Search Results

The current trend towards an increasing electrification of road vehicles brings to life a whole series of unprecedent design issues. Among these, the ageing process that affects the lifetime of lithium-ion based energy storage systems is of particular importance since it turns out to be extremely sensitive to the variation of battery operating conditions normally occurring especially in hybrid electric vehicles (HEVs). This paper aims at analyzing the impact of operating conditions on the predicted lifetime of a parallel-through-the-road plug-in HEV battery both from thermal and ageing perspectives. The retained HEV powertrain architecture is presented first and modeled, and the related energy management system is implemented. Dedicated numerical models are also discussed for the high-voltage battery pack that allow predicting its thermal behavior and cyclic ageing.

The use of Ducted Fuel Injection (DFI) for attenuating soot formation throughout mixing-controlled diesel combustion has been demonstrated impressively effective both experimentally and numerically. However, the last research studies have highlighted the need for tailored engine calibration and duct geometry optimization for the full exploitation of the technology potential. Nevertheless, the research gap on the response of DFI combustion to the main engine operating parameters has still to be fully covered. Previous research analysis has been focused on numerical soot-targeted duct geometry optimization in constant-volume vessel conditions. Starting from the optimized duct design, the herein study aims to analyze the influence of several engine operating parameters (i.e. rail pressure, air density, oxygen concentration) on DFI combustion, having free spray results as a reference.

The paper has the aim of assessing and applying control-oriented models capable of predicting HRR (Heat Release Rate) and MFB50 in DI diesel engines. To accomplish this, an existing combustion model, previously developed by the authors and based on the accumulated fuel mass approach, has been modified to enhance its physical background, and then calibrated and validated on a GM 1.6 L Euro 6 DI diesel engine. It has been verified that the accumulated fuel mass approach is capable of accurately simulating medium-low load operating conditions characterized by a dominant premixed combustion phase, while it resulted to be less accurate at higher loads. In the latter case, the prediction of the heat release has been enhanced by including an additional term, proportional to the fuel injection rate, in the model. The already existing and the enhanced combustion models have been calibrated on the basis of experimental tests carried out on a dynamic test bench at GMPT-E.

Tire inflation pressure has a relevant impact on fuel consumption and tire wear, and therefore affects both CO2 emissions and the total cost of ownership (TCO). The latter is extremely important in the case of commercial vehicles, where the cost of fuel is responsible for about 30% of the TCO. A possible advanced central tire inflation system, which is able to inflate and deflate tires autonomously, as part of a smart energy management system and as an active safety device, has been studied. This system allows misuse due to underinflation to be avoided and adapts the tires to the current working conditions of the vehicle. For instance, the tire pressure can be adapted according to the carried load or during tire warm-up. An on board software is able to evaluate the working conditions of the vehicle and select the tire pressure that minimizes the energy expense, the TCO, or the braking distance, according to a multi-objective optimization strategy.

Active tire pressure control (ATPC) is an automatic central tire inflation system (CTIS), designed, prototyped, and tested at the Politecnico di Torino, which is aimed at improving the fuel consumption, safety, and drivability of passenger vehicles. The pneumatic layout of the system and the designed solution for on board integration are presented. The critical design choices are explained in detail and supported by experimental evidence. In particular, the results of experimental tests, including the characterizations of various pneumatic components in working conditions, have been exploited to obtain a design, which allows reliable performance of the system in a lightweight solution. The complete system has been tested to verify its dynamics, in terms of actuation time needed to obtain a desired pressure variation, starting from the current tire pressure, and to validate the design.

A method for estimating the sideslip angle of a Formula SAE vehicle with torque vectoring is presented. Torque vectoring introduces large tire longitudinal forces which lead to a reduction of the tire lateral forces. A novel tire model is utilized to represent this reduction of the lateral forces. The estimation is realized using an extended Kalman filter which takes in standard sensor measurements. The developed algorithm is tested by simulating slalom and figure eight maneuvers on a validated VI-CarRealTime vehicle model. Results indicate that the algorithm is able to estimate the sideslip angle of the vehicle reliably on a high friction surface track.

