Search Results

A single-cylinder, spark-ignited engine was run on a certification test gasoline to saturate the oil in the sump with fuel through exposure to blow-by gas. The sump volume was large relative to production engines making its absorption-desorption time constant long relative to the experimental time. The engine was motored at 1500 RPM, 90° C coolant and oil temperature, and 0.43 bar MAP without fuel flow. Exhaust HC concentrations were measured by on-line FID and GC analysis. The total motoring HC emissions were 150 ppmC1; the HC species distribution was heavily weighted to the low-volatility components in the gasoline. No high volatility components were visible. The engine was then fired on isooctane fuel at the above conditions, producing a total engine-out HC emission of 2300 ppmC1 for Φ = 1.0 and MBT spark timing.

Knock in a HCCI engine was examined by comparing subjective evaluation, recorded sound radiation from the engine, and cylinder pressure. Because HCCI combustion involved simultaneous heat release in a spatially large region, substantial oscillations were often found in the pressure signal. The time development of the audible signal within a knock cycle was different from that of the pressure trace. Thus the audible signal was not the attenuated transmission of the cylinder pressure oscillation but the sound radiation from the engine structure vibration excited by the initial few cycles of pressure oscillation. A practical knock limited maximum load point for the specific 2.3 L I4 engine under test (and arguably for engines of similar size and geometry) was defined at when the maximum rate of cycle-averaged pressure rise reached 5 MPa/ms.

Fuel-air mixing in a direct-injection SI engine was studied to further improve full-load torque output. The fuel-injection location of DI vs. PFI results in different heat sources for fuel evaporation, hence a DI engine has been found to exhibit higher volumetric efficiency and lower knocking tendency, resulting in higher full-load torque output [1]. The ability to change injection timing of the DI engine affects heat transfer and mixture temperature, hence later injection results in lower knocking tendency. Both the higher volumetric efficiency and the lower knocking tendency can improve engine torque output. Improving volumetric efficiency requires that the fuel is injected during the intake stroke. Reducing knocking tendency, in contrast, requires that the fuel is injected late during the compression stroke. Thus, a strategy of split injection was proposed to compromise the two competing requirements and further increase direct-injection SI engine torque output.

Consideration of the heat transfer effects in low-heat-rejection engines has prompted further study into engine heat transfer phenomena. In a previous study, an approximate solution of the one-dimensional energy equation was acquired for transient, compressible, low-Mach number, turbulent boundary layers typical of those found in engines. The current study shows that an approximate solution of the one-dimensional energy equation with arbitrarily-distributed heat release can also be obtained. Using this model, the effects of high temperature walls, combustion, and autoignition on heat transfer can be studied. In the case of high temperature walls, the model predicts the expected behavior unless the quench distance gets very small. For combustion, the reaction must occur close to the wall for a direct effect on the heat transfer to be observed. With autoignition, instantaneous values of heat flux reach levels as high as 6 MW/m2, and oscillate in phase with the pressure wave.

The impact of intake air temperature and humidity on gasoline HCCI engine operation was assessed. The 2.3 L I4 production engine modified for single cylinder operation was controlled by using variable cam phasing on both the intake and exhaust valve in the negative-valve-overlap mode. Exhaust cam phasing was mainly used to control load, and intake cam phasing was mainly used to control combustion phasing. At stoichiometric condition, higher intake air temperature advanced combustion phasing and promoted knock, resulting in a 19% reduction of the Net Indicated Mean Effective Pressure (NIMEP) at the high load limit at 1500 rpm when intake temperature was changed from −10 to 100° C. Higher ambient humidity delayed combustion phasing. For stoichiometric operation, this delay allowed a small extension (a few tenths of a bar in NIMEP) in the high load limit when the moisture concentration was changed from 3 to 30 g/m3 (corresponding to 10-100% relative humidity at 28° C).

