Search Results

In order to realize the high compression ratio and high dilution combustion toward improvement in thermal efficiency, the improvement in stability of ignition and initial phase of combustion under the high gas flow field is the major challenge. In terms of the shift on the higher power side of the operating point by downsizing and improvement of real world fuel consumption, the improvement of ignitability is increasingly expected in the wide operating range also including high load and high engine speed region. In this study, the effects of the gas pressure, gas flow velocity near the spark gap at ignition timing, and discharge current characteristics on spark channel formation were analyzed, focusing on restrike event and spark channel stretching in the spark channel formation process. And the relationship between the average discharge current until 1 ms and the EGR combustion limit was considered.

Control of turbulence during the compression stroke is suggested by both theoretical calculations and experimental results obtained with an LDV measurement in a motored engine. The authors have found experimentally that when an axial distribution of swirl intensity exists, a large-scale annular vortex is formed inside the cylinder during the compression stroke and this vortex generates and transports turbulence energy. A numerical calculation is adopted to elucidate this phenomenon. Then, an axial stratification of swirl intensity is found to generate a large-scale annular vortex during the compression stroke by an interaction between the piston motion and the axial pressure gradient. The initial swirl profile is parametrically varied to assess its effect on the turbulence parameters. Among calculated results, turbulence energy is enhanced strongest when the swirl intensity is highest at the piston top surface and lowest at the bottom surface of the cylinder head.

In this study, the characteristics of diesel spray droplets, such as the velocity and the diameter were simultaneously measured by using an improved ILIDS (Interferometric Laser Imaging for Droplet Sizing) method on a 2D plane to evaluate the droplet breakup modeling. In numerical analysis, DDM (Discrete Droplet Model) was employed with sub-models such as droplet breakup, droplet drag force and turbulence. Experiments have been performed with an accumulator type unit-injector system and a constant-volume high-pressure vessel under the condition of quiescent ambient gas. The injection pressure and ambient gas pressure were set up to 100 MPa and 0.1 / 1 MPa, respectively. The nozzle orifice diameter was 0.244 mm with a single hole. The measurement region was chosen at 40 ∼ 60 mm from the nozzle-tip. Numerical analysis of diesel sprays was conducted and the results were compared to the measured results.

Because the two-stroke gasoline engine has a feature of high power density, it might become a choice for automobiles' power train if the high HC exhaust emissions and high fuel consumption rate could be improved. As the GDI technology is quite effective for two-stroke engines, a Schnurle-type small engine was modified to a GDI engine, and its performance was tested. Also, numerical analysis of the mixture-formation process was carried out. Results indicated it was possible to reduce both the HC emissions and fuel consumption drastically with the same maximum power as a carbureted engine at WOT condition. However, misfiring in light load condition was left unresolved. Numerical analysis clarified the process of how the mixture formation got affected by the injector location, injection timing, and gas motion.

A Direct Injection Stratified Charge Rotary Engine ( DISC-RE ) with a pilot flame ignition system has been studied to find the possibility of simultaneous reductions of fuel consumption rate and HC exhaust gas emissions. Firstly, combustion characteristics in a model combustion chamber, which simulates the DISC-RE were examined from the viewpoints of calculation and experiment. The high speed photography and the indicated pressure analysis were experimentally performed while numerical calculations of the mixture formation and combustion processes were also carried out. As a result, it has been found that the combustion using the pilot flame ignition system is much activated and a better ignitability is attained under lean mixtures than using a spark ignition system. Secondly, a single rotor with 650 cc displacement DISC-RE was built as a prototype. Combustion characteristics and its performance were tested using a combustion analyzer.

Stratified charge combustion system is widely used for production engines due to the significant potentials, such as low fuel consumption rate and low exhaust gas emissions. The combustion phenomena in simplified stratified charge conditions have been examined with changing the initial turbulence intensity, degree of mixture charge stratification, and kinds of fuels in order to clarify the features. Moreover, it should be noted that the stratified charge combustion may cause raising NOx formation. EGR (Exhaust Gas Recirculation) system is widely used for this solution. In this study, EGR was simulated by using dilution gases, such as CO2 and N2. Combustion characteristics in homogeneous and stratified charge fields with dilution gas were examined. As a result, some interesting combustion characteristics between CO2 and N2 depending on the specific heat, initial turbulence intensity, and degree of charge stratification were found.

