Search Results

Abstract Based on the characteristics of high strength and modulus of carbon fiber-reinforced composite (CFRP), in this article, the CFRP material was used to replace the steel material of the automobile’s B-pillar inner and outer plates, and the three-stage optimization design of the lamination structure was carried out. Firstly, this article used the principle of equal stiffness replacement to determine the thickness of the carbon fiber B-pillar inner and outer plates, and the structural design of the replaced B-pillar was also carried out. Secondly, on the basis of the vehicle collision model, the B-pillar subsystem model was extracted, and the material replacement and collision simulation were carried out.

Abstract Carbon fiber reinforced plastic (CFRP) has been used in automobiles as well as airplanes. Because of its light weight and high strength, CFRP is a good choice for making vehicle bodies lighter, which would improve fuel economy. Conventional metal bodies provide a convenient body return for electric wiring and offer good shielding against electromagnetic fields. Although CFRP is a conductor, its conductivity is much lower than that of metals. Therefore, CFRP bodies are usually not useful for electric wiring. In thunderstorms, an automotive body is considered to be a Faraday cage that protects the vehicle’s occupants from the potential harms of lightning. Before CFRP becomes widely applied to automotive bodies, its electric and electromagnetic properties need to be investigated in order to determine whether it also works as a Faraday cage against lightning. In this article, CFRP and metal body vehicles were tested under artificial lightning.

Abstract During vehicle braking, friction forces generated on the vehicle tires and the vehicle resisting aerodynamic forces play a critical role that impact the vehicle’s longitudinal braking dynamics such as stopping distance and time. These forces are mainly the tires’ braking and rolling resisting forces, vehicle lift, and drag forces. The vehicle aerodynamic forces cannot be neglected due to their impact on the vehicle’s longitudinal dynamics, especially at high vehicle speeds. This article investigates the impact of the vehicle’s rear spoiler on both vehicle aerodynamic forces and longitudinal dynamic, such as stopping distance and time. A computational fluid dynamics (CFD) model using ANSYS-Fluent® is employed to precisely estimate the vehicle’s aerodynamic forces in the case of a vehicle without and with a rear spoiler.

Abstract This article presents a fault diagnosis approach for roller bearing by applying the autocorrelation approach to filtered vibration measured signal. An optimal Morlet wavelet filter is applied to eliminate the frequency associated with interferential vibrations; the raw measured signal is filtered with a band-pass filter based on a Morlet wavelet function whose parameters are optimized based on maximum Kurtosis. Autocorrelation enhancement is applied to the filtered signal to further reduce the residual in-band noise and highlight the periodic impulsive feature. The proposed technique is used to analyze the experimental measured signal of investigated vehicle gearbox. An artificial fault is introduced in vehicle gearbox bearing an orthogonal placed groove on the inner race with the initial width of 0.6 mm approximately. The faulted bearing is a roller bearing located on the gearbox input shaft - on the clutch side.

Abstract In this experimental and computational study a novel application of aerodynamic principles in altering the pressure recovery behavior of an automotive-type ground-effect diffuser was investigated as a means of enhancing downforce. The proposed way of augmenting diffuser downforce production is to induce in its pressure recovery action a second pressure drop and an accompanying pressure rise region close to the diffuser exit. To investigate this concept with a diffuser-equipped bluff body, an inverted wing was situated within the diffuser flow channel, close to the diffuser exit. The wing’s suction surface acts as a passive flow control device by increasing streamwise flow velocity and reducing static pressure near the diffuser exit. Therefore, a second-stage pressure recovery develops along the diffuser’s overall pressure recovery curve as the flow travels from the diffuser’s low pressure, high velocity inlet to its high pressure, low velocity exit.

Abstract Heat generation characteristics of lithium ion batteries are vital for both the optimization of the battery cells and thermal management system design of battery packs. Compared with other factors, internal resistance has great influence on the thermal behavior of Li-ion batteries. Focus on a 3 Ah pouch type battery cell with the NCM/C material system, this paper quantitatively evaluates the battery heat generation behavior using an Extended Volume-Accelerating Rate Calorimeter in combination with a battery cycler. Also, internal resistances of the battery cell are measured using both the hybrid pulse power characteristic (HPPC) and electro-chemical impedance spectroscopy (EIS) methods. Experimental results show that the overall internal resistance obtained by the EIS method is close to the ohmic resistance measured by the HPPC method. Heat generation power of the battery cell is small during discharge processes lower than 0.5 C-rate.