An alumina-based LNT is being developed through laboratory studies, for diesel vehicle applications. This LNT provides high NOx conversion efficiency at low temperature (150 to 350°C, especially below 200°C), which is very important for the exhaust-gas after-treatment of diesel passenger vehicles. Addition of 2 to 4 wt% of alkaline-earth metal oxide or other metal oxides to the alumina LNT formulation improves NOx reduction activity at the high end of its active temperature window. More significantly, the alumina-based LNT can undergo the de-SOx process (the process of removing sulfur from the catalytic surfaces) very efficiently: within 1 minute at the relatively low temperature of 500 to 650°C under slightly rich conditions (λ = 0.98 to 0.987). Such a mild de-SOx process imposes minimal thermal exposure, causing almost no thermal damage to the LNT, and helps minimize the associated fuel penalty.

FTP emissions tests on a passenger vehicle equipped with a 1.8 L IDI turbo-charged diesel engine show that the mass emissions of particles decrease by (36±8)% when 16.6% dimethoxymethane (DMM) by volume is added to a diesel fuel. Particle size measurements reveal log-normal accumulation mode distributions with number weighted geometric mean diameters in the 80 - 100 nm range. The number density is comparable for both base fuel and the DMM/diesel blend; however, the distributions shift to smaller particle diameter for the blend. This shift to smaller size is consistent with the observed reduction in particulate mass. No change is observed in NOx emissions. Formaldehyde emissions increase by (50±25)%, while emissions of other hydrocarbons are unchanged to within the estimated experimental error.

The effect of fuel preparation on time-resolved, engine-out hydrocarbon (HC) emissions over a Federal Test Procedure cycle [FTP (75CVS)] for a ULEV vehicle equipped with a 6 cylinder engine has been investigated. Using a single-cone injector, the HC mole fraction in Bag 1 increased by a factor of 3-4 during each of the three accelerations in the first 100 sec after start. No such increases were observed in Bag 3 when the engine was fully warm. The increases during accelerations in Bag 1 were reduced by a factor of 3 when using a Dual-cone fuel injector as a drop-in substitute. The total, tailpipe FTP (75CVS) mass emissions were 25% smaller when using the Dual-cone injector. These results demonstrate that fuel preparation can affect HC emissions from a vehicle very significantly during cold start as has been deduced previously during cold-start tests using a dynamometer-controlled engine.

Homogeneous-charge compression-ignition (HCCI) technology has high potential to significantly reduce fuel consumption and NOx emissions over PFI engines. Control of the HCCI combustion process over the full range of conventional PFI operating conditions, however, has been a challenge. This study describes an HCCI-SI dual-mode engine system proposal based on new approaches to optimize the engine performance. A 0.658L single-cylinder engine was built and tested using these concepts. The engine was operated in HCCI mode from idle to 5.5 bar NMEP and up to 4750 rpm. NSFC in HCCI mode was about 175 g/kWh over most of the operating range except at very low load or near the high load boundary. At a part load of 1500 rpm and an equivalent BMEP of 2.62 bar, net indicated fuel efficiency was 50% higher than PFI engines and 30% higher than a prototype SC-DISI engine.

Stratified-charge DISI engines have been launched in the market by Mitsubishi, Toyota, and Nissan. This paper discusses the current production stratified-charge DISI systems and some alternative systems, including the system using air-forced fuel injection and a proposed system that uses a swirl flow in the piston bowl with a special shape to separate the fuel-rich mixture layer from the wall surface. New DISI concepts are proposed to overcome some drawbacks of current bowl-in-piston type stratified-charge DISI systems. Charge stratification can be realized by using a soft spray with proper spray penetration, droplet size, and cone angle, as shown by CFD simulation results. The drawbacks of fuel wall wetting, soot limited load with charge stratification, large surface to volume ratio, etc., of the bowl-in-piston type system can be minimized.

