Search Results

In this work a multilevel CFD analysis have been applied for the design of an intake air-box with improved characteristics of noise reduction and fluid dynamic response. The approaches developed and applied for the optimization process range from the 1D to fully 3D CFD simulation, exploring hybrid approaches based on the integration of a 1D model with quasi-3D and 3D tools. In particular, the quasi-3D strategy is exploited to investigate several configurations, tailoring the best trade-off between noise abatement at frequencies below 1000 Hz and optimization of engine performances. Once the best configuration has been defined, the 1D-3D approach has been adopted to confirm the prediction carried out by means of the simplified approach, studying also the impact of the new configuration on the engine performances.

In the next years, the upcoming emission legislations are expected to introduce further restrictions on the admittable level of pollutants from vehicles measured on homologation cycles and real drive tests. In this context, the strict control of pollutant emissions at the cold start will become a crucial point to comply with the new regulation standards. This will necessarily require the implementation of novel strategies to speed-up the light-off of the reactions occurring in the after-treatment system, since the cold start conditions are the most critical one for cumulative emissions. Among the different possible technological solutions, this paper focuses on the evaluation of the potential of a burner system, which is activated before the engine start. The hypothetical burner exploits the lean combustion of an air-gasoline mixture to generate a high temperature gas stream which is directed to the catalyst section promoting a fast heating of the substrate.

The selective catalytic reduction has seen widespread adoption as the best technology to reduce the NOx emissions from internal combustion engines, particularly for Diesels. This technology uses ammonia as a reducing agent, which is obtained injecting an ammonia carrier into the exhaust gas stream. The dosing of the ammonia carrier, usually AdBlue, is the major concern during the design and engine calibration phases, since the interaction between the injected liquid and the components of the exhaust system can lead to the undesired formation of solid deposits. To avoid this, the thermal and kinematic interaction between the spray and the components of the after treatment system (ATS) must be modeled accurately. In this work, the authors developed a Conjugate Heat Transfer (CHT) framework to model the kinetic and thermal interaction among the spray, the eventual liquid layer and the pipe walls.

Nowadays quasi-3D approaches are included in many commercial and research 1D numerical codes, in order to increase their simulation accuracy in presence of complex shape 3D volumes, e.g. plenums and silencers. In particular, these are regarded as valuable approaches for application during the design phase of an engine, for their capability of predicting non-planar waves motion and, on the other hand, for their low requirements in terms of computational runtime. However, the generation of a high-quality quasi-3D computational grid is not always straightforward, especially in case of complex elements, and can be a time-consuming operation, making the quasi-3D tool a less attractive option. In this work, a quasi-3D module has been implemented on the basis of the open-source CFD code OpenFOAM and coupled with the 1D code GASDYN.

In the last decades numerical simulations have become reliable tools for the design and the optimization of silencers for internal combustion engines. Different approaches, ranging from simple 1D models to detailed 3D models, are nowadays commonly applied in the engine development process, with the aim to predict the acoustic behavior of intake and exhaust systems. However, the acoustic analysis is usually performed under the hypothesis of infinite stiffness of the silencer walls. This assumption, which can be regarded as reasonable for most of the applications, can lose validity if low wall thickness are considered. This consideration is even more significant if the recent trends in the automotive industry are taken into account: in fact, the increasing attention to the weight of the vehicle has lead to a general reduction of the thickness of the metal sheets, due also to the adoption of high-strength steels, making the vibration of the components a non negligible issue.

In this work an integration between a 1D code (Gasdyn) with a CFD code (OpenFOAM®) has been applied to improve the performance of a Moto3TM engine. The four-stroke, single cylinder S.I. engine was modeled, in order to predict the wave motion in the intake and exhaust systems and study how it affects the cylinder gas exchange process. The engine considered was characterized by having an air induction system with integrated filter cartridge, air-box and intake runner, resulting in a complex air-path form the intake mouth to the intake valves, which presents critical aspects when a 1D modeling is addressed. This paper presents a combined and integrated simulation, in which the intake systems was modeled as a 3D geometry whereas the exhaust system, which presented a simpler geometry, was modeled by means of a 1D approach.

Metallic foams or sponges are materials with a cell structure suitable for many industrial applications, such as reformers, heat catalytic converters, etc. The success of these materials is due to the combination of various characteristics such as mechanical strength, low density, high specific surface, good thermal exchange properties, low flow resistance and sound absorption. Different materials and manufacturing processes produce different type of structure and properties for various applications. In this work a genetic algorithm has been developed and applied to support the design of catalytic devices. In particular, two substrates were considered, namely the traditional honeycomb and an alternative open-cell foam type. CFD simulations of pressure losses and literature based correlations for the heat and mass transfer were used to support the genetic algorithm in finding the best compromise between flow resistance and pollutant abatement.

