Search Results

This study focuses on fluctuations in the aerodynamic load acting on a hatchback car model under steady-state conditions, which can lead to degeneration of vehicle motion performance due to excitation of vehicle vibrations. Large eddy simulations were first conducted on a vehicle model based on a production hatchback car with and without additional aerodynamic devices that had received good subjective assessments by drivers. The numerical results showed that the magnitudes of the lateral load fluctuations were larger without the devices at Strouhal numbers less than approximately 0.1, where surface pressure fluctuations indicated a negative correlation between the two sides of the rear end, which could give rise to yawing and rolling vibrations. Based on the numerical results, wind-tunnel tests were performed with a 28%-scale hatchback car model.

The aerodynamic stability of energy-saving, lightweight, and low-drag vehicles is reduced by crosswind disturbances. In particular, crosswinds cause unsteady motion in vehicles with low-drag body shapes due to aerodynamic yaw moment. To verify fluctuations in the unsteady aerodynamic forces of a vehicle, a direct measurement method of these forces in a crosswind test was established using inertial force and tire load data. The former uses an inertia sensor comprised of a gyro, acceleration sensor, and GPS sensor, and the latter uses a wheel force sensor. Noise in the measurement data caused by the natural frequency of the tires was reduced using a spectral subtraction method. It was confirmed that aerodynamic data measured in the crosswind test corresponded to wind tunnel test data. Numerical expressions were defined to model the unsteady aerodynamic forces in a crosswind.

An experimental study on reducing aerodynamic drag and improving fuel economy through vehicle platooning was conducted to develop an Intelligent Transport System (ITS) with good fuel economy of the entire vehicle-based transportation society. The objectives of the present study are to achieve a simple and quick approach to estimating the aerodynamic drag reduction rates of vehicle platooning. This paper reports the prediction formula, including the conditions of various types of vehicles in multiple-vehicle platooning, based on the power law of a free turbulent axisymmetric wake and on-road experimental results. Note, the prediction formula in this study does not fully include the effect of various type of wake deficit patterns due to rear shape of vehicle and atmospheric wind. Therefore, continuous study is needed to examine the applicable limit.

A highly anti-corrosive organic-inorganic hybrid paint for automotive steel parts has been developed. The inorganic component included in the paint is silicon dioxide (SiO2), which has the capability to passivate zinc. By application of the paint on a trivalent chromatetreated zinc-plated steel sheet or a trivalent chromate-treated zinc-nickel-plated steel sheet, high anti-corrosion protection can be provided to steel materials. Particularly in the case of application over a zinc-nickel-plated steel sheet, 0 mm corrosion depth after a cyclic corrosion test (CCT) of 450 cycles was demonstrated.

This paper describes the development of a fracture finite element (FE) model for laser screw welding (LSW) and validation of the model with experimental results. LSW was developed and introduced to production vehicles by Toyota Motor Corporation in 2013. LSW offers superb advantages such as increased productivity and short pitch welding. Although the authors had previously developed fracture FE models for conventional resistance spot welding (RSW), a fracture model for LSW has not been developed. To develop this fracture model, many comprehensive experiments were conducted. The results revealed that LSW had twice as many variations in fracture modes compared to RSW. Moreover, fracture mode bifurcations were also found to result from differences in clearance between welded plates. In order to analyze LSW fracture phenomena, detailed FE models using fine hexahedral elements were developed.

High frequency wind noise caused by turbulent flow around the front pillars of a vehicle is an important factor for customer perception of ride comfort. In order to reduce undesirable interior wind noise during vehicle development process, a calculation and visualization method for exterior wind noise with an acceptable computational cost and adequate accuracy is required. In this paper an index for prediction of the strength of exterior wind noise, referred to as Exterior Noise Power (ENP), is developed based on an assumption that the acoustic power of exterior wind noise can be approximated by the far field acoustic power radiated from vehicle surface. Using the well-known Curle’s equation, ENP can be represented as a surface integral of an acoustic intensity distribution, referred to as Exterior Noise Power Distribution (ENPD). ENPD is estimated from turbulent surface pressure fluctuation and mean convective velocity in the vicinity of the vehicle surface.

