Search Results

The investigations into the emissions from light-duty vehicles are carried out on a chassis dynamometer in the NEDC test in Europe and FTP75 test in the US. Such tests do not entirely reflect the real road conditions. It should be noted that the changes in the methodology of emissions testing should go in the direction where they get closer to the actual road conditions. The paper presents the road test results obtained in an urban congested areas. The analysis of the road tests results (exhaust emissions and fuel consumption) was carried out considering the road conditions (vehicle speed and acceleration). The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. For these measurements a portable SEMTECH DS analyzer by SENSORS, Particle Counter by AVL and Particle Seizer EEPS by TSI has been used.

Due to a rapid development of air transportation there is a need for the assessment of real environmental risk related to the aircraft operation. The emission of carbon monoxide and particulate matter is still a serious threat~constituting an obstacle in the development of combustion engines. The applicable regulations related to the influence of the air transportation on the environment introduced by EPA (Environmental Protection Agency), ICAO (International Civil Aviation Organization) contained in JAR 34 (JAA, Joint Aviation Requirements, JAR 34, Aircraft Engine Emissions), FAR 34 (FAA, Federal Aviation Regulations, Part 34, Fuel Venting and Exhaust Emission Requirements for Turbine Engine Powered Airplanes), mostly pertain to the emission of noise and exhaust gas compounds, NOx in particular. They refer to jet engines and have stationary test procedures depending on the engine operating conditions.

The article shows the results of particulate matter emissions obtained in the ESC cycle. In order to carry out the tests different devices were applied for the measurement of particular matter (AVL Smart Sampler - measurement by means of a gravimetric method of a partial exhaust smoke dilution, Horiba Mexa 1220 PM - measurement with the use of two flame ionizing detectors), which were then compared to the smokiness values (AVL 415 - measurement of exhaust smoke values, Opacimetr 439 - measurement of exhaust opacity). Having compared the obtained correlation results, main relationships of fractional composition of particular matter, obtained in the tests, were defined.

In order to measure the concentration of toxic compounds a mobile analyzer for toxic tests SEMTECH DS by SENSORS Inc. was used. In the study the results of the vehicle emission tests in the road conditions were presented as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the harmful compound emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of emission intensity.

The paper addresses the problem of toxic emission from non-road vehicles. The paper presents the results of the investigations and analyses related to the engine operating conditions of a selected group of non-road vehicles. The presented tests have been carried out on a large groups of vehicles - several from each representative group. This was chiefly on-site construction machinery (dump tracks, excavators, bulldozers) used in the construction of the motorway and as an auxiliary equipment in an open-cast mine. An analysis has been performed based on which a range of the most frequently used loads and engine speeds was determined. The obtained time density characteristics (distribution of speeds and loads in time) of the engines was compared to the measuring points of the toxic emission homologation cycle.

In order to measure the concentration of exhaust a mobile analyzer SEMTECH DS by SENSORS Inc and particle matter by TSI was used. In the study the results of the vehicle emission tests in the road conditions were presented as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of emission intensity.

In order to measure the concentration of exhaust emissions a mobile emission testing analyzer SEMTECH DS by SENSORS Inc was used. In the study the results of the vehicle emission tests in the road conditions were presented, as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle in motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of the emission intensity.

The paper presents the results of the investigations of an armored modular vehicle 8x8 Rosomak fitted with a diesel engine during start and warm-up. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of exhaust emission at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption have also been carried out under static conditions, during startup and at constant engine speed without engine load. For the measurement of the engine operating conditions and the fuel consumption a diagnostic vehicle system was used.

The tests related to the exhaust emissions from non-road vehicles are currently performed on a chassis dynamometer under the name of NRSC (ISO 8178) and NRTC. In light of the growing requirements related to the environment protection in transport the authors recommend determining the exhaust emissions through real vehicle operating conditions. The tests carried out under real operating conditions could be used for the process of optimization of future power trains of regular road vehicles and non-road vehicles. What is more, these tests should be taken into account in the works on the changes of the legislation related to the emission limits from combustion engines. The paper presents the results of the tests on the exhaust emissions from an agricultural harvester engine and a tractor engine in real operating conditions. The harvester operation during the test consisted in crops collection from the field and the tractor operation during the test consisted in plowing.

