Search Results

The aim of this work is to apply an innovative adaptive ℒ1 techniques to control flutter phenomena affecting highly flexible wings and to evaluate the efficiency of this control algorithm and architecture by performing the following tasks: i) adaptation and analysis of an existing simplified nonlinear plunging/pitching 2D aeroelastic model accounting for structural nonlinearities and a quasi-steady aerodynamics capable of describing flutter and post-flutter limit cycle oscillations, ii) implement the ℒ1 adaptive control on the developed aeroelastic system to perform initial control testing and evaluate the sensitivity to system parameters, and iii) perform model validation and calibration by comparing the performance of the proposed control strategy with an adaptive back-stepping algorithm. The effectiveness and robustness of the ℒ1 adaptive control in flutter and post-flutter suppression is demonstrated.

Connected and Autonomous Vehicles (CAV) rely on information obtained from sensors and communication to make decisions. In a Cooperative Vehicle Safety (CVS) system, information from remote vehicles (RV) is available at the host vehicle (HV) through the wireless network. Safety applications such as crash warning algorithms use this information to estimate the RV and HV states. However, this information is uncertain and sparse due to communication losses, limitations of communication protocols in high congestion scenarios, and perception errors caused by sensor limitations. In this paper we present a novel approach to improve the robustness of the CVS systems, by proposing an architecture that divide application and information/perception subsystems and a novel prediction method based on non-parametric Bayesian inference to mitigate the detrimental effect of data loss on the performance of safety applications.

This paper presents the concept of a dual latent heat sink for thermal management of pulse heat generating electronic systems. The focus of this work is to verify the effectiveness of the concept during charging through experimentation. Accordingly, custom components were built and a prototype version of the heat sink was fabricated. Experiments were performed to investigate the implementation feasibility and heat transfer performance. It is shown that this heat sink is practicable and helps in arresting the system temperature rise during charging (period of pulse heat load).

Complex aerospace engineering systems require innovative methods for performance monitoring and anomaly detection. The interface of a real-time data stream to a system for analysis, pattern recognition, and anomaly detection can require distributed system architectures and sophisticated custom programming. This paper presents a case study of a simplified interface between Programmable Logic Controller (PLC) real-time data output, signal processing, cloud computing, and tablet systems. The discussed approach consists of three parts: First, the connectivity of real-time data from PLCs to the signal processing algorithms, using standard communication technologies. Second, the interface of legacy routines, such as NASA's Inductive Monitoring System (IMS), with a hybrid signal processing system. Third, the connectivity and interaction of the signal processing system with a wireless and distributed tablet, (iPhone/iPad) in a hybrid system configuration using cloud computing.

An innovative nonlinear simulation approach for high power density synchronous generator systems is developed and implemented. Due to high power density, the generator operates in nonlinear region of the magnetic circuit. Magnetic Finite Element Analysis (FEA) makes nonlinear simulation possible. Neural network technique provides nonlinear functions for system level simulation. Dynamic voltage equation provides excellent mathematical model for system level simulations. Voltage, current, and flux linkage quantities are applied in Direct-Quadrature (DQ) rotating frame. The simulated system includes main machine, exciter, rectifier bridge, bang-bang control, and PI control circuitry, forming a closed loop system. Each part is modeled and then integrated into the system model.

This paper reviews the literature which identifies the causes, consequences and cures for engine knock as it affects high performance engines. The physical events of normal and abnormal combustion are described. The observed variations in combustion phenomenon are explained through chemical kinetics. A mathematical model of combustion which can predict knock in an engine cylinder is summarized. Several mechanisms of knock induced damage are outlined. Design and operating considerations which affect an engine's propensity to knock are discussed. Terms that have become associated with combustion in general and the knocking phenomenon in particular are collected and examined

A power electronics module was equipped with an evaporative spray cooling nozzle assembly that served to remove waste heat from the silicon devices. The spray cooling nozzle assembly took the place of the standard heat sink, which uses single phase convection. The purpose of this work was to test the ability of spray cooling to enable higher power density in power electronics with high temperature coolant, and to be an effective and lightweight system level solution to the thermal management needs of aerospace vehicles. The spray cooling work done here was with 95 °C water, and this data is compared to 100 °C water/ propylene glycol spray cooling data from a previous paper so as to compare the spray cooling performance of a single component liquid to that of a binary liquid such as WPG. The module used during this work was a COTS module manufactured by Semikron, Inc., with a maximum DC power input of 180 kW (450 VDC and 400 A).