A single-cylinder OKP (optimized kinetic process) engine, which uses homogeneous-charge compression-ignition (HCCI) technology, was tested, following a previous study, to evaluate the combustion system robustness and to improve the engine performance near the boundaries of the HCCI operating regime at light loads, high loads and high speed. To evaluate the robustness of HCCI combustion control, gasoline fuels with different RON were used, and the engine was tested at different coolant temperatures. It was demonstrated that the proposed HCCI control approaches could control the OKP engine system to operate robustly using different fuels and at different coolant temperatures. The effects of fuel injection timing and residual gas fraction on HCCI combustion and emissions, especially CO emissions and combustion efficiency, were tested at light loads; and the mechanisms were analyzed.

Relationships between radiant emissions, as measured by an in-cylinder optical sensor, and spark-ignition engine combustion parameters are presented for possible use in engine combustion diagnostics and future engine control strategies. A monochromatic gas radiation model, developed in a previous study, was used to derive a series of relationships between the measured radiant emission characteristics and several spark-ignition engine combustion parameters, such as the amplitude and phasing of the peak heat-release rate, combustion duration, IMEP, NOx emission, pressure, trapped mass and exhaust-gas temperature. In addition, many engine parameters of interest can be estimated indirectly from the radiation signal using empirical models. Correlations of air-fuel ratio and exhaust emissions are presented which contain a combination of radiant emission parameters and known base-engine operating parameters, such as intake manifold pressure, etc.

Current demands for high fuel efficiency and low emissions in automotive powerplants have drawn attention to the two-stroke engine configuration. The present study measured trapping and scavenging efficiencies of a firing two-stroke spark-ignition engine by in-cylinder gas composition analysis. Intermediate results of the procedure included the trapped air-fuel ratio and residual exhaust gas fraction. Samples, acquired with a fast-acting electromagnetic valve installed in the cylinder head, were taken of the unburned mixture without fuel injection and of the burned gases prior to exhaust port opening, at engine speeds of 1000 to 3000 rpm and at 10 to 100% of full load. A semi-empirical, zero-dimensional scavenging model was developed based on modification of the non-isothermal, perfect-mixing model. Comparison to the experimental data shows good agreement.

For several years, a single-cylinder, spark-ignited engine without catalyst has been operated at Ford on single-component fuels that are constituents of gasoline as well as on simple fuel mixtures. This paper presents a review of these experiments as well as others pertinent to understanding hydrocarbon emissions. The engine was run at four steady-state conditions which are typical of normal operation. The fuel structure and the engine operating conditions affected both the total HC emissions and the reactivity of these emissions for forming photochemical smog in the atmosphere. These experiments identified major precursor species of the toxic HC emissions benzene and 1,3-butadiene to be alkylated benzenes and either straight chain terminal olefins or cyclic alkanes, respectively. In new data presented, the primary exhaust hydrocarbon species from MTBE combustion is identified as isobutene.

Currently most automotive manufacturers calibrate for rich air/fuel ratios at wide open throttle which produces lower exhaust gas temperatures. Future federal emissions regulations may require less enrichment under these conditions. This study was undertaken to address the question of what happens to engine-out hydrocarbon emissions with different air/fuel ratios at wide open throttle. Tests were run on a single cylinder research engine with a two valve combustion chamber at a compression ratio of 9:1. The test matrix included three air/fuel ratios (10.5, 12.5 and 14.5) and two speeds (1500 and 3000 rpm) at wide open throttle as well as three air/fuel ratios (12.5, 14.6 and 16.5) at a part load condition (1500 rpm, 3.8 bar IMEP). The exhaust was sampled and analyzed for both total and speciated hydrocarbons. The speciation analysis provided concentration data for hydrocarbons present in the exhaust containing twelve or fewer carbon atoms.