The motor vehicle is one of the main sources of pollutant emissions, especially in urban areas. Environmentally friendly fuels are regarded as very effective means to decrease emissions. With regard to diesel engines, the reduction in nitrogen oxides and particulates are major problem areas. Although the fuel influence on NOx is comparatively low, the composition and parameters of diesel fuel have a big influence on particulate emissions and composition. Sulphur content is one of fuel proprieties, which has the most considerable influence on particulates. This paper describes results of the research on particulate emissions from diesel engines fuelled with research fuels of differing sulphur content. The sulphur content of the research fuels varied from 2000 ppm through 350 ppm (EURO III) and 50 ppm (EURO IV limit, which will be in force in the European Community from 1 January 2005) up to less than 5 ppm.

The great reduction in future diesel engine emission limits, especially PM and NOx, forces one to develop means to comply with stringent legislation. Environmentally friendly fuels are regarded as a very effective means to decrease emissions. Although the emission reduction is less than could be achieved by the most modern engine technology or alternative fuels, the immediate net effect of reformulated diesel fuel on emissions is significant, as it takes place over the whole vehicle population. The experimental results presented in this paper were obtained within a research program investigating the effect of different fuels upon emissions from compression-ignition automotive engines. The research were carried out in the laboratories of the BOSMAL Automotive R & D Centre in co-operation to Institute of Internal Combustion Engines at Poznan University of Technology. The partial results of this research program were presented in SAE Paper 2002-01-2219.

The paper presents the results of tests on a combustion engine of an armored modular vehicle 8x8 Rosomak under combat simulating conditions. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of toxic compounds at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption were performed under the conditions of combat simulation and in the overboost mode. Based on the obtained results, an analysis of the engine and vehicle operation was performed and the on-road and unit exhaust emissions as well as on-road and unit fuel consumption were compared.

The paper discusses the measurement of the PM emissions from non-road vehicles (a farm tractor and an excavator) under actual operating conditions. Full exploration of the relations between the operating parameters of these vehicles and their emissions requires measurements under actual conditions of their operation. The specificity of the emission measurements, PM in particular, requires technologically advanced measuring devices. The situation gets even more complicated if, beside the PM mass, we also wish to obtain the PM size distribution and particle number (PN). One of the more important technical issues is the difficulty in fitting of the measurement equipment in/on the vehicle in operation (e.g. a farm tractor). That is the reason why the investigations were carried out in a laboratory. The laboratory technicians applied load to the engines through external devices - a hydraulic system for the excavator and a brake coupled to the farm tractor power takeoff.

The paper presents an analysis of the emission level from a heavy-duty truck of the GVW of 12,000 kg. The exhaust emission tests were performed under actual traffic conditions in the area of Poznań. For the tests portable exhaust emission analyzers SEMTECH DS and AVL Micro Soot Sensor were used. The characteristics of the exhaust emission components have been determined in relation to the engine speed and load as well as vehicle parameters (speed and acceleration). The paper includes an analysis of the engine operating conditions as well as the range of engine speeds and engine loads. The vehicle fuel consumption was also determined through the carbon balance method. Based on the obtained values of the emission of CO, NOx and PM, the emission indexes were determined that provided information on the relation of the measured emissions to the levels specified in the EEV standard. The emissions of all the exhaust components, except NOx were lower than the EEV limits.

This paper discusses the legislative situation regarding type approval of plug-in hybrid vehicles (also known as off-vehicle charging hybrid-electric vehicles, OVC-HEV) in the range of exhaust emissions and fuel consumption. A range of tests were conducted on two Euro 6d-complaint OVC-HEVs to quantify emissions. Procedures were based on EU legislative requirements. For laboratory (chassis dyno) testing, two different test cycles and three different ambient temperatures were used for testing. Furthermore, in some cases additional measurements were performed, including measurement of emissions of particulate matter and continuous analysis of regulated and unregulated pollutants in undiluted exhaust. Consumption of electrical energy was also monitored. On-road testing was conducted on the test vehicle tested on the chassis dyno in the tests mentioned above, as well as on a second OVC-HEV test vehicle.

The paper describes the measurement of PM emission from an excavator engine under actual operating conditions. The exploration of the relations between the engine operating parameters and its emissions requires measurements under actual conditions of engine operation. The specificity of the emission measurements, PM in particular, requires technologically advanced measuring devices. The situation gets even more complicated when, beside the PM mass. The particle size distribution and number (PN) also need to be measured. An important technical issue is the difficulty in fitting the measurement equipment in/on the vehicle in operation (e.g. excavator), which is why the presented investigations were carried out in a laboratory under simulated operation. The laboratory technicians applied load to the engines through the excavator hydraulic system.