In order to optimize air-fuel mixture formation in a small DI diesel engine, studies were conducted into the effects of combustion chamber shape and fuel spray impingement. Based on the findings of these studies, the shape of the combustion chamber was modified to induce complex air motion with high turbulence and fuel injection was carefully controlled to achieve optimum impingement intensity. As a result, the mixture formation process was greatly improved with a consequent gain in terms of engine performance. To clarify the reasons for this improvement in combustion, a three-dimensional calculation of the in-cylinder air motion was made. The behaviour of the spray and flame was observed using an endoscope. The new combustion system, named TOYOTA Reflex Burn system (TRB) thus developed has been adopted in production engines since August 1988.

In order to clarify the combustion behavior in the ultra high engine speed range, a new technique has been developed. This technique is composed of ionization current detection and flame observation, and is highly heat-resistant, vibration-resistant, and has a quick response. From analyzing the flame front propagation in the high-speed research engine, it was found that the flame propagated throughout the entire cylinder over almost the same crank angle period irrespective of engine speed introduction.

Fluoroelastmers are well known for their resistance to heat and fluids, and have become major material for crankcase oil seals. On the other hand, new additive formulations are developed for engine lubricants used for fuel economic gasoline engines. In this paper, the effects of those additives on properties of fluoroelastmers are investigated. The results of the immersion tests of both test plaques and oil seal products indicate that dithiocarbamates, friction modifier, have hardening effects on fluoroelastmers. The fluoroelastmer deterioration mechanism is determined by analysis of elastmer samples after immersion in oil.

Three-way catalyst shows high performance under stoichiometric atmosphere. The CeO2-ZrO2 based materials (CZ) are added as a buffer of O2 concentration. To improve the catalyst performance the larger O2 storage capacity (OSC) are needed. Theoretically, the sulfur oxidation-reduction reaction moves oxygen 8 times larger than cerium. We focused on this phenomenon and synthesized Ln2O2SO4 as a new OSC material. The experimental result under model gas shows that the OSC of Ln2O2SO4 is 5 times lager than CZ.

It is critical to develop high performance three-way catalysts to meet increasing regulations around the world. It was found that a double-layered catalyst loaded with Pt and Rh suppresses Pt-Rh alloying, thereby improving catalytic performance. A double-layered catalyst has the effect of decreasing OSC performance, but this has been overcome by a newly developed Rh support and suppressed Pt grain growth. The developed catalyst is capable of lowering the amount of PGM required by approximately 40%.

One primary result of the reduction of platinum group metals (PGM) within a catalytic converter is the decline in NOx conversion efficiency. This paper hypothesizes that the primary factor of this decline to be hydrocarbon (HC) poisoning. To maintain high NOx conversion efficiency as the PGM reduces, Rh activation improvement becomes significant to overcome the HC poisoning. Analysis of the Rh deterioration mechanism found that it is effective to separately arrange Rh and CeO2 on the converter, avoiding the Rh deactivation. By this improvement, we improved the catalyst activity at less than 25% of the original Rh loading.

Spark ignition direct injection (SIDI) engines have the potential to realize significant thermal efficiency improvements compared to conventional port fuel injection engines. The effects of fuel properties on efficiency and emissions have been investigated in a prototype of an Avensis Wagon equipped with a 2.0 liter, 4 cylinder spark ignition, direct injection (SIDI) engine designed to meet US 2000 emission standards. The vehicle employed a close coupled three-way catalyst and a NOx storage and reduction catalyst. Seven matrix fuels were blended to the same RON with varying levels of aromatics, olefins, ethanol, and volatility. Relative thermal efficiency, fuel economy, and tailpipe emissions were measured for the matrix fuels and a base fuel under the FTP LA4 driving cycle. The engine was operated in a lean burn mode in light load condition for approximately half of the driving cycle.

Toyota Motor Corporation has been developing technologies for reductions on the environmental load. This paper reports the following as a part of technological development for the painting process. Prior to the application of the E-coat, vehicle bodies are pretreated with zinc phosphates. This is applied to ensure good adhesion and corrosion resistance of the E-coat film. To obtain an excellent pretreatment film, surface conditioning with titanium colloid is generally applied before pretreatment. Since colloid flocculation control was difficult in the case of a conventional titanium colloid-type surface conditioner, the surface conditioner had to be renewed at approximately two-month intervals. The liquid life, however, increased remarkably as a result of adopting fine zinc-type surface conditioners and adding an organic protective surface layer. The water supply/discharge amount was decreased significantly compared with previous amounts.

