This procedure is intended to apply to fuel pumps. This procedure will be defined in terms of recommended test fluid, test setup, test conditions, and test method. This procedure may be used for other fuel system components, by testing in conjunction with the pump, which normally supplies the component inlet flow, or a substitute test pump of similar capacity. This procedure may be used, with variations in test conditions and test fluid for performing pump evaluation tests. Tests at progressively increasing pump speeds and pressures will provide design limitation data. Alternate test periods on a test pump and another pump, of a design for which actual service durability is known, will provide useful comparison data.
This SAE Aerospace Recommended Practice (ARP) establishes the requirements for lubricating oil filters for general aviation reciprocating engine applications with lubricating oil systems normally operating in a pressure range of 345 to 689 kPa (50 to100 psig).
This ARP delineates two complementary filter element performance ratings and corresponding test procedures. It is intended for the noncleanable (disposable), fine fuel filter elements used in aviation gas turbine engine systems.
This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance ratings: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements used in aviation gas turbine engine systems.
This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance parameters: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements, rated at 25 µm(c) or finer, used in aviation gas turbine engine fuel systems.
This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance ratings: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements used in aviation gas turbine engine fuel systems.
This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance ratings: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements used in aviation gas turbine engine fuel systems.
This SAE Aerospace Information Report (AIR) discusses the sources of Copper in aviation jet fuels, the impact of Copper on thermal stability of jet fuels and the resultant impact on turbine engine performance, and potential methods for measurement and reduction of the catalytic activity of Copper contamination in jet fuels. This document is an information report and does not provide recommendations or stipulate limits for Copper concentrations in jet fuels.
This procedure is intended to apply to fuel pumps. This procedure will be defined in terms of recommended test fluid, test setup, test conditions, and test method. This procedure may be used for other fuel system components, by testing in conjunction with the pump, which normally supplies the component inlet flow, or a substitute test pump of similar capacity. This procedure may be used, with variations in test conditions and test fluid for performing pump evaluation tests. Tests at progressively increasing pump speeds and pressures will provide design limitation data. Alternate test periods on a test pump and another pump, of a design for which actual service durability is known, will provide useful comparison data.
This SAE Aerospace Information Report (AIR) reviews performance testing parameters for non-cleanable (often referred to as disposable) filter elements utilized in aircraft power and propulsion lubrication systems, including gas turbine engines and auxiliary power units (APUs), propulsion and transmission gear boxes, and constant speed drives and integrated drive generators (IDGs). This document is confined to laboratory testing of filter element performance to qualify the filtration medium and filter element construction as opposed to qualification of the complete filter assembly. The testing discussed here is usually followed by laboratory and on-engine testing of the entire lube filter assembly (including filter element, housing, valving, etc.), which is outside the scope of this AIR.
This SAE Aerospace Information Report (AIR) reviews performance testing parameters for non-cleanable, often referred to as disposable, filter elements utilized in aircraft power and propulsion lubrication systems, including gas turbine engines, propulsion and transmission gear boxes, and constant speed drives and integrated drive generators.
This SAE Aerospace Information Report (AIR) reviews performance testing parameters for non-cleanable, often referred to as disposable, filter elements utilized in aircraft power and propulsion lubrication systems, including gas turbine engines and auxiliary power units (APUs), propulsion and transmission gear boxes, and constant speed drives and integrated drive generators (IDGs). This document is confined to laboratory testing of filter element performance to qualify the filtration medium and filter element construction as opposed to qualification of the complete filter assembly. The testing discussed here is usually followed by laboratory and on-engine testing of the entire lube filter assembly (including filter element, housing, valving, etc.), which is outside the scope of this AIR.
The AIR is limited to a presentation of the historical background, the technical rationale which generated the V/L fuel condition interface requirement in specifications between the aircraft fuel delivery system and the aircraft engine fuel system, and limitations in the usage of the V/L concept.
The AIR is limited to a presentation of the historical background, the technical rationale which generated the V/L fuel condition interface requirement in specifications between the aircraft fuel delivery system and the aircraft engine fuel system, and limitations in the usage of the V/L concept.
This SAE Aerospace Recommended Practice (ARP) describes the multi-pass method for evaluating the filtration performance of fine lube filter elements, commonly utilized in aerospace power and propulsion lubrication systems: gas turbine engines, auxiliary power units (APUs), helicopter transmissions, constant speed drives (CSDs), and integrated drive generators (IDGs).
This SAE Aerospace Recommended Practice (ARP) describes the multi-pass method for evaluating the filtration performance of fine lube filter elements, commonly utilized in aerospace power and propulsion lubrication systems: gas turbine engines, auxiliary power units (APUs), helicopter transmissions, constant speed drives (CSDs), and integrated drive generators (IDGs).
This SAE Aerospace Recommended Practice (ARP) describes the multi-pass method for evaluating the filtration performance of fine lube filter elements, commonly utilized in aerospace power and propulsion lubrication systems: gas turbine engines, auxiliary power units (APUs), helicopter transmissions, constant speed drives (CSDs), and integrated drive generators (IDGs).
This SAE Aerospace Recommended Practice (ARP) describes the multi-pass method for evaluating the filtration performance of fine lube filter elements, commonly utilized in aerospace power and propulsion lubrication systems: gas turbine engines, auxiliary power units (APUs), helicopter transmissions, constant speed drives (CSDs), and integrated drive generators (IDGs).
This document establishes requirements, test procedures, and acceptance criteria for the fire testing of fluid handling components and materials used in aircraft fluid systems. It is applicable to fluid handling components other than those prescribed by AS1055 (e.g., hoses, tube assemblies, coils, and fittings). It also is applicable to materials, wiring, and components such as reservoirs, valves, gearboxes, pumps, filter assemblies, accumulators, fluid-cooled electrical/electronic components, in-flight fluid system instrumentation, hydromechanical controls, actuators, heat exchangers, and manifolds. These components may be used in fuel, lubrication, hydraulic, or pneumatic systems.