Search Results

Elastomeric joints are utilized in many automotive applications, and exhibit frequency and excitation amplitude dependent properties. Current methods commonly identify only the cross-point joint property using displacement excitation at stepped single frequencies. This process is often time consuming and is limited to measuring a single dynamic stiffness term of the joint stiffness matrix. This study focuses on developing tractable laboratory inverse experiments to identify frequency dependent stiffness matrices up to 1000 Hz. Direct measurements are performed on a commercial elastomer test system and an inverse experiment consisting of an elastic beam (with a square cross section) attached to a cylindrical elastomeric joint. Sources of error in the inverse methodology are thoroughly examined and explained through simulation which include ill-conditioning of matrices and the sensitivity to modeling error.

Hydraulic bushings with amplitude sensitive and spectrally varying properties are commonly used in automotive suspension. However, scientific investigation of their dynamic properties has been mostly limited to linear system based theory, which cannot capture the significant amplitude dependence exhibited by the devices. This paper extends prior literature by introducing a nonlinear fluid compliance term for reduced-order bushing models. Quasi-linear models developed from step sine tests on an elastomeric test machine can predict amplitude dependence trends, but offer limited insight into the physics of the system. A bench experiment focusing on the compliance parameter isolated from other system properties yields additional understanding and a more precise characterization.

This paper presents a cohesive set of engine-in-the-loop (EIL) studies examining the use of hierarchical model-predictive control for fuel consumption minimization in a class-8 heavy-duty truck intended to be equipped with Level-1 connectivity/automation. This work is motivated by the potential of connected/automated vehicle technologies to reduce fuel consumption in both urban/suburban and highway scenarios. The authors begin by presenting a hierarchical model-predictive control scheme that optimizes multiple chassis and powertrain functionalities for fuel consumption. These functionalities include: vehicle routing, arrival/departure at signalized intersections, speed trajectory optimization, platooning, predictive optimal gear shifting, and engine demand torque shaping. The primary optimization goal is to minimize fuel consumption, but the hierarchical controller explicitly accounts for other key objectives/constraints, including operator comfort and safe inter-vehicle spacing.

There are several geometric and working parameters, besides offset, that have minor effects on hypoid gears efficiency (i.e. spiral angle, pressure angle, lubricant type & temperature, surface finish, etc.). Some theoretical analyses of mechanical efficiency of hypoid gears show that surface finish has considerable effect on hypoid gear efficiency. This is due to a high sliding to rolling ratio in these types of gears. In this paper, a study on measuring of surface finish of both ring gear and pinion will be presented. Moreover, the effects of lapping on surface finish will be discussed. Using an accurate form-measuring machine, surface finish measurements were done on several experimentally produced hypoid gear pairs1. Despite the fact that lapping is expected to improve the surface finish, measurement results show that ring gear's surface finish becomes worse (roughness increased) after lapping while no consistent results for pinion surface finish were observed.

This research focuses on the development and performance of analytical models to simulate a tractor-semitrailer in straight-ahead braking. The simulations were modified and tuned to simulate full-treadle braking with all brakes functioning correctly, as well as the behavior of the tractor-semitrailer rig under full braking with selected brakes disabled. The models were constructed in TruckSim and based on a tractor-semitrailer used in dry braking performance testing. The full-scale vehicle braking research was designed to define limits for engineering estimates on stopping distance when Class 8 air-braked vehicles experience partial degradation of the foundation brake system. In the full scale testing, stops were conducted from 30 mph and 60 mph, with the combination loaded to 80,000 lbs (gross combined weight or GCW), half payload, and with the tractor-semitrailer unladen (lightly loaded vehicle weight, or LLVW).

This paper presents development of a multi-scale material model for a 980 MPa grade transformation induced plasticity (TRIP) steel, subject to a two-step quenching and partitioning heat treatment (QP980), based on integrated computational materials engineering principles (ICME Model). The model combines micro-scale material properties defined by the crystal plasticity theory with the macro-scale mechanical properties, such as flow curves under different loading paths. For an initial microstructure the flow curves of each of the constituent phases (ferrite, austenite, martensite) are computed based on the crystal plasticity theory and the crystal orientation distribution function. Phase properties are then used as an input to a state variable model that computes macro-scale flow curves while accounting for hardening caused by austenite transformation into martensite under different straining paths.

