Search Results

Due to the increase of mining production and rising labor costs, manufacturers of construction and mining equipment are engaged in developing large tonnage mining truck with good dynamic performance and high transport efficiency. This paper focuses on the improvement of the dynamic performance of a 52t off-highway dump truck. According to the characteristics of its operating cycle, electric auxiliary drive system is installed in the front axle aiming at improving the utilization rate of ground adhesion. The new all-wheel drive hybrid electric system makes it possible for dump truck transports at a higher velocity. Both the conventional dump truck model and the new all-wheel drive hybrid truck model are built based on the AVL-Cruise platform. Meanwhile, under the premise of enough dynamic performance, fuel consumption can be minimized by collaborative optimization in Isight.

When driving in mountainous areas, vehicles often encounter long downhill sections. Due to the large mass of bus and the drum brake with poor heat dissipation effect, it is easy for bus to produce braking thermal decay in long downhill section, which makes the vehicle out of control and causes safety accidents. The braking methods of parallel hybrid electric bus include drum braking, engine braking and regenerative braking, whose torque models are established in this paper. The coasting test in Trucksim is used to verify the correctness of the engine braking torque model. Based on coupling braking torque curve with vehicle speed in different gradient, the stable speed is determined and the shift strategy is proposed. The temperature rise model of brake drum is established to analyze the temperature change of brake drum during long downhill. Then, according to the ramp data of G22 freeway, the above models are simulated.

Because of the long driving range and good power performance, plug-in hybrid electric vehicles (PHEV) have drawn much attention. And the current fuel-saving effect of PHEV still has a lot of room for improvement. The complex powertrain structure of PHEV makes the requirements for control strategy be increasing. Therefore, it is crucial to develop an efficient control strategy to ensure that the PHEV operates at optimal performance with an improved driving range. This paper establishes a mathematical model for fuel economy control of PHEV, by treating the torque distribution problem as a multi-stage decision optimization problem, and establishes a global energy management strategy based on a dynamic programming (DP) algorithm. Based on the actual physical model, this paper creatively solves the correction range of battery SOC value according to the charge and discharge power of the motor, which greatly reduces the calculation time of the DP algorithm.

For series hybrid electric vehicles (SHEV), rule-based strategies are realistic and powerful in real-time applications. However, the previous rule-based strategy cannot strike a balance between the best fuel economy and the best battery performance while maintaining the advantages of real-time applications. In order to obtain higher efficiency and reduce battery consumption, we have developed an adaptive hybrid thermostat strategy. On the basis of maintaining the load leveling of the thermostat strategy, the threshold-changing mechanism is added to realize the adaptive adjustment of the engine starting power under different SOC conditions, so as to achieve the goal of prolonging the battery life. In addition, the more fuel-efficient emergency handling rules designed to further reduce comprehensive fuel consumption.

The plug-in hybrid electric vehicle (PHEV) gradually moves into the mainstream market with its excellent power and energy consumption control, and has become the research target of many researchers. The energy management strategy of plug-in hybrid vehicles is more complicated than conventional gasoline vehicles. Therefore, there are still many problems to be solved in terms of power source distribution and energy saving and emission reduction. This research proposes a new solution and realizes it through simulation optimization, which improves the energy consumption and emission problems of PHEV to a certain extent. First, on the basis that MATLAB software has completed the modeling of the key components of the vehicle, the fuzzy controller of the vehicle is established considering the principle of the joint control of the engine and the electric motor.

Analogous to a vacuum boosted system, Electro-Hydraulic Braking System (EHB) is free from engine vacuum and supplies a braking force proportional to driver input. The independence of engine vacuum makes it especially suitable to be used in electric vehicles (EVs) and hybrid electric vehicles (HEVs). As a key component of EHB, master cylinder is driven by the pump rather than the vacuum booster. Even if the pump fails, the cylinder can also build proper pressure. Meanwhile, in order to maintain the pedal feeling, a pedal stroke simulator is applied in the system. In this paper, aiming at decreasing the size and cost of master cylinder and providing an ideal pedal feeling without compromise of performance, a new integrated master cylinder of EHB system is designed including two parts: master cylinder and pedal stroke simulator. The key components of the integrated master cylinder are motor pump, solenoid valves and composite springs.

Recovering the braking energy and reusing it can significantly improve the fuel economy of hybrid electric vehicles (HEVs).The battery ability of recovering electricity limits the improvement of the regenerative braking performance. As one way to solve this problem, the technology of brake-by-wire can be adopted in the HEVs to use the recovery dynamically. The use of high-power electrical equipment, such as electromechanical brake (EMB), is working in the form of brake-by-wire. Due to the nature of EMB, there exists an obvious coupling relationship between the energy flow and brake force distribution. In this paper, a brake force distribution controller is proposed in HEV with EMB, which can maximize braking energy recovery, compared with the conventional distribution control without EMB. Meanwhile, an energy flow strategy working with the distribution controller is designed, which is less limited to the performance of the battery.

During the drivability test process, a large amount of noise generated by a series of internal and external factors of the vehicle reduces the accuracy of the drivability evaluation. To solve this problem, this paper introduces the EEMD denoising method and compares the denoising effects of the EMD denoising method and EEMD denoising method on the original signal using the entropy weight evaluation index. In addition, the optimal parameter setting is obtained by comparing the denoising results of different parameter settings in the EEMD denoising method. The results show that when the white noise is integrated 3000 times and the standard deviation of white noise is 0.1, the EEMD noise reduction method is the best, and the comprehensive score of noise reduction is 0.732 points higher than that of EMD.