Search Results

A series of rigid wall tests have been conducted at three impact velocities to quantify the dynamic response of the Side Impact Dummy (SID) developed by US DOT. This paper reports the chest, pelvis and head responses of the dummy at various filter frequencies and describes the development and verification of the three-dimensional mathematical model of the Side Impact Dummy utilizing the rigid wall test results. The mathematical model uses the mass distribution and the linkage system of the current Part 572, Hybrid II dummy which forms the basic platform of the SID. The unique chest of the dummy is modeled by two systems of linkages simulating the rib cage and the jacket. Also included in the model is the internal hardware of the chest, e.g. a damper, rib stopper and a clavicle simulator at the upper spine. The material and linkage models are based on static and dynamic tests of the dummy components.

This paper describes the development of a three-dimensional lumped-mass structure and dummy model to study barrier-to-car side impacts. The test procedures utilized to develop model input data are also described. The model results are compared to crash test results from a series of six barrier-to-car crash tests. Sensitivity analysis using the validated model show the necessity to account for dynamic structural rate effects when using quasi-statically measured vehicle crush data.

Two 50th percentile anthropomorphic test devices are specified as alternate test devices for FMVSS 208 compliance testing. These test devices are commonly known as the Hybrid II and the Hybrid III dummies. The designs of the two dummies are different, representing the state-of-the-art in the time frame of their designs. The trajectory differences between the two dummies have been published in the literature, but response differences, e.g., HIC and chest acceleration are not available in the literature. To quantify response differences between the two dummies, a series of sled tests with open bucks and with bucks simulating vehicle interior were conducted with restrained dummies. Additional crash tests were also conducted with the two dummies. This paper reports on an analysis of the data from the above series of tests. The data indicate that in non-head contact simulations with belt restraint systems, Hybrid III HIC's are nearly 50% higher than Hybrid II HIC's.

The objective of this study was to analyze available anthropomorphic test device (ATD) responses from KARCO rear impact tests and to evaluate an injury predictive model based on crash severity and occupant weight presented by Saczalski et al. (2004). The KARCO tests were carried out with various seat designs. Biomechanical responses were evaluated in speed ranges of 7-12, 13-17, 18-23 and 24-34 mph. For this analysis, all tests with matching yielding and stiff seats and matching occupant size and weight were analyzed for cases without 2nd row occupant interaction. Overall, the test data shows that conventional yielding seats provide a high degree of safety for small to large adult occupants in rear crashes; this data is also consistent with good field performance as found in NASS-CDS. Saczalski et al.'s (2004) predictive model of occupant injury is not correct as there are numerous cases from NASS-CDS that show no or minor injury in the region where serious injury is predicted.

Macroscopic constitutive behaviors of aluminum 5052-H38 honeycombs under dynamic inclined loads with respect to the out-of-plane direction are investigated by experiments. The results of the dynamic crush tests indicate that as the impact velocity increases, the normal crush strength increases and the shear strength remains nearly the same for a fixed ratio of the normal to shear displacement rate. The experimental results suggest that the macroscopic yield surface of the honeycomb specimens as a function of the impact velocity under the given dynamic inclined loads is not governed by the isotropic hardening rule of the classical plasticity theory. As the impact velocity increases, the shape of the macroscopic yield surface changes, or more specifically, the curvature of the yield surface increases near the pure compression state.

This study applies a detailed finite element model of the human body to simulate occupant knee impacts experienced in vehicular frontal crashes. The human body model includes detailed anatomical features of the head, neck, chest, thoracic and lumbar spine, abdomen, and lower and upper extremities. The material properties used in the model for each anatomic part of the human body were obtained from test data reported in the literature. The total human body model used in the current study has been previously validated in frontal and side impacts. Several cadaver knee impact tests representing occupants in a frontal impact condition were simulated using the previously validated human body model. Model impact responses in terms of force-time and acceleration-time histories were compared with test results. In addition, stress distributions of the patella, femur, and pelvis were reported for the simulated test conditions.