As an era of autonomous driving approaches, it is necessary to translate handling comfort - currently a responsibility of human drivers - to a vehicle imbedded algorithm. Therefore, it is imperative to understand the relationship between perceived driving comfort and human driving behaviour. This paper develops a methodology able to generate the information necessary to study how this relationship is expressed in highway overtakes. To achieve this goal, the approach revolved around the implementation of sensor Data Fusion, by processing data from CAN, camera and LIDAR from experimental tests. A myriad of variables was available, requiring individuating the key-information and parameters for recognition, classification and understanding of the manoeuvres. The paper presents the methodology and the role each sensor plays, by expanding on three main steps: Data segregation and parameter selection; Manoeuvre detection and processing; Manoeuvre classification and database generation.

This paper presents a study related to an Articulated Amphibious All-Terrain Tracked Vehicle (ATV) characterized by a modular architecture. The ATV is composed by two modules: the first one hosts mainly the vehicle engine and powertrain components, meanwhile the second one can be used for goods transportation, personnel carrier, crane and so on. The engine torque is transmitted to the front axle sprocket wheel of each module and finally distributed on the ground through a track mechanism. The two modules are connected through a multiaxial joint designed to guarantee four relative degrees of freedom. To steer the ATV, an Electro Hydraulic Power System (EHPS) is adopted, thus letting the vehicle steerable on any kind of terrain without a differential tracks speed. The paper aims to analyze the steady-state lateral behavior of the ATV on a flat road, through a non-linear mathematical vehicle model built in Matlab/Simulink environment.

In this study, a new EGR control technique, based on the estimate of the oxygen concentration in the intake manifold, was firstly investigated through numerical simulation and then experimentally tested, both under steady state and transient conditions. The robustness of the new control technique was also tested and compared with that of the conventional EGR control technique by means of both numerical simulation and experimental tests. Substantial reductions of the NOx emissions under transient operating conditions were achieved, and useful knowledge for controlling the EGR flow rate more accurately was obtained.

Different EGR system layouts (a Long Route, a Short Route, and a combination of the two) were evaluated by means of both numerical simulation and experimental tests. In particular, a one-dimensional fluid-dynamic engine model was built in order to evaluate the potential of a Long Route EGR system as well as the potential of different EGR combinations between Long and Short Route. By means of the one-dimensional model, used as a virtual test bench, the estimations of the NOx emissions, based on the Extended Zeldovich Mechanism (EZM), for the different solutions, were compared and valuable information for the calibration of the coordinated EGR LR, EGR SR and Variable Geometry Turbine (VGT) control systems was obtained.

The fuel injection plays a crucial role in determining the mixture formation process in Gasoline Direct Injection (GDI) engines. Pollutant emissions, and soot emissions in particular, as well as phenomena affecting engine reliability, such as oil dilution and injector coking, are deeply influenced by the injection system features, such as injector geometric characteristics (such as injector type, injector position and targeting within the combustion chamber) and operating characteristics (such as injection pressure, injection phasing, etc.). In this paper, a new CFD methodology is presented, allowing a preliminary assessment of the mixture formation quality in terms of expected soot emissions, oil dilution and injector coking risks for different injection systems (such as for instance multihole or swirl injectors) and different injection strategies, from the early stages of a new engine design.

Development trends in modern common rail fuel injection systems (FIS) show dramatically increasing capabilities in terms of optimization of the fuel injection strategy through a constantly increasing number of injection events per engine cycle as well as through the modulation and shaping of the injection rate. In order to fully exploit the potential of the abovementioned fuel injection strategy optimization, numerical simulation can play a fundamental role by allowing the creation of a kind of a virtual test rig, where the input is the fuel injection rate and the optimization targets are the combustion outputs, such as the burn rate, the pollutant emissions, and the combustion noise (CN).

Active Roll Control (ARC) is one of the most promising active systems to improve vehicle comfort and handling. This paper describes the simulation based procedure adopted to conceive a double-channel Active Roll Control system, characterized by the hydraulic actuation of the stabilizer bars of a sedan. The first part of the paper presents the vehicle model adopted for this activity. It is Base Model Simulator (BMS), the 14 Degrees-of-Freedom vehicle model by Politecnico di Torino. It was validated through road tests. Then the paper describes the development of the control algorithm adopted to improve the roll dynamics of the vehicle. The implemented control algorithm is characterized by a first subsystem, capable of obtaining the desired values of body roll angle as a function of lateral acceleration during semi-stationary maneuvers.