Hybrid electric vehicles (HEV) are essential for reducing fuel consumption and emissions. However, when analyzing different segments of the transportation industry, for example, public transportation or different sizes of delivery trucks and how the HEV are used, it is clear that one powertrain may not be optimal in all situations. Choosing a hybrid powertrain architecture and proper component sizes for different applications is an important task to find the optimal trade-off between fuel economy, drivability, and vehicle cost. However, exploring and evaluating all possible architectures and component sizes is a time-consuming task. A search algorithm, using Gaussian Processes, is proposed that simultaneously explores multiple architecture options, to identify the Pareto-optimal solutions.

Experimental results are presented for a technique of converting Diesel fuel to a gas stream rich in carbon monoxide and hydrogen suitable for Lean NOx Trap (LNT) regeneration. The device is relatively simple and relies upon a premixed, rich flame to generate gas with 4.5% H2 and 10% CO. The device, referred to as a flame reformer, offers a number of advantages over other methods of reductant generation for bypass regeneration LNT systems. Specifically, the device offers rapid dynamic response, potential lower cost, with a similar level of performance to other proposed methods of reductant generation.

The sensitivity factor, λ, of stimulus-response car following equations was computed, based on response times, τ, obtained from aerial survey data. Vehicles of a platoon are investigated as they approach, proceed through, and leave behind a kinematic disturbance, and an inherent local and asymptotic instability is discovered. Aerial survey data is used in a numerical example to demonstrate how multiple rear-end collisions can be triggered by one vehicle. A driver aid system, informing drivers about the differential velocity between lead and following vehicles, could improve stability, although the final answer appears to lie in automated or semi-automated longitudinal control systems.

Two major concerns have inhibited the use of natural laminar flow (NLF) for viscous drag reduction on production aircraft. These are the concerns of achieveability of NLF on practical airframe surfaces, and maintainability in operating environments. Previous research in this area left a mixture of positive and negative conclusions regarding these concerns. While early (pre-1950) airframe construction methods could not achieve NLF criteria for waviness, several modern construction methods (composites for example) can achieve the required smoothness. This paper presents flight experiment data on the achieveability and maintainability of NLF on a high-performance, single-propeller, composite airplane, the Bellanca Skyrocket II. The significant contribution of laminar flow to the performance of this airplane was measured. Observations of laminar flow in the propeller slipstream are discussed, as are the effects of insect contamination on the wing.

This paper describes the modeling, controller development, and implementation of a transmission clutch pressure control system. A nonlinear analytical model for the clutch pressure control system is developed and implemented using Matlab/Simulink, and validated by experimental data. The dominant dynamics are identified via model analysis, and a linear model is derived for controller design. Openloop (feedforward) and closed loop (feedback) pressure control strategies are designed and implemented in a test setup. Experimental results show that the combined feedforward and feedback control gives superior performance as compared to feedforward control alone.

A significant number of formed parts constitute the components of an automobile or aircraft. The formed blanks for the components are produced at different temperatures ranging from room temperature to 2250 degrees Fahrenheit for steel. Forming progressions convert a basic shape or geometry (a cylindrical billet, for example) of metal into a more complex shape close to the required final component geometry. The progression steps, choice of temperatures and equipment significantly impact the cost of the blank. A ‘Discriminating Cost Model’ was developed to capture the cost effectiveness of a given choice of process or equipment, and an AI (Artificial Intelligence) search algorithm implemented to quickly search through the large number of process and equipment selection options to arrive at the most cost effective choice. Two applications of this methodology to existing plant processes to significantly reduce cost and implement ‘lean’ principles of manufacturing are discussed.

In recent years, there has been increasing research on automated driving technology. Autonomous vehicle path following performance is one of significant consideration. This paper presents discrete time design of robust PD controlled system with disturbance observer (DOB) and communication disturbance observer (CDOB) compensation to enhance autonomous vehicle path following performance. Although always implemented on digital devices, DOB and CDOB structure are usually designed in continuous time in the literature and also in our previous work. However, it requires high sampling rate for continuous-time design block diagram to automatically convert to corresponding discrete-time controller using rapid controller prototyping systems. In this paper, direct discrete time design is carried out. Digital PD feedback controller is designed based on the nominal plant using the proposed parameter space approach.