A theoretical, mathematical, risk assessment procedure was developed to estimate the fraction of drivers that incurred head and thoracic AIS3+ injuries in full-engagement frontal crashes. The estimates were based on numerical simulations of various real-world events, including variations of crash severity, crash speed, level of restraint, and occupant size. The procedure consisted of four steps: (1) conduct the simulations of the numerous events, (2) use biomechanical equations to transform the occupant responses into AIS3+ risks for each event, (3) weight the maximum risk for each event by its real-world event frequency, and (4) sum the weighted risks. To validate the risk assessment procedure, numerous steps were taken. First, a passenger car was identified to represent average field performance.

Risk curves are developed for several crash data sets, expressing the probabilities of injury as a function of HIC, Extension Moment, Neck Tension and Maximum Deflection, respectively. The statistical method uses concept of thresholds that are interval censored and right censored. A combined evaluation method is used to select a “best” curve among the curves derived from various methods.

The result of two series of crash tests, 5 tests each series, are presented in this paper. Two car designs were subjected to various frontal impacts - full frontal, car-to-car 60% offset, 50% offset, and 50% offset with deformable barrier - at 56 km/h. Two tests were conducted at 60 km/h against the ECE deformable barrier with 40% overlap. Structural and occupant responses are compared between the various test conditions.

The potential of head injury in frontal barrier impact tests was investigated by a mathematical model which consisted of a finite element human head model, a four segments rigid dynamic neck model, a rigid body occupant model, and a lumped-mass vehicle structure model. The finite element human head model represents anatomically an average adult head. The rigid body occupant model simulates an average adult male. The structure model simulates the interior space and the dynamic characteristics of a vehicle. The neck model integrates the finite element human head to the occupant body to give a more realistic kinematic head motion in a barrier crash test. Model responses were compared with experimental cadaveric data and vehicle crash data for the purpose of model validation to ensure model accuracy. Model results show a good agreement with those of the tests.

Locations of key body segments of Hybrid III dummies used in FMVSS 208 compliance tests and NCAP tests were measured and subjected to statistical analysis. Mean clearance dimensions and their standard deviations for selected body segments of driver and passenger occupants with respect to selected vehicle surfaces were determined for several classes of vehicles. These occupant locations were then investigated for correlation with impact responses measured in crash tests and by using a three dimensional human-dummy mathematical model in comparable settings. Based on these data, the importance of some of the clearance dimensions between the dummy and the vehicle surfaces was determined. The study also compares observed Hybrid III dummy positions within selected vehicles with real world occupant positions reported in published literature.

Axial loading of the calcaneus-talus-tibia complex is an important injury mechanism for moderate and severe vehicular foot-ankle trauma. To develop a more definitive and quantitative relationship between biomechanical parameters such as specimen age, axial force, and injury, dynamic axial impact tests to isolated lower legs were conducted at the Medical College of Wisconsin (MCW). Twenty-six intact adult lower legs excised from unembalmed human cadavers were tested under dynamic loading using a mini-sled pendulum device. The specimens were prepared, pretest radiographs were taken, and input impact and output forces together with the pathology were obtained using load cell data. Input impact forces always exceeded the forces recorded at the distal end of the preparation. The fracture forces ranged from 4.3 to 11.4 kN.

Global engineering is increasingly becoming a practice within the automotive industry. Due to added engineering and manufacturing benefits, more and more new vehicles are being developed with common structure to meet the consumer needs in many local regions. While vehicle development and manufacturing process is becoming global, automotive safety regulations in various parts of the world have not been as uniform. A good example is the differing requirements for dynamic side impact protection of new vehicles. United States National Highway Traffic Safety Administration (NHTSA) and European Union (EU) have each produced their own distinct test procedures such as, different barrier faces, impact configurations, and anthropomorphic test devices (dummies). Although both test procedures have the same final objective estimate occupant responses in side impacts, they differ greatly in execution and emphasis on occupant response requirements.

This paper compares and contrasts the modeling features present in the MVMA2D and the MADYM02D occupant simulation models. Simulations of a series of sled tests with a Hybrid II test dummy restrained with a 3-point belt system have been conducted using the MADYM02D model. The simulation results agree with the test results.