Different diagnostic techniques were experimentally tested on a common rail automotive 4 cylinder diesel engine in order to evaluate their capabilities to fulfill the California Air Resources Board (CARB) requirements concerning the monitoring of fuel injected quantity and timing. First, a comprehensive investigation on the sensitivity of pollutant emissions to fuel injection quantity and timing variations was carried out over 9 different engine operating points, representative of the FTP75 driving cycle: fuel injected quantity and injection timing were varied on a single cylinder at a time, until OBD thresholds were exceeded, while monitoring engine emissions, in-cylinder pressures and instantaneous crankshaft revolution speed.

Antilock Braking System (ABS) is designed to prevent wheels from locking, in order to enhance vehicle directional stability during braking manoeuvres. Basically, ABS closed-loop control logic uses tyres slip as control variable. Slip is estimated by comparing vehicle reference speed with the angular speed of each wheel. Thus it is crucial to correctly estimate the longitudinal vehicle speed, in order to get a control system capable of good performance. The control is also affected by road condition; since vehicles are not equipped with sensors able to measure the tyre/road friction coefficient, an other estimation has to be performed. The paper presents an algorithm for the estimation of longitudinal speed, based on the measurements of the four wheel angular speed. A method to assess the road friction, commonly known as “learning phase” is also described: it is carried out during the early stage of the active control intervention and relies on the wheel rotation sensors as well.

This paper deals with the development of a Lap Time Simulator in order to carry out a first approximate evaluation of the potential benefits related to the adoption of the Kinetic Energy Recovery System (KERS). KERS will be introduced in the 2009 Formula 1 Season. This system will be able to store energy during braking and then use it in order to supply an extra acceleration during traction. Different technologies (e.g. electrical, hydraulic and mechanical) could be applied in order to achieve this target. The lap time simulator developed by the authors permits to investigate the advantages both in terms of fuel consumption reduction and the improvement of the lap time.

Electric scooters are suited to mobility in zones with environmental traffic limitations, and particularly for city centers with very poor room for parking. Aim of this paper is the illustration of the performance that can be obtained from a purposely designed electric scooter. The features of the main components of the scooter driveline: battery package, converter, motor and control will be described.

Numerical simulation can be effectively used to reduce the experimental tests which are nowadays required for the analysis and calibration of engine control systems. In particular in this paper the use of a one-dimensional engine model to analyze the response of an UEGO sensor in the exhaust manifold of a 4 cylinder s.i. engine (with multipoint fuel injection) is described: numerical simulation has been used to simulate a misfunction of the fuelling system, which caused one of the four cylinders to be fuelled with an air/fuel ratio that was 10% richer than the others. The simulated UEGO response was then compared with experimental measurements, and after this validation process, the sensor model can be used to study a proper fuel injection control strategy thus reducing the required experimental tests, as outlined in a test case presented at the end of the paper.

This paper presents a multi-physic modeling of an electromechanical energy scavenging device able to supply energy inside car tires for wireless sensors. A permanent magnet, connected to the inner liner of a tire, is accelerated along a guide by the tire deformation during car motion; by interacting with coils it generates a power which is conditioned by a proper electronic interfaced to an external load. The original approach implemented in this kind of device is the nonlinear dynamic properties designed and controlled: adaptive resonance in function of car velocity is optimized for increasing its global efficiency. The energy conversion process takes into account the simulation of different phenomena such as: non linear dynamic and adaptive resonant behavior of the seismic mass, electromagnetic and magneto-static coupling between moving mass and coils, transfer of the generated power to an external load by means of a nonlinear circuit interface.

To comply with Stage IV emission standard for off-road engines, Kohler Engines has developed the 100kW rated KDI 3.4 liters diesel engine, equipped with DOC and SCR. Based on this engine, a research project in collaboration between Kohler Engines, Ricardo, Denso and Politecnico di Torino was carried out to exploit the potential of new technologies to meet the Stage IV and beyond emission standards. The prototype engine was equipped with a low pressure cooled EGR system, two stage turbocharger, high pressure fuel injection system capable of very high injection pressure and DOC+DPF aftertreatment system. Since the Stage IV emission standard sets a 0.4 g/kWh NOx limit for the steady state test cycle (NRSC), that includes full load operating conditions, the engine must be operated with very high EGR rates (above 30%) at very high load.