Search Results

The objective of this research is a detailed investigation of multiple injections in a highly-dilute diesel low temperature combustion (LTC) regime. This research concentrates on understanding the performance and emissions benefits of multiple injections via experiments and simulations in a 0.48L signal cylinder light-duty engine operating at 2000 r/min and 5.5 bar IMEP. Controlled experiments in the single-cylinder engine are then combined with three computational tools, namely heat release analysis of measured cylinder pressure, a phenomenological spray model using in-cylinder thermodynamics [1], and KIVA-3V Chemkin CFD computations recently tested at LTC conditions [2]. This study examines the effects of fuel split distribution, injection event timing, rail pressure, and boost pressure which are each explored within a defined operation range in LTC.

The objective of this research is a detailed investigation of unburned hydrocarbon (UHC) in a highly-dilute diesel low temperature combustion (LTC) regime. This research concentrates on understanding the mechanisms that control the formation of UHC via experiments and simulations in a 0.48L signal-cylinder light duty engine operating at 2000 r/min and 5.5 bar IMEP with multiple injections. A multi-gas FTIR along with other gas and smoke emissions instruments are used to measure exhaust UHC species and other emissions. Controlled experiments in the single-cylinder engine are then combined with three computational tools, namely heat release analysis of measured cylinder pressure, analysis of spray trajectory with a phenomenological spray model using in-cylinder thermodynamics [1], and KIVA-3V Chemkin CFD computations recently tested at LTC conditions [2].

A detailed comparison of cylinder pressure derived combustion performance and engine-out emissions is made between an all-metal single-cylinder light-duty diesel engine and a geometrically equivalent engine designed for optical accessibility. The metal and optically accessible single-cylinder engines have the same nominal geometry, including cylinder head, piston bowl shape and valve cutouts, bore, stroke, valve lift profiles, and fuel injection system. The bulk gas thermodynamic state near TDC and load of the two engines are closely matched by adjusting the optical engine intake mass flow and composition, intake temperature, and fueling rate for a highly dilute, low temperature combustion (LTC) operating condition with an intake O2 concentration of 9%. Subsequent start of injection (SOI) sweeps compare the emissions trends of UHC, CO, NOx, and soot, as well as ignition delay and fuel consumption.

This paper investigates flow and combustion in a full-cycle simulation of a four-stroke, three-valve HCCI engine by visualizing the flow with pathlines. Pathlines trace massless particles in a transient flow field. In addition to visualization, pathlines are used here to trace the history, or evolution, of flow fields and species. In this study evolution is followed from the intake port through combustion. Pathline analysis follows packets of intake charge in time and space from induction through combustion. The local scalar fields traversed by the individual packets in terms of velocity magnitude, turbulence, species concentration and temperatures are extracted from the simulation results. The results show how the intake event establishes local chemical and thermal environments in-cylinder and how the species respond (chemically react) to the local field.

An integrated system model containing sub-models for diesel engine, emissions, and aftertreatment devices has been developed. The objective is to study engine-device and device-device interactions. The emissions sub-models used are for NOx and PM (particulate matter) prediction. The aftertreatment sub-models used include a diesel oxidation catalyst (DOC) and a diesel particulate filter (DPF). Controllers have also been developed to allow for transient simulations, active DPF regeneration, and prevention/control of runaway DPF regenerations. The integrated system-level model has been used to simulate DPF regeneration via exhaust fuel injection ahead of the DOC. In addition, the controller model can use intake throttling to assist in active DPF regeneration if needed. Regeneration studies have been done for both steady engine load and with load transients. High to low engine load transients are of particular interest because they can lead to runaway DPF regeneration.

The University of Wisconsin-Madison Snowmobile Team designed and constructed a hybrid-electric snowmobile for the 2005 Society of Automotive Engineers' Clean Snowmobile Challenge. Built on a 2003 cross-country touring chassis, this machine features a 784 cc fuel-injected four-stroke engine in parallel with a 48 V electric golf cart motor. The 12 kg electric motor increases powertrain torque up to 25% during acceleration and recharges the snowmobile's battery pack during steady-state operation. Air pollution from the gasoline engine is reduced to levels far below current best available technology in the snowmobile industry. The four-stroke engine's closed-loop EFI system maintains stoichiometric combustion while dual three-way catalysts reduce NOx, HC and CO emissions by up to 94% from stock. In addition to the use of three way catalysts, the fuel injection strategy has been modified to further reduce engine emissions from the levels measured in the CSC 2004 competition.

This computational study compares predictions and experimental results for the use of direct injected iso-octane fuel during the negative valve overlap (NVO) period to achieve HCCI combustion. The total fuel injection was altered in two ways. First the pre-DI percent, (the ratio of direct injected fuel during the NVO period “pre-DI” to the secondary fuel supplied at the intake manifold “PI”), was varied at a fixed pre-DI injection timing, Secondly the timing of the pre-DI injection was varied while all of the fuel was supplied during the NVO period. A multi-zone, two-dimensional CFD simulation with chemistry was performed using KIVA-3V release 2 implemented with the CHEMKIN solver. The simulations were performed during the NVO period only.