Selective Catalytic Reduction (SCR) systems are nowadays widely applied for the reduction of NOx emitted from Diesel engines. The typical process is based on the injection of aqueous urea in the exhaust gases before the SCR catalyst, which determines the production of the ammonia needed for the catalytic reduction of NOx. However, this technology is affected by two main limitations: a) the evaporation of the urea water solution (UWS) requires a sufficiently high temperature of the exhaust gases and b) the formation of solid deposits during the UWS evaporation is a frequent phenomenon which compromise the correct operation of the system. In this context, to overcome these issues, a technology based on the injection of gaseous ammonia has been recently proposed: in this case, ammonia is stored at the solid state in a cartridge containing a Strontium Chloride salt and it is desorbed by means of electrical heating.

In the last few years, the effect of diabatic test conditions on compressor performance maps has been widely investigated, leading some Authors to propose different correction models. The accuracy of turbocharger performance map constitute the basis for the tuning and validation of a numerical method, usually adopted for the prediction of engine-turbocharger matching. Actually, it is common practice in automotive applications to use simulation codes, which can either require measured compression ratio and efficiency maps as input values or calculate them “on the fly” throughout specific sub-models integrated in the numerical procedures. Therefore, the ability to correct the measured performance maps taking into account internal heat transfer would allow the implementation of commercial simulation codes used for engine-turbocharger matching calculations.

The effects of the internal geometry of catalytic converter channels on flow characteristics; exhaust backpressure and overall conversion efficiency have been investigated by means of both numerical simulations and experimental investigations. The numerical work has been carried out by means of a micro scale numerical tool specifically tailored for flow characteristics within converter channels. The results are discussed with aid of flow distribution patterns within the single cell and backpressure figures along the catalyst channel. The results of the numerical investigation provide information about the most efficient channel shapes. An experimental validation of the simulated results has been carried out with a production 3.6 liter, 6-cylinder engine on a dynamic test bench. Both modal and bag emission data have been measured during the FTP-Cycle.

In this work an integration between a 1D code (Gasdyn) with a CFD code (OpenFOAM®) has been applied to improve the performance of a Moto3 engine. The four-stroke, single cylinder S.I. engine was modeled, in order to predict the wave motion in the intake and exhaust systems and to study how it affects the cylinder gas exchange process. The engine considered was characterized by having an air induction system with integrated filter cartridge, air-box and intake runner, including two fuel injectors, resulting in a complex air-path from the intake mouth to the intake valves, which presents critical aspects when a 1D modeling is addressed. The exhaust and intake systems have been optimized form the point of view of the wave action. However, due to the high revolution speed reached by this type of engine, the interaction between the gas stream and the fuel spray becomes a key aspect to be addressed in order to achieve the best performance at the desired operating condition.

It is well known that the optimal management of cold start is crucial to fulfill present and future emission legislation. During past years the catalytic converter has left its original under floor position to get increasingly closer to the engine in order to exploit higher exhaust gas temperature. Simultaneously, the exhaust gas temperature is becoming significantly lower, both in gasoline engines due to the extensive use of turbo charging, and in diesel engines thanks to very high combustion efficiency and in some cases the use of two stage turbo charging. A well established way to reach the catalyst light-off temperature fast enough to fulfill emission limits consists of artificially increasing the exhaust gas temperature. This has the drawback of a higher fuel consumption which conflicts with the tight CO2 targets now required of the OEMs.

In the last years, as a response to the more and more restrictive emission legislation, new devices (SRC, DOC, NOx-trap, DPF) have been progressively introduced as standard components of modern after-treatment system for Diesel engines. In addition, the adoption of electrical heating is nowadays regarded with interest as an effective solution to promote the light-off of the catalyst at low temperature, especially at the start-up of the engine and during the low load operation of the engine typical of the urban drive. In this work, a state-of-the-art 48 V electrical heated catalyst is considered, in order to investigate its effect in increasing the abatement efficiency of a standard DOC. The electrical heating device considered is based on a metallic support, arranged in a spiral layout, and it is heated by the Joule effect due to the passage of the electrical current.

