Search Results

A detailed investigation of the influence of anisotropic hardening models on drawbead restraining force is presented in this paper. The recently modified Yoshida model is adopted to characterize the anisotropic hardening behavior for steels. A two-dimensional drawbead model is used and the restraining forces corresponding to several different bead penetrations are obtained and compared against experimental results. The comparison of the predicted results for the Modified Yoshida Model with isotropic hardening models indicates that the anisotropic hardening gives lower drawbead restraining forces in general. The impact of hardening models on springback is also presented, and it's demonstrated that the springback amount predicted by the modified Yoshida model is much closer to the experimental data than that predicted by conventional isotropic hardening model.

Design optimization techniques are widely used to drive designs toward a global or a near global optimal solution. However, the achieved optimal solution often appears to be the only choice that an engineer/designer can select as the final design. This is caused by either problem topology or by the nature of optimization algorithms to converge quickly in local/global optimal or both. Problem topology can be unimodal or multimodal with many local and/or global optimal solutions. For multimodal problems, most global algorithms tend to exploit the global optimal solution quickly but at the same time leaving the engineer with only one choice of design. The paper explores the application of genetic algorithms (GA), simulated annealing (SA), and mixed integer problem sequential quadratic programming (MIPSQP) to find multiple local and global solutions using single objective optimization formulation.

The effect of temperature and preload on the bolt load retention (BLR) behavior of AZ91D and AE42 magnesium die castings was investigated. The results were compared to those of 380 aluminum die castings. Test temperatures from 125 to 175°C and preloads from 7 to 28 kN were investigated. The loss of preload for AZ91D was more sensitive to temperature than that observed for AE42, especially at low preloads. In general, retained bolt-load was lowest in AZ91D. All test assemblies were preloaded at room temperature and load levels increased when the assemblies reached test temperature. The load-increase was dependent on the preload level, test temperature, alloy, and results from thermal expansion mismatch between the steel bolt and the magnesium alloy components, mitigated by the onset of primary creep. Thermal exposure (aging) of AZ91D at 150°C improved BLR behavior.

Creep-resistant magnesium alloys for automotive powertrain applications offer significant potential for vehicle weight reduction. In this study permanent mold casting, microstructure and creep behavior have been investigated for a series of ternary magnesium alloys (Mg-4Al-4X (X: Ca, Ce, La, Sr) wt%) and AXJ530 (Mg-5Al-3Ca-0.15Sr, wt%). A permanent mold was instrumented with twelve thermocouples and mold temperature was monitored during the casting process. Average mold temperature increased from 200°C to 400°C during a typical alloy casting series (fifteen to twenty castings). The cast microstructure for all alloys consists of primary α-Mg globular phase surrounded by eutectic structure which is composed of intermetallic(s) and α-Mg magnesium phases. The primary cell size of the AXJ530 increased from 18 to 24 μm with increasing mold temperature and a similar trend is expected for all alloys.

Finite element analysis (FEA) predictions of magnesium beams are compared to load versus displacement test measurements. The beams are made from AM60B die castings, AM30 extrusions and AZ31 sheet. The sheet and die cast beams are built up from two top hat sections joined with toughened epoxy adhesive and structural rivets. LS-DYNA material model MAT_124 predicts the magnesium behavior over a range of strain rates and accommodates different responses in tension and compression. Material test results and FEA experience set the strain to failure limits in the FEA predictions. The boundary conditions in the FEA models closely mimic the loading and constraint conditions in the component testing. Results from quasi-static four-point bend, quasi-static axial compression and high-speed axial compression tests of magnesium beams show the beam's behavior over a range of loadings and test rates. The magnesium beams exhibit significant material cracking and splitting in all the tests.

Magnesium alloy extrusions offer potentially more mass saving compared to magnesium castings. One of the tasks in the United States Automotive Materials Partnership (USAMP) ?Magnesium Front End Research and Development? (MFERD) project is to evaluate magnesium extrusion alloys AM30, AZ31 and AZ61 for automotive body applications. Solid and hollow sections were made by lowcost direct extrusion process. Mechanical properties in tension and compression were tested in extrusion, transverse and 45 degree directions. The tensile properties of the extrusion alloys in the extrusion direction are generally higher than those of conventional die cast alloys. However, significant tension-compression asymmetry and plastic anisotropy need to be understood and captured in the component design.