Abstract ISO 26262 needs to be considered when developing safety-relevant E/E systems within the automotive industry. One part of the development process according to ISO 26262 is the derivation of the safety requirements for component functions. Here, one attribute of the safety requirements is the Automotive Safety Integrity Level (ASIL). The ASIL at a component level can be determined using ASIL allocation and decomposition. Considering complex systems such as vehicle electrical systems, countless possibilities can be identified for how the ASILs at a component level can be assigned in line with safety goals. In terms of efficiency, manual assignment is not expedient. Therefore, an algorithm for automated assignment of the ASILs will be introduced which considers constraints based on a fault tree analysis. The function of the approach will be demonstrated using the example of a vehicle electrical system from an automated vehicle.

Abstract Battery Drain problems can occur in the vehicle due to improper network management between electronic control units (ECUs). Aim of this paper is to identify the factors that cause transmission and cease of transmission of a network management message of an ECU along with its application messages that controls the sleep/wake-up performance of other ECUs in the network. Strategy used here is, based on the root cause analysis of problems found in Display unit in vehicle environment, the functional CAN signals impacting sleep/wake-up behavior is re-mapped along with the state flow transition of AUTOSAR NM Algorithm. A re-defined test case design and simulation for vehicle model is created. Especially it focuses on validating the impact of functional CAN signals on DUT’s sleep/wake-up performance.

Abstract The high-frequency noise issue is one of the most significant noise, vibration, and harshness problems, particularly in battery electric vehicles (BEVs). The sound package treatment is one of the most important approaches toward solving this problem. Owing to the limitations imposed by manufacturing error, assembly error, and the operating conditions, there is often a big difference between the actual values and the design values of the sound package components. Therefore, the sound package parameters include greater uncertainties. In this article, an uncertainty analysis method for BEV interior noise was developed based on an interval model to investigate the effect of sound package uncertainty on the interior noise of a BEV. An interval perturbation method was formulated to compute the uncertainty of the BEV’s interior noise.

Abstract Transient numerical simulations are conducted over a NACA 0012 airfoil with triangular protrusions at a Reynolds number (Re) of 100000 using the γ-Reθ transition Shear Stress Transport (SST) turbulence model. Protrusions of heights 0.5%c, 1%c, and 2%c are placed at one of the three locations, viz, the leading edge (LE), 5%c on the suction surface, and 5%c on the pressure surface, while the angle of attack (AOA) is varied between 0° and 20°. Results obtained from the time-averaged solution of the unsteady Navier-Stokes equation indicate that the smaller protrusion placed at 5%c on the suction surface improves the post-stall lift coefficient by up to 59%, without altering the pre-stall characteristics. The improvement in time-averaged lift coefficients comes with enhanced flow unsteadiness due to vigorous vortex shedding.

Abstract The Naval Nose Landing Gear (NLG) structural assembly consists of components with complex structural geometry and critical functionalities. The landing gear components are subjected to high static and dynamic loads, so they must be appropriately designed, dimensioned, and made by materials with mechanical characteristics that meet high strength, stiffness, and less weight requirements. This article contributes to the shape, size, and material optimization for the NLG of a supersonic naval aircraft for the estimated static loads. The estimated modal frequency values of the NLG assembly using Finite Element Analysis (FEA) software were compared with available Ground Vibration Test data of an aircraft to literally prove the accuracy and suitability of finite element (FE) model that can be used for any further analysis.

Abstract ERRATUM

Abstract From the fact that a propulsor consumes less power for a given thrust if the inlet air is slower, simulations are conducted for a propulsor imposed behind an airfoil as ideal boundary layer ingestion (BLI) propulsor to stand on the benefits of this configuration from the point of view of power and efficiency and to get a closer look on the mutual interaction between them. This interaction is quantified by the impact on three main sets of parameters, namely, power consumption, boundary layer properties, and airfoil performance. The position and size of the propulsor have great influence on the flow around the airfoil. Parametric studies are carried out to understand their influence. BLI propulsor directly affects the power saving and all of the pressure-dependent parameters, including lift and drag. For the present case, power saving reached 14.4% compared to the propeller working in freestream.

Abstract A key problem of the construction of fully electric aircraft is the limited energy density of battery packs. It is generally accepted that this can only be overcome via new, denser battery chemistry together with a further increase in the efficiency of power utilization. One appealing approach for achieving the latter is using laser-assisted filler-based joining technologies, which offers unprecedented flexibility for achieving battery cell connections with the least possible electrical loss. This contribution presents our results on the effect of various experimental and process parameters on the electrical and mechanical properties of the laser-formed bond.

