Search Results

The advantages of gasoline direct-injection are intake air cooling due to fuel vaporization which reduces knocking, additional degrees of freedom in designing a stratified injection mixture, and capability for retarded ignition timing which shortens catalyst light-off time. Stratified mixture combustion designs often require complicated piston shapes which disturb the fluid flow in the cylinder, leading to power reduction, especially in turbocharged gasoline direct-injection engines. Our research replaced the conventional shell-type shallow cavity piston with a dog dish-type curved piston that includes a small lip to facilitate stratification and minimize flow disturbance. As a result, stable stratified combustion and increased power were both achieved.

This paper analyzes low-speed pre-ignition (LSPI), a sudden pre-ignition phenomenon that occurs in downsized boosted gasoline engines in low engine speed high-load operation regions. This research visualized the in-cylinder state before the start of LSPI combustion and observed the behavior of particles, which are thought to be the ignition source. The research also analyzed pre-ignition by injecting deposit flakes and other combustible particulate substances into the combustion chamber. The analysis found that these particles require at least two combustion cycles to reach a glowing state that forms an ignition source. As a result, deposits peeling from combustion chamber walls were identified as a new mechanism causing pre-ignition. Additionally, results also suggested that the well-known phenomenon in which the LSPI frequency rises in accordance with greater oil dilution may also be explained by an increase in deposit generation.

This paper presents the effects of a lubricant oil droplet on the start of combustion of a fuel-air mixture. Lubricant oil is thought to be a major source of low-speed pre-ignition in highly boosted spark ignition engines. However, the phenomenon has not yet been fully understood because its unpredictability and the complexity of the mixture in the engine cylinder make analysis difficult. In this study, a single oil droplet in a combustion cylinder was considered as a means of simplifying the phenomenon. The conditions under which a single oil droplet ignites earlier than the fuel-air mixture were investigated. Tests were conducted by using a rapid compression expansion machine. A single oil droplet was introduced into the cylinder through an injector developed for this study. The ignition and the flame propagation were observed through an optical window, using a high-speed video camera.

ExxonMobil, Corning and Toyota have collaborated on an Onboard Separation System (OBS) to improve gasoline engine efficiency and performance. OBS is a membrane based process that separates gasoline into higher and lower octane fractions, allowing optimal use of fuel components based on engine requirements. The novel polymer-ceramic composite monolith membrane has been demonstrated to be stable to E10 gasoline, while typically providing 20% yield of ∼100 RON product when using RUL 92 RON gasoline. The OBS system makes use of wasted exhaust energy to effect the fuel separation and provides a simple and reliable means for managing the separated fuels that has been demonstrated using several generations of dual fuel test vehicles. Potential applications include downsizing to increase fuel economy by ∼10% while maintaining performance, and with turbocharging to improve knock resistance.

Turbocharged (TC) engines have been introduced these days to improve the fuel economy. It is considered that one possible issue of the TC engine is a pre-ignition at high engine speed because of high temperature and high pressure in the combustion chamber. This study shows the effect of fuel compounds on pre-ignition at 4400rpm. The experimental engine is a naturally-aspirated (NA) engine which is customized to imitate the cylinder temperature and pressure of TC engines. It is known that research octane number (RON) describes anti-knock quality well. Meanwhile the results show that pre-ignition characteristic at high engine speed is dominated by motor octane number (MON) and auto-ignition temperature (AIT) rather than RON.

To avoid knocking phenomena, a special crank mechanism for gasoline engine that allowed the piston to move rapidly near TDC (Top Dead Center) was developed and experimentally demonstrated in the previous study. As a result, knocking was successfully mitigated and indicated thermal efficiency was improved [1],[2],[3],[4]. However, performance of the proposed system was evaluated at only limited operating conditions. In the present study, to investigate the effect of piston movement near TDC on combustion characteristics and indicated thermal efficiency and to clarify the knock mitigation mechanism of the proposed method, experimental studies were carried out using a single cylinder engine with a compression ratio of 13.7 at various engine speeds and loads. The special crank mechanism, which allows piston to move rapidly near TDC developed in the previous study, was applied to the test engine with some modification of tooling accuracy.

This paper describes a new 2.4-liter 16-valve in-line four-cylinder engine, 2TZ-FE, which has been mounted horizontally on a new minivan, the TOYOTA PREVIA. This engine has the TOYOTA original compact 4-valve DOHC system (scissors gear mechanism), and TOYOTA's newest technologies, such as 75 deg. slant cylinder and Separated accessory Drive System. The compact configuration reduces the height of this engine to only 44Omm (17.3-inches). Engine location is under the flat floor on the midship rear-wheel-drive vehicle and allows the PREVIA to have a spacious cabin with walkthrough. Its high performance, 103kW at 500Orpm and 209Nm at 4000rpm, has been achieved through updated technologies, such as: Knock Controll System (KCS), well studied intake system and exhaust manifold which is made of stainless steel double pipe. At the same time, high reliability and quietness have been achieved for the 2TZ-FE by TOYOTA's updated technologies.