A demonstration structure was cast in AM60. The structure, known as the Generic Frame Casting or GFC, was designed specifically to mimic features seen in castings for closure applications. Excised samples were subsequently removed from different areas of the casting and tested under axial loading conditions. Component level tests were also conducted. Comparison of the excised sample results and the component level testing indicated the influence of local properties on the component level deformation. It was shown that varying the casting processing conditions could change the local ductility and yield strength in different areas of casting with the same geometry. Lowering the local ductility decreased the total displacement in a component level test and lowered the amount of energy absorption. Therefore, understanding the processing conditions and their influence on the local properties is important for predicting behavior in a component level test.

Increased use of powder-forged connecting rods in the automotive industry prompted an investigation into the suitability of powders from different suppliers for this application. Specifications developed by North American users call for ultra clean powders to enhance machinability and fatigue life. Powders from four manufacturers were each blended with graphite and lubricant, then pressed, sintered and forged to full density. Metallographic samples were prepared and evaluated for inclusion content. In addition, the powders were mixed to the composition of connecting rods, (C - 0.5%, Cu - 2% and MnS - 0.3%), and were similarly pressed, sintered and forged. Test bars were machined from the forged discs. Uniaxial fatigue tests were performed in the tension-compression mode and strain-life curves were developed. It was determined that all powders examined were very clean and were comparable in their inclusion content.

Shot peening is a commonly used surface treatment process used to improve the fatigue life of aircraft, automotive and other highly stressed structural components. This improvement is attributed to the formation of compressive residual stress on the surface layer of the material by the impingement of spherical media (shot). The compressive residual stress usually decreases the tensile stress created in the component by “in service” external forces and therefore increases the fatigue strength of the part. To quantify the improvement resulting from shot peening, the fatigue behavior of powder-forged connecting rods and laboratory test bars from the base material (2% copper steel), both in the stress-free (unpeened) and surface treated (shot peened) condition were compared. The fatigue data were correlated with the residual stress generated at the surface. The stress magnitude and depth were determined using x-ray diffraction analysis.

The SAE Large Male and Small Female Dummy Task Group has recommended a change to the Hybrid III dummy hip joint. This change was made because of a non-biofidelic interference in the current design that can influence chest accelerations. The modifications include a new femur casting shaft design and the addition of an elastomeric stop to the top of the casting. Static testing and Hyge sled tests were done to evaluate the modifications. Based on the results, the new design satisfied the requirements set by the SAE task group and reduced the influence of hip joint characteristics on chest accelerations.

Using instrumentation designed for the ultrasonic measurement of thickness, a technique has been devised for measuring the isotropic elastic constants of small samples, i. e., samples 1 mm in thickness and a minimum of 5 mm in other dimensions. Young's modulus, the shear modulus and Poisson's ratio are calculated from measurements of density and ultrasonic shear and longitudinal wave velocities. Samples of valve train materials, including chill cast iron, low alloy steel, tool steel, stainless steel, a nickel-base superalloy, and a powder metal alloy were machined from components and analyzed. The magnitude of the measured values of the elastic constants are reasonable when compared with published values. The measurement error on all the constants is estimated to be less than 1%. Moduli determined by this method can be used in finite element analyses to improve designs.

Systems of alloys for liquid phase alloying during sintering were investigated. The solidification range of alloys of Mn-Ni-Cr-Mo-Fe and Mn-Cu-Ni was determined. Alloys with the lowest and narrowest melting range were prepared and atomized in nitrogen. Admixtures of master alloys to water-atomized, forging grade, pure iron powder were sintered at 1232°C (2250°F). After hot forging, these P/M steels exhibited hardenabilities which were 75%-90% of theoretical hardenability, as calculated from the factors for conventional steels. Alloying efficiency was further improved to 85%-100% of theoretical hardenability when additions of approximately 2% silicon and 1% rare earth misch-metal were made to the master alloys. The silicon and rare earth misch-metal additions were used to enhance diffusion and sintering.