Abstract Improving the energy performance of batteries can increase the reliability of electric aircraft. To achieve this goal, battery management systems (BMS) are required to keep the temperature within the battery pack and cells below the safety limits and make the temperature distribution as even as possible. Batteries have a limited service life as a result of unwanted chemical reactions, physical changes that cause the loss of active materials in the structure, and internal resistance increase during the charging and discharging cycle of the battery. These changes usually affect the electrical performance of batteries. Battery life can be increased only by reducing or preventing unwanted chemical reactions. Lithium-ion (Li-ion) batteries are a suitable option due to their high specific energy and energy density advantages. In this study, the necessity of heat management is emphasized. The discharge tests of the Li-ion battery provided 94.6 Wh under 10C and 90.9 Wh under 1C.

Abstract The range of an aircraft is determined by the amount of energy that its batteries can store. Today, larger batteries are used to increase the range of electric vehicles, although energy efficiency decreases as the weight of the vehicles increases. Among the elements, lithium (Li) is the lightest and has the highest electrochemical potential. Therefore, the use of Li-ion batteries is recommended for hybrid aircraft. In addition, Li-ion batteries are the most common type of battery that is used in portable electronic devices such as smartphones, tablets, and laptops. However, Li-ion batteries may explode due to temperature. Therefore, the thermal analysis of Li-ion batteries was investigated both experimentally and numerically. Li-ion batteries were connected in series (the number is 9). Noboru’s theory of heat generation was discussed in the estimation of energy data.

Abstract A flight envelope for aircraft performance in the vertical plane illustrates the performance limitations on the aircraft, usually indicating the minimum and maximum airspeeds at a given altitude, the airspeeds for maximum rate of climb and maximum angle of climb at a given altitude, and the maximum altitude or absolute ceiling of the aircraft. This study outlines the procedure for constructing a vertical-plane flight performance aircraft for an aircraft with a fixed-pitch propeller, which involves additional complexities due to the variable propeller efficiency. The propeller performance, engine power, and drag polar models are described, as is the computational procedure. Envelopes for the flight performance in the vertical plane are presented for a particular remotely-piloted aircraft at different take-off weights.

Abstract Improving the aerodynamics of heavy trucks is an important consideration in the strive for more energy-efficient vehicles. Cooling drag is one part of the total aerodynamic resistance acting on a vehicle, which arises as a consequence of air flowing through the grille area, the heat exchangers, and the irregular under-hood area. Today cooling packages of heavy trucks are dimensioned for a critical cooling case, typically when the vehicle is driving fully laden, at low speed up a steep hill. However, for long-haul trucks, mostly operating at highway speeds on mostly level roads, it may not be necessary to have all the cooling airflow from an open-grille configuration. It can therefore be desirable for fuel consumption purposes, to shut off the entire cooling airflow, or a portion of it, under certain driving conditions dictated by the cooling demands. In Europe, most trucks operating on the roads are of cab-over-engine type, as a consequence of the length legislations present.

Abstract An investigation into the capability of passive porosity to reduce the drag of a bluff-body is presented. This initial work involves integrating varying degrees of porosity into the side and back faces of a small-scale model to determine optimum conditions for maximum drag reduction. Both force and pressure measurements at differing degrees of model yaw are presented, with the conditions for optimum performance, identified. At a length-based Reynolds number of 2.3 × 106, results showed a maximum drag reduction of 12% at zero yaw when the ratio of the open area on the back face relative to the side faces was between two and four. For all non-zero yaw angles tested, this ratio reduced to approximately two, with the drag benefit reducing to 6% at 10.5 degrees. From a supplementary theoretical analysis, calculated optimum bleed rate into the base for maximum drag reduction, also showed reasonable agreement to other results reported previously.

Abstract Windshield deicing performance is a key metric for HVAC system development and optimization within the sphere of commercial vehicle design. The primary physical parameters that drive this metric are pressure drops in the HVAC ducting, flow rate of the air through the system, and the transient vent temperature rise affected by engine coolant warm-up. However, many design engineers also have to take underhood and instrument panel (IP) space constraints into consideration while trying to optimize a new HVAC system design. This study leverages historical deicing simulation methodologies in conjunction with modern computational horsepower so as to optimize the HVAC ductwork in the studied commercial truck at the beginning of the design phase. By iterating on a design in the computational domain under steady-state and transient flow and thermal conditions, a robust HVAC system design can be created even prior to the prototyping stage of development.