A single cylinder Yamaha research engine was operated with gasoline HCCI combustion using negative valve overlap (NVO). The injection strategy for this study involved using fuel injected directly into the cylinder during the NVO period (pre-DI) along with a secondary injection either in the intake port (PI) or directly into the cylinder (DI). The effects of timing of the pre-DI injection along with the percent of fuel injected during the pre-DI injection were studied in two sets of experiments using secondary PI and DI injections in separate experiments. Results have shown that by varying the pre-DI timing and pre-DI percent the main HCCI combustion timing can be influenced as a result of varied heat release during the negative valve overlap period along with hypothesized varied degrees of reformation of the pre-DI injected fuel. In addition to varying the main combustion timing the ISFC, emissions and combustion stability are all influenced by changes in pre-DI timing and percent.

The University of Wisconsin - Madison Hybrid Vehicle Team has designed, fabricated, tested and optimized a four-wheel drive, charge sustaining, split-parallel hybrid-electric crossover vehicle for entry into the 2006 Challenge X competition. This multi-year project is based on a 2005 Chevrolet Equinox platform. Trade-offs in fuel economy, greenhouse gas impact (GHGI), acceleration, component packaging and consumer acceptability were weighed to establish Wisconsin's Vehicle Technical Specifications (VTS). Wisconsin's Equinox, nicknamed the Moovada, utilizes a General Motors (GM) 110 kW 1.9 L CIDI engine coupled to GM's 6-speed F40 transmission. The rear axle is powered by a 65 kW Ballard induction motor/gearbox powered from a 44-module (317 volts nominal) Johnson Controls Inc., nickel-metal hydride hybrid battery pack. It includes a newly developed proprietary battery management algorithm which broadcasts the battery's state of charge onto the CAN network.

In the current investigation, the authors identified conditions under which increased in-cylinder turbulence can be used to improve diesel emissions. Two separate regimes of engine operation were identified; one in which combustion was constrained by mixing and one in which it was not. These regimes were dubbed under-mixed and over-mixed, respectively. It was found that increasing mixing in the former regime had a profound effect on soot emission. Fuel injection characteristics were found to be extremely important in determining the point at which mixing became inadequate. In addition, the ratio of the fuel injection momentum flux relative to that of the gas injection was found to be important in determining how increasing mixing would effect soot emissions.

Despite promising future, the diesel-dual-fuel engine, with diesel as pilot and natural gas as main, abounds with challenges from high NOx emission and knock especially at high speed and low load. To cope with these challenges, variation of common-rail pressure provides another desirable degree of freedom. Nevertheless, crippling with complicated dynamics, pressure wave inside the transporting rail, disturbance from varying of injections, engine speed variation, and actuator limitation, common-rail pressure control has relied on the simple PID to deliver only marginally satisfactory result. Some attempts to achieve better control have resulted in either too complicated or not too robust control system. We devise a controller from the quantitative feedback theory.

An integrated system model containing sub-models for a multi-cylinder diesel engine, NOx and soot(PM) emissions, diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) has been developed to simulate the engine and aftertreatment systems at transient engine operating conditions. The objective of this work is two-fold; ensure correct implementation of the integrated system level model and apply the integrated model to understand the fuel economy trade-off for various DPF regeneration strategies. The current study focuses on a 1.9L turbocharged diesel engine and its exhaust system. The engine model was built in GT-Power and validated against experimental data at full-load conditions. The DPF model is calibrated for the current engine application by matching the clean DPF pressure drop for different mass flow rates. Load, boost pressure, speed and EGR controllers are tuned and linked with the current engine model.

The University of Wisconsin Hybrid Vehicle Team has implemented and optimized a four-wheel drive, charge sustaining, split-parallel hybrid-electric crossover vehicle for entry into the 2008 ChallengeX competition. This four year project is based on a 2005 Chevrolet Equinox platform. Fuel economy, greenhouse gas impact (GHGI), acceleration, component packaging and consumer acceptability were appropriately weighted to determine powertrain component selections. Wisconsin's Equinox, nicknamed the Moovada, is a split-parallel hybrid utilizing a General Motors (GM) 110 kW 1.9L CDTi (common rail diesel turbo injection) engine coupled to an F40 6-speed manual transmission. The rear axle is powered by a SiemensVDO induction motor/gearbox power-limited to 65 kW by a 40-module (288 volts nominal) Johnson Controls Inc, nickel-metal hydride battery pack.