Among the emerging technologies in order to meet ever stringent emission and fuel consumption regulations, Exhaust Gas Recirculation (EGR) system is becoming one of the prerequisites particularly for diesel engines. Although EGR cooler is considered to be an effective measure for further performance enhancement, exhaust gas soot deposition may cause degradation of the cooling. To address this issue, the authors studied the visualization of the soot deposition and removal phenomena to understand its behavior. Based on thermophoresis theory, which indicates that the effect of thermophoresis depends on the temperature difference between the gas and the wall surface exposed to the gas, a visualization method using a heated glass window was developed. By using glass with the transparent conductive oxide: tin-doped indium oxide, temperature of the heated glass surface is raised.

An improvement of thermal efficiency of internal combustion engines is strongly required. Meanwhile, from the viewpoint of refinery, CO2 emissions and gasoline price decrease when lower octane gasoline can be used for vehicles. If lower octane gasoline is used for current vehicles, fuel consumption rate would increase due to abnormal combustion. However, if a Homogeneous Charge Compression Ignition (HCCI) engine were to be used, the effect of octane number on engine performance would be relatively small and it has been revealed that the thermal efficiency is almost unchanged. In this study, the engine performance estimation of HCCI combustion using lower octane gasoline as a vision of the future engine was achieved. To quantitatively investigate the fuel consumption performance of a gasoline HCCI engine using lower octane fuel, the estimation of fuel consumption under different driving test cycles with different transmissions is carried out using 1D engine simulation code.

Reduction in the cycle-to-cycle variation (CCV) of combustion in internal combustion engines is required to reduce fuel consumption, exhaust emissions, and improve drivability. CCV increases at low load operations and lean/dilute burn conditions. Specifically, the factors that cause CCV of combustion are the cyclic variations of in-cylinder flow, in-cylinder distributions of fuel concentration, temperature and residual gas, and ignition energy. However, it is difficult to measure and analyze these factors in a production engine. This study used an optically accessible single-cylinder engine in which combustion and optical measurements were performed for 45 consecutive cycles. CCVs of the combustion and in-cylinder phenomena were investigated for the same cycle. Using this optically accessible engine, the volume inside the combustion chamber, including the pent-roof region can be observed through a quartz cylinder.

A prediction model of the cycle-to-cycle variation of the in-cylinder flow in IC engines which employs the time averaged k-ε turbulence model is proposed. The concept is based on an assumption that the power spectrum of the cycle-to-cycle variation can be deduced from the power spectra of both the mean velocity and turbulence intensity. To validate this model, in-cylinder velocity measurement in a transparent cylinder engine with a 2-valve cylinder-head is made using an LDV system. Comparisons of in-cylinder flow fields between the calculation and measurement show a good agreement in the cycle-to-cycle variation as well as the turbulence intensity. Finally, this model is applied to three kinds of flow fields to examine how the cycle-to-cycle variation may be effected. As a result, it is found that the swirl flow is effective to reduce the cycle-to-cycle variation, while the tumbling flow enhances the turbulence generation around the compression TDC.

Conventional two-stroke engines have defects such as unstable combustion, high fuel consumption rate and high HC emissions. In order to overcome the defects, a direct fuel injection system and a novel scavenging system were adopted. The authors tested a newly developed reverse uniflow-type two-stroke direct injection gasoline engine that was designed by numerical simulations. In comparison with the base engine at low engine speed, HC emission was decreased by up to 80%, and BSFC was reduced by around 40%. Power and BSFC were superior to those of a latest port-injection four-stroke engine. Furthermore, it was found that engine performance of exhaust gas emissions, fuel economy or output power can be selectively optimized by switching homogeneous and stratified combustion.