Edge fracture is a common problem when forming advanced high strength steels (AHSS). A particular case of edge fracture occurs during a collar forming/hole extrusion process, which is widely used in the sheet metal forming industry. This study attempts to relate the edge stretchability in collar forming to the strain hardening along the pierced edge; thus, Finite Element (FE) simulations can be used to reduce the number of experiments required to improve cutting settings for a given material and thickness. Using a complex-phase steel, CP-W 800 with thickness of 4.0 mm, a single-stage piercing operation is compared with a two-stage piercing operation, so called shaving, in terms of strains along the pierced edge, calculated by FE simulation. Results indicated that strains were reduced along the pierced edge by shaving.

Automobile manufacturers are reducing the weight of their vehicles in order to meet strict fuel economy legislation. To achieve this goal, a combination of different materials such as steel, aluminum and carbon fiber composites are being considered for use in vehicle bodies. The ability to join these different materials is an ongoing challenge and an area of research for automobile manufacturers. Multiridged fasteners are a viable option for this type of multi-material joining. Commercial systems exist and are being used in the industry, however, new ridged nail designs offer the potential for improvement in several areas. The goal of this paper is to prototype and test a safer flat-end fastener whilst not compromising on strength characteristics, to prevent injury to factory workers. The nails were prototyped using existing RIVTAC® nails.

Vaporizing Foil Actuators (VFA) are based on the phenomenon of rapid vaporization of thin metallic foils and wires, caused by passage of a capacitor bank driven current on the order of 100 kA. The burst of the conductor is accompanied with a high-pressure pulse, which can be used for working metal at high strain rates. This paper focuses on the use of VFA for collision welding of dissimilar metals, in particular, aluminum and steel. Aluminum alloy 6061 sheets of 1 mm thickness were launched to velocities in excess of 650 m/s with input electrical energy of 8 kJ into 0.0762 mm thick, dog-bone shaped aluminum foil actuators. Target sheets made from dual phase steel (DP780) were impacted with the aluminum flyer sheet, and solid state impact welds were created. During mechanical testing, many samples failed outside the weld area, thereby indicating that the weld was stronger than the parent aluminum.

This paper and the associated lecture present an overview of technology trends and of market and business opportunities created by technology, as well as of the challenges posed by environmental and economic considerations. Commercial vehicles are one of the engines of our economy. Moving goods and people efficiently and economically is a key to continued industrial development and to strong employment. Trucks are responsible for nearly 70% of the movement of goods in the USA (by value) and represent approximately 300 billion of the 3.21 trillion annual vehicle miles travelled by all vehicles in the USA while public transit enables mobility and access to jobs for millions of people, with over 10 billion trips annually in the USA creating and sustaining employment opportunities.

The parameters determining shift quality control in automatic transmissions are determined as part of the calibration of the transmission control. The resulting control system typically has three components: feedforward control, where the control output is determined before a gearshift; feedback control, where the control output is determined during the gearshift based on sensed feedback; and learning control (adaptation), where the feedforward or feedback controller parameters are modified after the current gearshift has ended and before the next similar gearshift begins. Gearshifts involving the same ratio change are referred to here as similar gearshifts, though such gearshifts may involve differences in other variables such as vehicle speed or engine torque.

The objective is to determine whether responses and injury risks for pediatric occupants in child restraint systems (CRS) are affected by vehicle seat cushion stiffness and fore/aft cushion length. Eighteen sled tests were conducted using the Federal Motor Vehicles Safety Standard (FMVSS) 213 frontal pulse (48 km/h). Seats from a recent model year vehicle were customized by the manufacturer with three different levels of cushion stiffness: compliant, mid-range, and stiff. Each stiffness level was quantified using ASTM D 3574-08 and all were within the realistic range of modern production seats. The usable length of each seat cushion was manipulated using foam spacers provided by the manufacturer. Two different seat lengths were examined: short (34.0 cm) and long (43.5 cm).

In the last decade, the accelerated advancements in manufacturing techniques and material science enabled the automotive industry to manufacture commercial vehicles at more affordable rates. This, however, brought about roadways having to accommodate an ever-increasing number of vehicles every day. However, some roadways, during specific hours of the day, had already been on the brink of reaching their capacity to withstand the number of vehicles travelling on them. Hence, overcrowded roadways create slow traffic, and sometimes, bottlenecks. In this paper, a Dynamic Speed Harmonization (DSH) algorithm that regulates the speed of a vehicle to prevent it from being affected by bottlenecks has been presented. First, co-simulations were run between MATLAB Simulink and CarSim to test different deceleration profiles.