Search Results

This paper developed a control system for the auxiliary power unit (APU) in off-road series hybrid electric special vehicle. A control system configuration was designed according to the requirements of the high voltage system in series hybrid electric special vehicle. Then optimal engine operating areas were defined. A gain scheduling engine speed PI controller was designed based on these areas. A closed loop voltage regulator was designed for the synchronous generator. The proposed control system was first validated on an APU control test bench. The test results showed the control system guaranteed the diesel APU good dynamic response characteristics while remaining stable output voltage. Finally, the APU control system was implemented on a diesel APU in an off-road series hybrid electric vehicle and a road test was conducted. The road test results showed the APU control system promised good performance in both vehicle dynamics and vehicle high voltage system.

Due to the increase of mining production and rising labor costs, manufacturers of construction and mining equipment are engaged in developing large tonnage mining truck with good dynamic performance and high transport efficiency. This paper focuses on the improvement of the dynamic performance of a 52t off-highway dump truck. According to the characteristics of its operating cycle, electric auxiliary drive system is installed in the front axle aiming at improving the utilization rate of ground adhesion. The new all-wheel drive hybrid electric system makes it possible for dump truck transports at a higher velocity. Both the conventional dump truck model and the new all-wheel drive hybrid truck model are built based on the AVL-Cruise platform. Meanwhile, under the premise of enough dynamic performance, fuel consumption can be minimized by collaborative optimization in Isight.

Power-split configuration is highlighted as the most popular concept for full hybrid electric vehicles (HEV). However, the energy management and design of power-split heavy duty truck under Chinese driving conditions still need to be investigated. In this paper, the parametric design, a rule-based control strategy and an equivalent consumption minimization strategy (ECMS) for the power-split heavy duty truck are presented. Besides, the influence of a penalty factor also discussed under ECMS algorithm. Meanwhile, two different methods to search the engine operation point have been proposed and the reason of different economy performance is presented by using energy flow chart. And the simulation results show both fuel consumption can satisfy the second phase fuel consumption standard and the third phase fuel consumption standard which will be implemented in 2020, under C-WTVC (Chinese-World Transient Vehicle Cycle).

When driving in mountainous areas, vehicles often encounter long downhill sections. Due to the large mass of bus and the drum brake with poor heat dissipation effect, it is easy for bus to produce braking thermal decay in long downhill section, which makes the vehicle out of control and causes safety accidents. The braking methods of parallel hybrid electric bus include drum braking, engine braking and regenerative braking, whose torque models are established in this paper. The coasting test in Trucksim is used to verify the correctness of the engine braking torque model. Based on coupling braking torque curve with vehicle speed in different gradient, the stable speed is determined and the shift strategy is proposed. The temperature rise model of brake drum is established to analyze the temperature change of brake drum during long downhill. Then, according to the ramp data of G22 freeway, the above models are simulated.

Due to the potential on decreasing fuel consumption and design flexibility, parallel configurations are widely used for hybrid electric vehicles (HEVs). However, the fuel economy and economic profitability of parallel HEVs for heavy-duty truck applications under Chinese driving conditions still need to be investigated. It is uneasy to improve the fuel economy of parallel HEVs with a single electric motor from control perspective only. In this article, the battery size of the architecture is optimized by using the dynamic programming (DP) approach, based on a dynamic degradation model of the LiFePO4 battery. Moreover, based on the DP results, a near-optimal control strategy of the hybrid powertrain system for online application is proposed. Finally, with two economic assumptions, the initial costs, operation costs, and payback periods are obtained in a total cost of ownership framework perspective.

With the development of economy, the road cleaning faces great challenges because the road area keeps increasing and the road types tend to be diversified. Cleaning vehicle is widely used in road surface cleaning, but it is more and more difficult to meet the demand of road surface cleaning only through using a single road surface cleaning method. If the way of manual adjustment of cleaning parameters is adopted, the driver is required to have rich experience. At present, there is an urgent need for a cleaning vehicle that can autonomously adjust cleaning parameters according to the road surface. This study is based on road recognition technology. After the pavement category is reflected by the visual sensor feedback information and the pavement adhesion coefficient, the parameters of the cleaning vehicle are adjusted by the controller to adapt to different roads.