Search Results

There is concern over water-in-oil emulsion formation in passenger cars in the field. Crankcase pressure measurements in the ASTM Sequence IID rust test have been used to indicate possible emulsion formation tendencies of lubricants. This paper presents the development of a short duration emulsion fleet test procedure which demonstrates low car-to- car variability and correlates well with a previous fourmonth winter emulsion fleet test. Physical emulsion characteristics and used oil analyses are described. Evaluation of both Sequence IID reference oils and commercial oils in this field test reveals a lack of correlation between Sequence IID crankcase pressure results and field performance. The new procedure has been applied to investigate the impact of additive and base oil variations on the emulsion-forming tendencies of lubricants in the field. Base oil variables such as viscosity grade, composition, and volatility were evaluated.

Our basic understanding of the chemical and physical nature of soot, its interaction with lubricant components and its role in promoting wear and oil thickening in heavy duty diesel engines continues to grow. Our current study in the GM 6.5L engine focuses on examining the effects of variations in base stock type (Group I vs. Group II), viscosity index improver or viscosity modifier (VM) chemistry (OCP vs. dispersant OCP), zinc dithiophosphate (ZDP) type and dispersant type (low MW vs. high MW) on roller follower wear, viscosity growth and other measured responses. In this study, more robust fluids were tested producing very low wear results and minimal viscosity increase of the lubricant. Fluids containing dispersant OCP (DOCP) and high MW dispersant produced a lower degree of wear, whereas varying the ZDP type (1° vs. 2°) showed no effect on wear. The use of Group II base stocks was associated with significantly lower viscosity increases.

Interactions between automatic transmission fluid (ATF) components and composite friction materials and their effect on friction system performance continues to be an active area of interest to the automotive industry. A more fundamental understanding is needed of how base fluids, ATF additives, friction materials, and transmission design interact to produce the observed transmission system performance and durability. We herein report results from investigations carried out using a relatively thermo-oxidatively stable polyalphaolefin (PAO) base fluid treated with components representative of several additive types we previously reported to have significant negative effects on frictional performance. Secondly, we investigated a conventionally refined 150 N base oil treated with a calcium sulfonate detergent previously shown to improve friction performance.

The lubricant is a key component in the successful operation of a manual transmission, but it is important that the interactive effects with the friction material are understood. This paper examines the effect of several key additive components on the friction and wear performance of a single sinter composition in a carefully controlled laboratory test. In addition, the test method allows one to develop information about the shift behavior of the fluid-synchronizer material combination which provides useful information about shift quality. From the original experimental design program a predictive model was developed and an optimized formulation was tested as a validation of the results.

Extended drain of axle and transmission lubricants has gained wide acceptance in both passenger car and commercial vehicle applications. Understanding how the lubricant changes during extended drain operations is crucial in determining appropriate lubricants and drain intervals for these applications. A suitable aging screen test with an established relationship to field performance is essential. Over the years numerous methods have been studied (DKA, GFC, ISOT, ASTM L-60) with varying degrees of success1,2,3. Current methods tend to be overly severe in comparison to field experience, hence the need for further work in this area. As a result of recent work, a lubricant aging test method has been developed which shows good correlation with field experience, giving us an effective tool in the development of long drain oils.

The use of a copper diesel fuel additive in an emission control system improves particulate oxidation. This expands the operability of available systems by reducing the particulate mass loading and related external energy consumption required during regeneration. Easier, more frequent regenerations improve overall engine/system efficiency and reduce thermal stress on filtration media. Procedures for optimizing additive use are presented. In addition, the results from a health study are reviewed.

This paper describes the development of a image analysis system that can be used to rate injectors from the Cummins L10 Injector Depositing Test. In the procedure, injectors are mounted on a computer controlled turntable and scanned using a CCD camera focused on the labyrinth flow area of the injector. The scanned monochrome images are processed and assigned an average gray scale rating. Results from the image analysis system are compared to the modified CRC Piston and Ring Rating method currently used within the Cummins test procedure. To do this, a series of injectors that have been rated by trained raters at a recent workshop were also rated via the image analysis system. The image analysis system ratings demonstrated a strong correlation (R = 0.85) to the CRC ratings. Using these same injectors, the image analysis method shows improvements in repeatability and reproducibility of approximately 50% over the current procedure.

The regenerative characteristics of a diesel particulate filter have been experimentally examined. The effect of particulate accumulation on system backpressure was of primary interest. To improve particulate regeneration, a copper compound was added to the fuel. The test results demonstrate that copper-containing fuel additives improve the regeneration characteristics of the filter, maintaining system backpressure at an acceptable level. Improved regeneration performance is expected to extend the operating range and life of the filter system. A model describing regeneration characteristics was developed to indicate the benefits of fuel copper concentration in controlling system backpressure.

Interactions between a Zinc dialkyldithiophosphate (ZDP) and three different commercially available succinimide dispersants were observed through changes in solutions behavior, as determined by viscometry and Fourier Transform Infrared spectroscopy (FTIR), and four-ball tests. The viscometric response observed for two component blends of ZDP and succinimide dispersant in white oil changed as a function of the molar Zn to N ratio, indicative of specific interactions. The break in the viscometric response curve occurred at Zn:N=0.13 for all three succinimide dispersants. FTIR spectra of the same ZDP-dispersant blends were examined and similar Zn:N dependencies were observed. Four-ball tests measuring wear scar diameter, seizure load and weld load showed a dependence on the Zn to N ratio similar to that observed by viscometry. At very low Zn to N ratios wear and seizure load were decreased, while at higher ratios the seizure and weld loads were increased over that for ZDP alone.