This paper presents the experience of Ford Motor Company and Hitachi Metals Ltd., in the development and design of the exhaust manifolds for the new 1997 Ford 6.8L, Vl0 gasoline truck engine. Due to the high-exhaust temperature 1000 °C (1832 °F), heat-resisting nodular graphite irons, such as high-silicon molybdenum iron and austenitic iron with nickel cannot meet the durability requirements, mainly thermal fatigue evaluation. The joint effort by both companies include initial manifold design, prototype development, engine simulation bench testing, failure analysis, material selections (ferritic or austenitic cast steel), production processes (casting, machining) and final inspection. This experience can well be applied to the design and development of new cast stainless-steel exhaust manifolds in the future. This is valid due to the fact that US EPA is requiring all car manufacturers to meet the new Bag 6-Emission Standards which will result in increased exhaust gas temperature.

An extremely tough alumina based ceramic coating produced by a modified anodizing process developed at Moscow Aviation Institute has been evaluated for light weight, wear resistant component applications in automotive powertrain. The process details and test results from comparative evaluation of friction and wear properties for cylinder bore application, referenced to cast iron baseline, are presented and discussed.

New high-temperature Mg alloys are being considered to replace 380 Al in transmission cases, wherein bolt-load retention, and creep, is of prime concern. One of these alloys is die cast AE42, which has much better creep properties than does AZ91D but is still not as creep resistant as 380 Al. It is thus important to investigate bolt-load retention and creep of AE42 as an initial step in assessing its suitability as a material for transmission housings. To that end, the bolt-load retention behavior of die-cast AE42, AZ91D and 380 Al have been examined using standard M10 bolts specially instrumented with stable high-temperature strain gages. The bolt-load retention test pieces were die cast in geometries approximating the flange and boss regions in typical bolted joints. Bolt-load retention properties were examined as a function of time (at least 100 hours), temperature (150 and 175 °C) and initial bolt preload (14 to 34 kN).

Fatigue characteristics of representative cold-rolled, high strength steels, in gages ranging from 0.072 in. (1.83 mm) to 0.055 in. (1.39 mm), were determined in fully-reversed, axial strain cycling at amplitudes up to 0.01. Alloys were selected from three families of high strength steels: recovery annealed steels, conventional microalloyed steels - nitrogenized steel and rephosphorized steel, and dual phase steel. Cold rolled low-carbon steel provided a comparative baseline. Cyclic stress-strain curves are presented to indicate the degree of cyclic stability achievable by various strengthening mechanisms while relative fatigue resistance is determined from strain-life curves. The implications of these behavioral trends to component down gaging are discussed.

APPLICATIONS of nuclear energy in automotive manufacture have been made principally in the field of radioactivity. These are grouped under the following categories: radiography, nondestructive testing, gaging and control, tracer techniques, and static neutralizers. Radioactivity techniques are being used in foundry operations to check stock and metal levels in cupolas and distribution of element additives. In steel operations, these techniques are being used to check assimilation of ore-concentrate fines and thickness of rolled sheet steel. Other applications include measurement of pipe and wall thickness in pressure lines and engines, and inspection of castings and welds for internal faults. Radioactive techniques for improving processes, quality, and materials have potentially universal application. Greater industrial access to reactors will permit broader study and speed the development of new applications of radio-activity in industry.

AMONG the many outstanding advantages of the shell molding process of casting crankshafts, as described here, are the following: 1. Manner in which entire process responds to a high degree of automation. 2. Close tolerances that can be maintained from casting to casting. 3. Raw sand requirements are reduced from 125 lb (previous method) to 20 lb. 4. Results in 70% reduction in weight of chips produced. 5. Resulting crankshafts have highest wear resistance and exceptional endurance. 6. Gives additional design leeway: Allowing the most efficient distribution of weight. Contributing to engine compactness by varying the casting contour to prevent potential interferences.

Engine dynamometer and laboratory flow reactor studies of automotive catalyst deactivation caused by the use of leaded fuel indicate that there are two different deactivation mechanisms: one, which dominates between 700 and 800 C, is the poisoning of the active platinum sites by lead oxide, or perhaps lead, and the other, which occurs below 550 C, is a build up of a gas diffusion barrier of lead sulfate. Both deactivation mechanisms can be temporarily reversed. Poisoning is reversed when the platinum is freed of lead oxide by lead sulfate formation below 650 C; and the barrier formed below 550 C can be made more permeable by thermal sintering of the lead sulfate at 600 to 700 C or its decomposition to lead oxide at 700 to 800 C. However, further exposure of the catalyst will again render it inactive via the mechanism predominating in that temperature region.