The effect of engine operating parameters (speed, spark timing, and fuel-air equivalence ratio [Φ]) on hydrocarbon (HC) oxidation within the cylinder and exhaust system is examined using propane or isooctane fuel. Quench gas (CO2) is introduced at two locations in the exhaust system (exhaust valve or port exit) to stop the oxidation process. Increasing the speed from 1500 to 2500 RPM at MBT spark timing decreases the total, cylinder-exit HC emissions by ∼50% while oxidation in the exhaust system remains at 40% for both fuels. For propane fuel at 1500 rpm, increasing Φ from 0.9 (fuel lean) to 1.1 (fuel rich) reduces oxidation in the exhaust system from 42% to 26%; at 2500 RPM, exhaust system oxidation decreases from 40% to approximately 0% for Φ = 0.9 and 1.1, respectively. Retarded spark increases oxidation in the cylinder and exhaust system for both fuels. Decreases in total HC emissions are accompanied by increased olefinic content and atmospheric reactivity.

Modern four-valve engines are running at ever higher compression ratios in order to improve fuel efficiency. Hotter cylinder bores also can produce increased fuel economy by decreasing friction due to less viscous oil layers. In this study changes in compression ratio and coolant temperature were investigated to quantify their effect on exhaust emissions. Tests were run on a single cylinder research engine with a port-deactivated 4-valve combustion chamber. Two compression ratios (9.15:1 and 10.0:1) were studied at three air/fuel ratios (12.5, 14.6 and 16.5) at a part load condition (1500 rpm, 3.8 bar IMEP). The effect of coolant temperature (66 °C and 108°C) was studied at the higher compression ratio. The exhaust was sampled and analyzed for both total and speciated hydrocarbons. The speciation analysis provided concentration data for hydrocarbons present in the exhaust containing twelve or fewer carbon atoms.

Recent changes in regulatory practices have brought about a need for speciated analysis of the volatile organic components of vehicle exhaust. The purpose of this study was to allow interested laboratories to participate in a Round Robin so that each could assess its speciation methodologies for hydrocarbons, alcohols, and carbonyls. The results from analysis of the liquid samples (methanol, ethanol, and DNPH-derivatives of carbonyls) were reported in SAE 941944. For gaseous hydrocarbon samples, two gasolines from the Auto/Oil Air Quality Improvement Research Program (AQIRP) were used to prepare compressed gas cylinders of “synthetic exhaust.” These samples were also doped with typical light hydrocarbon combustion components, marker compounds, and MTBE (in one of the two sets of samples). The cylinders were circulated to 16 laboratories, which included automotive and petroleum companies, contract laboratories, and regulatory agencies.

Absorption of fuel in engine oil layers has been shown to be a possible source of hydrocarbon (HC) emissions from spark-ignited engines. However, the magnitude of this source in a normally operating engine has not been determined unambiguously. In these experiments, a series of n-alkanes of widely different solubility (n-hexane through undecane) was added (1.5 wt % each) to a Base gasoline (CA Phase 2). Steady-state experiments were carried out at two coolant temperatures (339 and 380 K) using a single-cylinder engine with the combustion chamber of a production V-8. Both total and speciated engine-out HC emissions were measured. The emissions indices of the heavier dopants did not increase relative to hexane at either coolant temperature.

Total and speciated, engine-out, hydrocarbon (HC) emissions have been measured as a function of time after a 23°C cold start of a gasoline-fueled, V-8 engine. Hydrocarbon emissions from two fuel injection systems were compared: a production port-fuel-injection (PFI) system; and a pre-vaporized (heated) central-fuel-injection (PV-CFI) system. The results indicate that, for this particular engine at the chosen operating conditions, the effect of fuel preparation on HC emissions during cold start is minimal at low load (2.57 bar IMEP (gross), MAP = 0.34 bar) but becomes significant at higher load (5.15 bar IMEP, MAP = 0.58 bar) early in the cold start. Comparison of the relative contribution to the exhaust HC of a series of fuel-derived alkanes suggests that fuel absorption in oil films is a minor contributor to HC emissions from this engine during a 23°C cold start.