Recent engine development has been mainly driven by increased specific volumetric power and especially by fuel consumption minimization. On the other hand the stringent emission limits require a very fast cold start that can be reached only using tailored catalyst heating strategy. This kind of thermal management is widely used by engine manufactures although it leads to increased fuel consumption. This fuel penalty is usually higher for high power output engines that have a very low load during emission certification cycle leading to very low exhaust gas temperature and, consequently, the need of additional energy to increase the exhaust gas temperature is high. An alternative way to reach a fast light off minimizing fuel consumption increase is the use of an Electrical Heated Catalyst (EHC) that uses mechanical energy from the engine to generate the electrical energy to heat up the catalyst.

Future stringent emission limits both in the European Community and USA require continuously increased conversion efficiency of exhaust after-treatment systems. Besides the obvious targets of fastest light-off performance, overall conversion efficiency and durability, catalytic converters for maximum output engines require highly optimized flow properties as well, in order to create minimum exhaust backpressure for low fuel consumption. This work deals with the design, development and serial introduction of a close coupled main catalyst system using the innovative technology of Perforated Foils (PE). By means of PE-technology, channel-to-channel gas mixing within the metal substrate could be achieved leading to dramatically reduced backpressure values compared with the conventional design.

Future emission legislation can be met through substantial improvement in the effectiveness of the exhaust gas after-treatment system, the engine and the engine management system. For the catalytic converter, differentiation is necessary between the cold start behavior and the effectiveness at operating temperature. To be catalytically effective, a converter must be heated by the exhaust gas up to its light-off temperature. The major influential parameter for the light-off still is the supply of heat from the exhaust gas. Modification of the cold start calibration of engine control such as spark retard or increased idle speed can increase the temperature level of the exhaust gas. One further possibility is represented by a reduction of the critical mass ahead of the catalyst (exhaust manifold and pipe). Nevertheless the best measure to obtain optimal cold start effectiveness still seems to be locating the converter close to the engine.

Modern Diesel Engines equipped with Common-Rail Direct Injection, EGR and optimized combustion technology have been proven to reduce dramatically engine raw emissions both in terms of Nox and Particulate Matter. As a matter of fact the recently introduced FIAT 1.3 JTD 4 Cylinder Engine achieves Euro 4 limits with aid of conventional 2-way oxidation catalyst. Nevertheless some special applications, such as platforms with relatively higher gross vehicle weight possibly yield to PM-related issues. The present paper deals with the development program carried out to design a cost effective aftertreatment solution in order to address particulate matter tailpipe emissions. The major constraint of this development program was the extremely challenging packaging conditions and the absolute demand to avoid any major impact on the system design. The flow-through metal supported PM Filter Catalyst has been extensively tested on the specific vehicle application with aid of roller bench setup.

Future stringent emission levels for NOx and PM will lead to the introduction of innovative combustion processes for diesel engines, such as premixed combustion, with the results to enhance the engine out emission of HC and CO. Therefore very efficient oxidation catalyst will be needed to face this possible issue. This paper deals with the optimization of a EU IV exhaust system by means of innovative metal supported catalyst, as for example the Pre Turbo Catalyst and the Hybrid Catalyst in combination with dedicated catalyst coatings. Moreover a base study over the use of PM-Filter Catalyst has been made, to show the efficiency of such a device with EU IV engine calibration. The second part of the paper deals with the turbulent like structured foils substrates to have an even more efficient diesel oxidation catalyst with very high volumetric efficiency.

Increasing demands on the capabilities of engine simulation and the ability to accurately predict both performance and acoustics has lead to the development of several numerical tools to help engine manufacturers during the prototyping stage. The aid of CFD tools (3D and 1D) can remarkably reduce the duration and the costs of this stage. The need of achieving good accuracy, along with acceptable computational runtime, has given the spur to the development of a geometry based quasi-3D approach. This is designed to model the acoustics and the fluid dynamics of both intake and exhaust system components used in internal combustion engines. Models of components are built using a network of quasi-3D cells based primarily on the geometry of the system. The solution procedure is based on an explicitly time marching staggered grid approach making use of a flux limiter to prevent numerical instabilities.

Turbocharging is playing today a fundamental role not only to improve automotive engine performance, but also to reduce fuel consumption and exhaust emissions for both Spark Ignition and Diesel engines. Dedicated experimental investigations on turbochargers are therefore necessary to assess a better understanding of its performance. The availability of experimental information on turbocharger steady flow performance is an essential requirement to optimize the engine-turbocharger matching, which is usually achieved by means of simulation models. This aspect is even more important when referred to the turbine efficiency, since its swallowing capacity can be accurately evaluated through the measurement of mass flow rate, inlet temperature and pressure ratio across the machine.