The objective of this study was to analyze available anthropomorphic test device (ATD) responses from FMVSS 301-type rear impact tests. Rear impact test data was obtained from NHTSA and consisted of dummy responses, test observations, photos and videos. The data was organized in four test series: 1) NCAP series of 30 New Car Assessment Program tests carried out at 35 mph with 1979-1980 model year vehicles, 2) Mobility series of 14 FMVSS 301 tests carried out at 30 mph with 1993 model year vehicles, 3) 301 MY 95+ series of 79 FMVSS 301 tests carried out at 30 mph with 1995-2005 model year vehicles and 4) ODB series of 17 Offset Deformable Barrier tests carried out at 50 mph with a 70% overlap using 1996-1999 model year vehicles. The results indicate very good occupant performance in yielding seats in the NCAP, Mobility and 301 MY 95+ test series.

A new inflator specification, the “inflator thrust variable,” was developed to better explain measured mid-sized male, instrumented test dummy responses in the chest-on-module test condition. Specifically, controlled laboratory experiments were conducted with non-production, driver airbag modules with inflators of various outputs and gas constituents in an effort to assess their effects on a pertinent occupant response. Regression analyses showed that the inflator thrust variable is a better predictor of the observed variation in peak viscous criterion responses than either peak tank pressure or the related pressure rise rate when inflators of differing gas composition were compared.

The biomechanical behavior of 4-point seat belt systems was investigated through MADYMO modeling, dummy tests and post mortem human subject tests. This study was conducted to assess the effect of 4-point seat belts on the risk of thoracic injury in frontal impacts, to evaluate the ability to prevent submarining under the lap belt using 4-point seat belts, and to examine whether 4-point belts may induce injuries not typically observed with 3-point seat belts. The performance of two types of 4-point seat belts was compared with that of a pretensioned, load-limited, 3-point seat belt. A 3-point belt with an extra shoulder belt that “crisscrossed” the chest (X4) appeared to add constraint to the torso and increased chest deflection and injury risk. Harness style shoulder belts (V4) loaded the body in a different biomechanical manner than 3-point and X4 belts.

A new, AIS3+ thoracic risk equation based on chest deflection was derived and assessed for drivers subjected to concentrated (belt-like) loading. The new risk equation was derived from analysis of an existing database of post mortem human subjects in controlled, laboratory sled tests. Binary logistic regression analysis was performed on a subset of the data, namely, 25th-75th percentile men (by weight) from 36-65 years old whose thoracic deformation patterns were due to concentrated (belt-like) loading. Other subsets of data had insufficient size to conduct the analysis. The resulting thoracic risk equation was adjusted to predict the AIS3+ thoracic risks for average-aged occupants in frontal crashes (i.e., 30 years old). Biomechanical scaling was used to derive the corresponding relationships for the small female and large male dummies. The new thoracic risk equations and three other sets of existing equations were evaluated as predictors of real-world crash outcomes.

This paper describes improvements made to the injury risk curves for peak neck tension, peak neck extension moment and a linear combination of tension and extension moment that produce peak stress in the anterior-longitudinal ligament at the head-to-neck junction. Data from previously published experiments that correlated neck injuries to 10-week-old, anesthetized pigs and neck response measurements of a 3-year-old child dummy that were subjected to similar airbag deployments are updated and used to generate Normal probability curves for the risk of AIS ≥ 3 neck injury for the 3-year-old child. These curves are extended to other sizes and ages by normalizing for neck size. Factors for percent of muscle tone and ligamentous failure stress as a function of age are incorporated in the risk analysis. The most sensitive predictor of AIS ≥ 3 neck injury for this data set is peak neck tension.

The purpose of this study is to evaluate the hard tissue injury -predictive value of various thoracic injury criteria when the restraint conditions are varied. Ten right-front passenger human cadaver sled tests are presented, all of which were performed at 48 km/h with nominally identical sled deceleration pulses. Restraint conditions evaluated are 1) force-limiting belt and depowered airbag (4 tests), 2) non-depowered airbag with no torso belt (3 tests), and 3) standard belt and depowered airbag (3 tests). Externally measured chest compression is shown to correspond well with the pre sence of hard tissue injury, regardless of restraint condition, and rib fracture onset is found to occur at approximately 25% chest compression. Peak acceleration and the average spinal acceleration measured at the first and eighth or ninth thoracic vertebrae are shown to be unrelated to the presence of injury, though clear variations in peaks and time histories among restraint conditions can be seen.