The higher compression ratio engines, two-stroke engines and flexible fuel vehicles currently under development tend to face the problems of spark plug fouling owing to the necessity of using cold type spark plugs. This paper analyzes the sparking of fouled spark plugs and investigates the characteristics required of an ignition system in order to avoid fouling problems. The results clearly establish that to maintain a strong spark even when the plug is fouled, a high voltage should be instantaneously applied to the spark plug. A series-gap on the high-tension side was confirmed to be an effective means of achieving this and a new plug cap provided with a series-gap has resolved fouling problems such as failure to start. Lately, fuel economy and long-term energy conservation have become critically important. For automobiles, higher compression ratio engines, two-stroke engines and flexible fuel vehicles (FFVs) are being developed.

For a vehicle fatigue and strength testing system, two methods are usually used to accurately simulate the road-load on the test bench: one is the “separation of road-load into multi-axial loads” method and the other is the “compensation with frequency response function” method. These methods have remarkably improved the abnormality detection capability and accuracy of bench testing. For power steering or other units, however, the road-load points drift while the vehicle is driven. Further more, the road-load is applied in a complex manner to the vehicle. These factors make it difficult to separate the road-load into multi-axial loads and to provide stable measurement of the frequency response function. Thus, further progress of these methods has been delayed. The objective of this study was to make the bench testing of power steering units possible.

For a Knock Control System (KCS) with a vibration sensor mounted on the engine block, means of improving the ratio of knock signal to engine vibration noise are discussed. From analyses of cylinder pressure and engine block vibration spectrums, it is shown that noise is lower in the second knock resonance frequency. The development of a resonance type knock sensor detecting this higher frequency is described. A new KCS utilizing this sensor is evaluated and found to improve knock controllability, especially in engines with a high compression ratio or supercharging.

Gasoline engine downsizing combined with a turbocharger is one of the more effective approaches to improve fuel efficiency without sacrificing power performance. The benefit comes from lower pumping loss, lower mechanical friction due to ‘downsizing’ of the engine displacement and ‘down-speeding’ of the engine by using higher transmission gear ratios which is allowed by the higher engine torque at lower engine speeds. However abnormal combustion referred to as Low-Speed Pre-ignition (LSPI) is known to be able to occur in low-speed and high-torque conditions. It is a potential restriction to maximize the engine performance and its benefit, therefore prevention of LSPI is strongly desired for long-term durability of engine performance. According to recent technical reports, auto-ignition of an engine oil droplet in a combustion chamber is believed to be one of major contributing factors of LSPI and its formulations have a significant effect on LSPI frequency.

Squish flow control is well known as a key technology for improving knock limit in spark ignition engines. However, to acquire a sufficient squish area in a four-valve engine is difficult. In order to achieve a maximum effect of knock suppression with a minimum squish area, we have developed, what we call, a Slant Squish Combustion Chamber for new engines. A slant squish compared with a conventional squish produces an effective reverse squish flow in the early expansion stroke, resulting in higher flow velocity and turbulence. Furthermore, flame propagation to squish area and end gas is accelerated. These improvements are considered to suppress the knock phenomenon. Consequently, with a slant squish, a high compression ratio, to achieve low fuel consumption and high engine performance is realized.

The use of exhaust gas recirculation (EGR) in spark ignition engines has been shown to have a number of beneficial effects under specific operating conditions. These include reducing pumping work under part load conditions, reducing NOx emissions and heat losses by lowering peak combustion temperatures, and by reducing the tendency for engine knock (caused by end-gas autoignition) under certain operating regimes. In this study, the effects of EGR addition on knocking combustion are investigated through a combined experimental and modeling approach. The problem is investigated by considering the effects of individual EGR constituents, such as CO2, N2, and H2O, on knock, both individually and combined, and with and without traces species, such as unburned hydrocarbons and NOx. The effects of engine compression ratio and fuel composition on the effectiveness of knock suppression with EGR addition were also investigated.

Engine oil formulation is known to affect low speed pre-ignition (LSPI), which creates technical restrictions on downsized turbocharged engines. Calcium, which is used to ensure detergency and anti-rust performance, is reported to increase LSPI events. Therefore, new formulation technologies are needed to satisfy both LSPI prevention performance and other conventional performance areas. The authors focused on two approaches: enhancement of LSPI prevention performance by adding a booster component and substitution of calcium for a less reactive component to balance performance areas including LSPI prevention. We have verified the effectiveness of these approaches by increasing the dosage of molybdenum used as a friction modifier as well as replacing calcium detergent with a magnesium detergent. These formulation strategies can be applicable for future ILSAC GF-6 engine oil, where a specification for LSPI prevention performance is expected to be implemented.