The purpose of this paper is to find a way to extend the high load limit of homogeneous charge compression ignition (HCCI) combustion. This paper presents the effect of in-cylinder flow and stratified mixture on HCCI combustion by experiments and three-dimensional computer fluid dynamics coupled with a detailed chemical reaction calculation. The first study was conducted using a rapid compression and expansion machine (RCEM) equipped with a flow generation plate to create in-cylinder turbulent flow and with a control unit of in-cylinder wall temperature to create in-cylinder temperature distribution. The study assesses the effect of the turbulent flow and the temperature distribution on HCCI combustion. In the second study, the numerical simulation of HCCI combustion was conducted using large eddy simulation coupled with a detailed chemical reaction calculation. The study analyzes the interaction between in-cylinder turbulent flow and mixture distribution and HCCI combustion.

The analysis of spray characteristics is important to examine the combustion characteristics of DI (Direct Injection) gasoline engines because the fuel-air mixture formation is controlled by spray characteristics and in-cylinder gas motion. However, the mixture formation process has not been well clarified yet. In this study, the characteristics of a fan-shaped spray caused from a slit-type injector, such as the droplet size, its velocity and the droplet distribution were simultaneously measured on a 2D plane by using improved ILIDS (Interferometric Laser Imaging for Droplet Sizing) method. ILIDS method is an optical measurement technique using interference fringes by illuminating a transparent spherical particles with a coherent laser light. In the measurement of the wall-impinging spray, effects of the distance to the wall and the wall temperature on the spray characteristics were investigated.

An optimization of thermal management system in a gasoline engine is considered to improve thermal efficiency by minimizing the cost increase without largely changing the configuration of engine system. In this study, the influence of water temperature and intake air temperature on thermal efficiency were investigated using an inline four-cylinder 1.2L gasoline engine. In addition, one-dimensional engine simulations were conducted by using a software of GT-SUITE. Brake thermal efficiency for different engine speeds and loads could be quantitatively predicted with changing the cooling water temperature in the cylinder head. Then, in order to predict the improvement of the fuel consumption in actual use, vehicle mode running simulation and general-purpose engine transient mode simulation were carried out by GT-SUITE. As a result, it was found that by controlling the temperatures of the cooling water and intake gas, thermal efficiency can be improved by several percent.

The purpose of this paper is to find a way to extend the high load limit of homogeneous charge compression ignition (HCCI) combustion. A newly developed rapid compression and expansion machine (RCEM) was employed to reproduce the typical HCCI high load condition. The in-cylinder turbulence was created by the special piston which equipped with a flow guide plate. Meanwhile, the ambient temperature distribution in the cylinder was determined by the wall temperature controlling system which was controlled by the independent coolant passages. In addition, the numerical simulation by using large eddy method coupled with a detailed chemical reaction was conducted as well. The results show that HCCI mode is potential to be improved at high load condition in full consideration of in-cylinder temperature, flow, and turbulence.

In this report, the effect of injection specification, such as droplet size, lengths of nozzle tip and spray angle, on the engine performance was investigated using a 1.2 L port fuel injection (PFI) four-cylinder gasoline engine. The experimental conditions were selected to cover the daily operating mode, including the cold start and catalyst heating process. The experiments were conducted by varying not only the injectors but also the injection timing which was shifted from the exhaust to intake stroke. The results were evaluated by the fuel consumption and exhaust gas emissions. When these tests were conducted on a production engine, a carefully designed tumble generator was installed at the intake port to enhance the intake air flow. As a result, the injection specifications showed a potential to obtain less fuel consumption and lower engine-out emissions was evaluated.

To realize stable combustion in lean or diluted conditions, reducing cycle-to-cycle variations of flow and fuel distribution is important. In this study, the effect of initial flow field was examined by simultaneous Time-Resolved PIV and visualization on two cross-sections in a fully optical-access engine under motoring and firing conditions with homogeneous pre-mixture. As a result, Omega index was defined and plotted on the correlation map between turbulence kinetic energy and CA10 (duration from ignition timing to 10% to the total accumulated heat). The omega index describes the strength of a horizontal flow field that resembles the shape of the Greek letter Omega. The plots with high Omega index were found frequently in the CA10 retarded cycles. On the other hand, the plots with low Omega index have simple tumble flows and the correlation was clearly found.