Effective thermal management and removal of the waste heat generated at diode arrays is critical to the development of high-power solid-state lasers. Thermal design must be considered in the packaging of these arrays. Two different packages with heat dissipation through spray cooling are evaluated experimentally and numerically. Their overall performance is compared with other packaging configurations using different heat removal approaches. A novel packaging design is proposed that can fulfill the requirements of low thermal resistance, temperature uniformity among emitters in the diode array, low coolant flow rate, simplicity and low assembly cost. The effect of temperature uniformity on the pumping efficiency for gain media is examined for our novel packaging design. The thermal stress induced by temperature variation within an emitter is also considered.

Engine dynamometer testing of homogeneous charge, spark ignition lean burn engines fueled by natural gas, hydrogen/natural gas blends and neat hydrogen was conducted to determine if NOx emissions from blended fuel operation can be reduced below those generated from natural gas operation, approaching those due to a 100% hydrogen fueled engine. The preliminary tests were conducted at the University of Central Florida/Florida Solar Energy Center on an eight cylinder automotive engine. The results indicate that the hydrogen/natural gas fuel has the potential of meeting highly restrictive NOx levels. Sandia National Laboratories conducted follow-on, comparative tests using a single cylinder research engine. The Sandia results indicate that the proposed CARB EZEV standard for NOx can be met without exhaust gas aftertreatment using a 30% hydrogen (by volume) / 70% natural gas blend fuel in a constant speed/power, hybrid vehicle application which achieves 60 MPG gasoline equivalent efficiency.

In this study we consider the coordinated exploration of an unfamiliar Martian landscape by a swarm of small autonomous rovers, called Swarmies, simulated in a distributed setting. With a sustainable program of return missions to and from Mars in mind, the goal of said exploration is to efficiently prospect the terrain for water meant to be gathered and then utilized in the production of rocket fuel. The rovers are tasked with relaying relevant data to a home base that is responsible for maintaining a mining schedule for an arbitrarily large group of rovers extracting water-rich regolith. For this reason, it is crucial that the participants maintain a wireless connection with one another and with the base throughout the entire process. We describe the architecture of our simulation which is composed of HLA-compliant components that are visualized via the Distributed Observer Network tool developed by NASA.

In this paper, we address the thermal management issues which limit the lifespan, specific power and overall efficiency of an air-cooled rotary Wankel engine used in Unmanned Air Vehicles (UAVs). Our goal is to eliminate the hot spots and reduce the temperature gradients in the engine housing and side plates by aggressive heat spreading using heat pipes. We demonstrate by simulation that, for a specific power requirement, with heat spreading and more effective heat dissipation, thermal stress and distortion can be significantly reduced, even with air cooling. The maximum temperature drop was substantial, from 231°C to 129°C. The temperature difference (measure of temperature uniformity) decreased by 8.8 times (from 159°C to 18°C) for a typical UAV engine. Our heat spreaders would not change the frontal area of the engine and should have a negligible impact on the installed weight of the propulsion assembly.

Laminar burning velocity (LBV) measurements are reported for promising high-performance fuels selected as drop-in transportation fuels to automotive grade gasoline as part of the United States Department of Energy’s Co-Optimization of Fuels and Engines Initiative (Co-Optima). LBV measurements were conducted for ethanol, methyl acetate, and 2-methylfuran with synthetic air (79.0 % N2 and 21.0 % O2 by volume) within a constant-volume spherical combustion rig. Mixture initial temperature was fixed at 428±4 K, with the corresponding initial pressure of 1.00±0.02 atm. Current LBV of ethanol is in good agreement with literature data. LBV of ethanol and 2-methylfuran showed similar values over the range of equivalence ratios, while methyl acetate exhibited an LBV significantly lower over the range of tested equivalence ratios. The maximum laminar burning velocity occurred at slightly richer equivalence ratio from the stoichiometric value for all fuels tested.