Piston ring land deposit formation is a key performance criterion in the ASTM Sequence IIIE engine test. Because engine testing of lubricant formulation variables is expensive, a ring land deposit bench test was developed replicating the Sequence IIIE bulk oxidation and deposit formation mechanisms. Following an initial bulk oxidation of the candidate oils, deposits similar in chemical composition and morphology to Sequence IIIE ring land deposits are produced in a modified panel coker apparatus. Good correlation with the ASTM Sequence IIIE engine test has been established. Lubricant additive and base oil effects on oxidation control and deposit formation have been investigated. Their influences on lubricant formulation strategy are discussed.

A test was developed by the Cummins Engine Company to evaluate Diesel fuel quality and potential additive effects. This test utilizes a Cummins L10 Diesel engine with a PT fuel system and stepped plunger injectors. A modified CRC rating system is used to quantify deposit levels. This paper further investigates the L10 Injector Depositing Test and will focus on Diesel fuel and additive variables. In the original work, the bulk of the data was collected on an industry standard reference fuel, Cat 1-H, as opposed to commercially available Diesel fuels. Commercially available Diesel fuel varies in composition with regard to sulfur level, percent aromatics, final distillation end point, and cetane number. To evaluate these fuel properties and their possible effects on injector deposit formation, two test matrices were designed. The first experiment is a 12-run fractional factorial design with four factors: additive level, sulfur, aromatics, and 90 percent distillation point (T90).

A test method has been developed which provides for the rapid measurement of the scuffing performance of diesel fuel using the Ball-On-Cylinder Lubricity Evaluator (BOCLE). A test can be completed in less than one hour. Data has been generated indicating that the method achieves good discrimination between fuels of varying lubricity and correlates well with fuel performance as measured in pump tests.

Viscosity Modifiers (VM's) are commonly sold as polymer in oil concentrates. Thus, the handling (pumpability and mixability) characteristics of these systems are important practical considerations. These VM's normally are characterized only by kinematic viscosity, although they are handled at a range of shear rates/stresses which kinematic viscosity does not describe. New polymer types and structures and the desire to make the modifier level as high as possible requires more than a single point kinematic viscosity measurement. The rheological behavior of the concentrate is required to make economical systems that can be handled in a practical manner. This paper represents an initial study of viscosity modifier concentrates by rheological techniques.

Accurate, timely field test results are necessary to develop and validate lubricants meeting frequently changing performance requirements. Field tests can also provide valuable information about performance deficiencies (e.g., soot related wear) which are not apparent in laboratory development tests. Since field tests are time intensive and increasingly expensive, it is imperative that the data generated provide meaningful results with reasonable expenditures. The data generation and analysis process are being constantly improved according to the principles of quality management. Part of the process improvement focuses on accurate, realistic treatment of the data since more variation is typically observed in field tests than in laboratory tests. One of the most difficult analytical processes occurs with oil consumption data.

The International Lubricant Standardization and Approval Committee (ILSAC) GF-2 requirements for Passenger Car Motor Oils (PCMOs) will lower phosphorus limits from a maximum of 0.12% allowed by ILSAC GF-1 to a maximum of 0.10%. In effect, the ILSAC GF-2 phosphorus limit removes 17% of the most commonly used antiwear and antioxidant additive in current PCMOs, zinc dialkyldithiophosphate (ZDP). This paper outlines some work in ASTM Sequence V engine dynamometer tests to quantify the effect of reducing the ZDP on valve train wear and sludge formation. Engine data for the Sequence VE, the proposed Sequence VF, and the modified Sequence VE are presented. These three tests summarize the evolution of the Sequence V from the Sequence VE for GF-1 to the dual plug Sequence VE configuration for the GF-2 specification.

Intentionally adding water to oil, in the laboratory, provides an indication of the oil's ability to tolerate the presence of water. Various characteristics, such as emulsion, haze or separation, may be observed. Some blends of oil and water have been shown to form structures when left undisturbed. A visual, qualitative, storage test is capable of detecting this phenomenon as the presence or absence of structure. However, the time frame of formation can be on the order of days or weeks and is sensitive to handling and temperature effects. Quantitative methods are required for any evaluation of chemistry, temperature and handling effects on the rate and strength of structure formation. This paper describes rheological and electrical methods which directly and indirectly measure the tendency to form a structure at the molecular level, yielding rate of formation and strength information.

Despite the many years of widespread use of the BMW Intake Valve Deposit (IVD) vehicle test, relatively little has been published quantifying the variation in the test procedure. This paper presents an analysis of the variability in the BMW test. Though results from 8045 km (8K; 5,000 mile) tests rather than 16090 km (16K; 10,000 mile) are highlighted due to the size of the available database and relative sensitivity of the data, analysis suggests that variation at 8K is representative of 16K variation. A square root transformation of average deposit weight at 8K, though more cumbersome than the more common log transformation, is found to be the most appropriate way to eliminate the dependence of variation on the absolute level of deposits. Within-car variation is found to account for over half of the test-to-test variation, contradicting the notion that car-to-car differences are the dominant source of variability.

Information relative to oil thickening has been developed in road tests. Typical operating temperatures, as well as the length of time required to thicken oils in these tests, are described. A laboratory test procedure has been developed that shows a good degree of correlation with this field service. The effect of test conditions such as jacket temperature and piston ring design on oil thickening in the laboratory are described.

Additives are an integral part of today's fuels. Together with carefully formulated base fuel composition, they contribute to efficiency, dependability and long life of gasoline and diesel engines. As a primer, this paper describes the range of chemical additives formulated for gasoline and diesel fuel and their effects. Specific functions and benefits of additives, typical use levels, and test methods for evaluation are discussed. Additive usage may be divided into three major categories: a) to satisfy desired levels of performance in engines, b) to insure delivery of uncontaminated, on-specification fuels to the end user and c) achieve necessary chemical/physical properties as manufactured by the refiner.