The University of Wisconsin-Madison Snowmobile Team has designed and constructed a clean, quiet, high performance snowmobile for entry in the 2008 Society of Automotive Engineers' Clean Snowmobile Challenge. Built on a 2003 cross-country touring chassis, this machine features a 750 cc fuel-injected four-stroke engine equipped with a fuel sensor which allows operation ranging from regular gasoline to an 85% blend of ethanol and gasoline (E85). The engine has been customized with a Mototron control system which allows for full engine optimization using a range of fuels from E00 to E85. Utilizing a heated oxygen sensor and a 3-way catalyst customized for this engine by W.C. Heraeus-GmbH, this sled reduces NOx, HC and CO emissions by up to 89% to an average specific mass of 0.484, 0.154, 4.94 g/kW-hr respectively. Finally, the Mototron system also allowed Wisconsin to extract another 4 kW from the Weber 750cc engine; producing 45 kW and 65 Nm of torque.

The diesel/natural gas engine configuration provides a potential alternative solution for PM and NOx emissions reduction from typical diesel engine operations. However, their engine operations suffer from high NMHC/methane emissions and poor engine performance, especially at light loads. By increasing the diesel pilot quantity, the performance and reduction of NMHC/methane emissions can be improved but the emission levels are still very high. Clearly, a typical DOC is not good enough to treat NMHC/methane emissions. Methane has been known as one of most stable species that is difficult to catalytically oxidize in lean burn environment and low exhaust temperatures. An aftertreatment system exclusively designed for treating methane emissions from DDF operations is therefore necessary. The current work is aimed to establish an effective computational tool in order to study the newly proposed catalytic converter system concept on treating methane from DDF operations.

This article presents nondestructive neutron computed tomography (nCT) measurements of Diesel Particulate Filters (DPFs) as a method to measure ash and soot loading in the filters. Uncatalyzed and unwashcoated 200cpsi cordierite DPFs exposed to 100% biodiesel (B100) exhaust and conventional ultra low sulfur 2007 certification diesel (ULSD) exhaust at one speed-load point (1500 rpm, 2.6 bar BMEP) are compared to a brand new (never exposed) filter. Precise structural information about the substrate as well as an attempt to quantify soot and ash loading in the channel of the DPF illustrates the potential strength of the neutron imaging technique.

An investigation of the effect of microflow machining on the spray characteristics of diesel injectors was undertaken. A collection of four VCO injector tips were tested prior to and after an abrasive flow process using a high viscosity media. The injector nozzles were tested on a spray fixture. Rate of injection measurements and high-speed digital images were used for the quantification of the air entrainment rate. Comparisons of the spray characteristics and A/F ratios were made for conditions of before and after the abrasive flow process. Results showed a significant decrease in the injection-to-injection variability and improvement of the spray symmetry. A link between the quantity of air entrained and potential differences in spray plume internal chemical composition and temperature is proposed via equilibrium calculations.

Multi-dimensional computational efforts using comprehensive and skeletal kinetics have been made to investigate the cool flame region in HCCI combustion. The work was done in parallel to an experimental study that showed the impact of the negative temperature coefficient and the cool flame on the start of combustion using different fuels, which is now the focus of the simulation work. Experiments in a single cylinder CFR research engine with n-butane and a primary reference fuel with an octane number of 70 (PRF 70) were modeled. A comparison of the pressure and heat release traces of the experimental and computational results shows the difficulties in predicting the heat release in the cool flame region. The behavior of the driving radicals for two-stage ignition is studied and is compared to the behavior for a single-ignition from the literature. Model results show that PRF 70 exhibits more pronounced cool flame heat release than n-butane.

Simulations of DI Diesel engine combustion have been performed using a modified KIVA-II package with a recently developed phenomenological soot model. The phenomenological soot model includes generic description of fuel pyrolysis, soot particle inception, coagulation, and surface growth and oxidation. The computational results are compared with experimental data from a Cummins N14 single cylinder test engine. Results of the simulations show acceptable agreement with experimental data in terms of cylinder pressure, rate of heat release, and engine-out NOx and soot emissions for a range of fuel injection timings considered. The numerical results are also post-processed to obtain time-resolved soot radiation intensity and compared with the experimental data analyzed using two-color optical pyrometry. The temperature magnitude and KL trends show favorable agreement.

An experimental study was carried out to investigate the effects of fuel injection timing on detailed chemical composition and size distributions of diesel particulate matter (PM) and regulated gaseous emissions in a modern heavy-duty D.I. diesel engine. These measurements were made for two different diesel fuels: No. 2 diesel (Fuel A) and ultra low sulfur diesel (Fuel B). A single-cylinder 2.3-liter D.I. diesel engine equipped with an electronically controlled unit injection system was used in the experiments. PM measurements were made with an enhanced full-dilution tunnel system at the Engine Research Center (ERC) of the University of Wisconsin-Madison (UW-Madison) [1, 2]. The engine was run under 2 selected modes (25% and 75% loads at 1200 rpm) of the California Air Resources Board (CARB) 8-mode test cycle.