We studied the adoption of plastics derived from plants (bioplastics) such as poly(lactic acid) (PLA) for automotive parts in order to contribute to suppressing the increase in CO, emissions. For this application. major improvements of heat and impact resistance are needed. As a method to improve heat resistance, we developed PLA combined with clay of high heat resistance. As a result. we succeeded in synthesizing a PLA-clay nanocomposite using 18(OH)2-Mont. In-mold crystallization of PLA-clay nanocomposite lead to the great suppression of storage modulus decrease at high temperature. which in turn improved the heat resistance of PLA.

In recent years the regulations governing emissions from automobiles have been strengthened as awareness of global environmental problems has increased. Furthermore, the amount of precious metals being used has continued to decrease due to concerns over the exhaustion of natural resources and worries about the risk of fluctuations in the price of these precious metals. As a result, a high performance three-way catalyst that can satisfy the emissions regulations is now required. By applying zone-coating and carrier degradation control technology, a high performance three-way catalyst has been developed. The zone-coating technology improves the conversion performance of the catalyst through improvement of HC and NOx conversion reactions and oxygen storage capacity (OSC) reactions. The addition of an Nd surface-enriched layer strengthened the mutual interactions between the carrier and Rh.

This paper presents a new application of a vehicle on-board battery charger utilizing high frequency Silicon Carbide (SiC) power devices. SiC is one of the most promising alternatives to Silicon (Si) for power semiconductor devices due to its superior material characteristics such as lower on-state resistance, higher junction temperature, and higher switching frequency. An on-board charger prototype is developed demonstrating these advantages and a peak system efficiency of 95% is measured while operating with a switching frequency of 250 kHz. A maximum output power of 6.06 kW results in a gravimetric power density of 3.8 W/kg and a volumetric power density of 5.0 kW/L, which are about 10 times the densities compared with the current Prius Plug-In Si charger. SiC technology is indispensable to eco-friendly PHV/EV development.

The research described in this paper aimed to study the cornering resistance and dissipation power on the tire contact patch, and to develop an efficient direct yaw moment control (DYC) during acceleration and deceleration while turning. A previously reported method [1], which formulates the cornering resistance in steady-state cornering, was extended to so-called quasi steady-state cornering that includes acceleration and deceleration while turning. Simulations revealed that the direct yaw moment reduces the dissipation power due to the load shift between the front and rear wheels. In addition, the optimum direct yaw moment cancels out the understeer augmented by acceleration. In contrast, anti-direct yaw moment optimizes the dissipation power during decelerating to maximize kinetic energy recovery. The optimization method proved that the optimum direct yaw moment can be achieved by equalizing the slip vectors of all the wheels.

To improve the thermal efficiency of an internal combustion engine, the application of ceramics to heat loss reduction in the cylinders has been studied [1-2]. The approach taken has focused on the low heat conductivity and high heat resistance of the ceramic. However, since the heat capacity of the ceramic is so large, there is a problem in that the wall temperature increases during the combustion cycle. This leads to a decrease in the charging efficiency, as well as knocking in gasoline engines. To overcome these problems, the application of thermal insulation without raising the gas temperature during the intake stroke has been proposed [3-4]. As a means of achieving this, we developed a "temperature swing heat insulation coating" [5, 6, 7, 8, 9]. This reduces the heat flux from the combustion chamber into the cooling water by making the wall temperature follow the gas temperature as much as possible during the expansion and exhaust strokes.

The unsteady aerodynamic loads produced due to vehicle dynamic motions affect vehicle dynamic performance attributes such as straight-line stability or handling characteristics. To improve these dynamic performances, understanding the detailed mechanisms by which unsteady aerodynamic loads are caused during dynamic motions and the effects of unsteady aerodynamic loads on vehicle dynamic performance are needed. This paper describes the numerical study of unsteady aerodynamics of a 1/4 scale car model in dynamic pitching motion to clarify the detailed mechanisms by which unsteady aerodynamic loads are caused during the motion. Vortical structures around front wheelhouse and front under side of the body are analyzed by introducing schematic views to understand the mechanisms of unsteady flow fields. Furthermore, effects of aerodynamic devices devised based on the analyses on unsteady aerodynamics are discussed.