure.

Evaluations of dummy injury readings obtained in regulatory crash tests and new car assessment program tests provide indices for the development of crash safety performance in the process of developing new vehicles. Based on these indices, vehicle body structures and occupant restraint systems are designed to meet the required occupant injury criteria. There are many types of regulatory tests and new car assessment program tests that are conducted to evaluate vehicle safety performance in side impacts. Factoring all of the multiple test configurations into the development of new vehicles requires advanced design capabilities based on a good understanding of the mechanisms producing dummy injury readings. In recent years, advances in computer-aided engineering (CAE) tools and computer processing power have made it possible to run simulations of occupant restraint systems such as side airbags and seatbelts.

The progress of computer technology and CAE methodology makes it possible to simulate dummy injury readings in vehicle crash simulations. Dummy neck injuries are generally more difficult to simulate than injuries to other regions such as the head or chest. Accordingly, improving the accuracy of dummy neck injury data is a major concern in frontal occupant safety simulations. This paper describes the use of an advanced airbag modeling methodology to improve the accuracy of dummy neck injury readings. First, the following items incorporated in the advanced airbag model are explained. (1) The Finite Point Method (FPM) is used to simulate the flow of gas. (2) A folding model is applied to simulate the folded condition. (3) The fabric material properties used in the simulation take into account anisotropy in the fiber directions and the nonlinear, hysteresis characteristics of stiffness.

Nissan has added ball bearings to its “High-flow Ceramic Turbocharger”(1) (introduced in 1987) to improve acceleration response by reducing friction loss. The following programs were carried out in applying ball bearings to the turbocharger: Optimum bearing size and material were selected to assure long life; lubrication techniques were employed to achieve compatibility between acceleration response and durability; a thrust support system was designed to assure that the ball bearings endure thrust load which varies in direction and magnitude during engine operation; and the squeeze film damper was optimized to keep the turbocharger silent. These innovations have resulted in a practical ball-bearing turbocharger, which has been installed in Nissan's most recent Skyline model(released in May 1989). This is the first time a ball-bearing turbocharger has been applied to a passenger car.

A side impact is one of the severest crash configurations among real-world accidents. In the US market, even though most vehicles have achieved top ratings in crash performance assessment programs in recent years, there has hardly been any sign of a decline in side-impact fatalities for the last few years, according to statistics retrieved from the National Highway Traffic Safety Administration’s Fatality Analysis Reporting System. In response to this trend, the Insurance Institute for Highway Safety (IIHS) is planning to introduce a new test protocol for side impact assessment. One of the points to be clarified in current side impact tests is whether the present side moving deformable barrier (MDB), which includes the barrier face and cart, faithfully reproduces a real-world car-to-car crash.